I've just discovered (after a panicked hour trying to work out what was going wrong) that my boot and system partitions for windows 7 are on different hard drives. The boot partition is on my 120GB SSD and the system partition is on my 320GB WD HDD.
This means that I have to have both hard drives plugged in for my system to boot. Obviously this isn't the best set up as if one of the hard drives fails then I'm screwed! Is there any way to fix this without having to re-install windows?
I have one HDD C: with Windows 7 64bit and another HDD from my previous dual boot PC with two partitions C: and E:, both winX pro.How is it possible to combine both HDDs, creating a multi boot system having as C: my Windows 7 drive?
Win 7 x64 Home Premium w/Gigabyte GA-EP45-UD3P, v.1.1 (P45), works great in IDE mode. (N.B.: eSATA port is just regular SATA port w/cable as provided by Gigabyte.) Trying to install external eSATA HDD. First I enabled AHCI drivers via registry. Then I turned on AHCI in BIOS. When I save BIOS and reboot, boot hangs when DVD writer performs sniffer boot, i.e., HDDs aren't found.
I'm new around here so, if you've seen this before, please bear with me.I have a computer with 3 hard disks in it as follows.Patriot Pyro 120 GB on Windows 7 Ultimate x64 (installed first).WD Velociraptor 450 GB on Windows 8 Pro x64 (installed second).Samsung something 2 TB storage (forget about this one).The 2 operating systems are completely independent and functioning properly; obviously, the SSD (Pyro) is set to boot first in the bios and, at start-up, there's no boot manager asking me which OS I intend to use. Basically, every time I want to logon on my Velociraptor with Windows 8 I have to press F8 at start-up and choose from the given list of bootable HDDs.Now, I've tried EasyBCD without luck and I've read somewhere that, apparently, the Windows 7 boot manager can't boot a Windows 8 partition so, my question is, is there a way to add my Windows 8 Velociraptor to the boot manager of the first booting HDD, i.e the SSD with Windows 7?
i have an odd 5900 RPM HDD that i need to swap out. i'm going to swap it out mainly because it's better suited for storage/backup rather than being my main HDD for usage/boot-up.
i don't want to reinstall Windows 7 (7100) and i want to copy everything from HDD "a" to HDD "b". any ideas/suggestions/comments?
I am upgrading my HTPC that i put together a few years back to have a SSD as a boot drive to increase space, quiet background running and speed up booting, etc.Everything was running fine before trying to exchange the raptor for the m4. I had a big issue getting Windows installed on m4 but finally did a clean install when no harddrive was connected except the SSD to the original SATA port of the boot drive. Once I had windows installed, and i was able to boot up with only the SSD attached to the boot SATA port, I attached the 3 storage drives to their original SATA ports and got an error when booting... it paused in mid boot, then started searching for a boot disk in the DVD drive. I looked at the BIOS and the SSD is listed as 1st (port0) on hard drive boot order and hard drive is 1st boot priority. I unplugged all 3 storage drives and it booted up without an issue
I've done some searching for this and found some similar issues but nothing fits exactly what I'm trying to do. I have been running Vista Ult. 64 bit for a little over a year and have loved it. It solved all the problems I had with XP Pro 32 bit on my hardware. I bought 7 Pro 64 bit through www.theultimatesteal.com since I'm taking some night classes. I forgot I couldn't upgrade from Ult.
to Pro so I had to do a clean install, which I did, on a separate drive. I have five drives in my system, C, D, and E are all 1TB while F and G are 1.5TB. C is where Vista is installed and G is where 7 is located. I'll be going back and forth between the OS's until I get everything the way I want it.
At that point I want to remove Vista and have 7 be the only OS. But I do not want to migrate the install onto the 1TB C: drive, I want to keep it on the 1.5TB drive but have it recognized as the C: drive. The install was done from within Vista from the download since my physical media has not yet arrived. So even when I boot into 7, it is seen as being installed on the G: drive; it did not make itself the C: drive.
So I'll need to get rid of Vista, get 7 to see itself as being the C: drive, get rid of the boot menu, and swap the drives and cables around to put my 7 install at the head of the HDD pack. I've already done a full system backup of my Vista install with Acronis TIH 2010. How do I need to go about this? On another note; why did MS only offer home and pro through ultimate steal? They offered Vista Ultimate. I mean, it is called ULTIMATE steal, not Pro steal afterall, and it would have made the upgrade process that much easier.
I want to combine my 2 desktops into one, since I never use both together and the older one is very dated by now (think Time/tiny computers old). My current machine is an Asus P5Q-E with a C2D and has one HDD on a SATA connection running windows 7 64bit. The old computer is a single core Athlon 2700+ thing with a pair of hard drives on a single IDE ribbon.What I want to do is put the hard drives from the old machine into the newer and be able to choose between Windows XP already installed on the old master IDE hard drive and Windows 7 on the newer SATA drive (I've only kept the old computer to run XP for compatibility), all the while keeping the old slave IDE drive as a slave.
So I tried installing Windows on my new machine and did waht seemed to be the recommended thing and plugged in only my SSD into the Sata port, leaving my other drives unplugged until after the installation. Everything went fine and I was able to get Windows 7 up, drivers were installing and everything was peachy, but Then I plugged in my other drives, and when I did so with the computer running Windows immediately recognized them and I could access them, as well as do whatever I wanted. However when I restarted I got the message BOOTMGR is missing.
Now, you may be thinking that this is a simple issue of it trying to load from one of those other HDDs, just set the boot order in the BIOS blah blah. But its not. I set the boot order in the BIOS to use the SSD, I set the SSD to the top of the list within the HDDS priority order and still nothing. I then took it a step further and instead of selecting the order manually told it to boot from the SSD flat out, boot from this drive and the same error message came up. I already did the boot from Windows disc, startup repair thing - didn't work.
I have just installed a new P5G41T-M LX Series motherboard and two DDR3 x 2GB replacing DDR2. During startup a message says BOOTMGR is missing, press Ctrl Alt Delete to restart, on restart the same message is repeated.
I would like to remove Vista from my dual boot setup. Here is how I got to where I am now.
I had Vista installed on my PC hard drive (was C. Later, I decided to install Windows 7 HP on a new and seperate HDD. I unplugged the Vista HDD and added the new HDD and installed Windows 7 as if from scratch (I was worried that the install would mess up all my files on Vista). After the Windows 7 was up and running, I then reconnected Vista redesignated it as drive E: and after some searching on how to, I created the dual boot using my Windows 7 disk so I'm assuming the boot file in on drive C: along with Windows 7.
I now want delete the dual boot and Vista so I can use the drive as a backup drive or possibly Win8. I have found several methods to do this but none that really have my specific situation.
My machine came with Windows7 pre-installed and no installation DVD, instead there is a separate partition labelled WINRE (5GB) for recovery purposes (I guess at least).Now I messed up my whole system and deleted all partitions but this recovery one (setting up a dual boot). I also have the System Recovery Disk and would anybody know if I can reinstall Windows 7 with these two?
I'm trying to reload a windows xp sp3 system with 5 partitions. root partition (c:) has bcdedit.exe and store. z: is application store with bunch of batch scripts.A web application is hosted in Apache omcat on c:. One of the cgi script in web application calls a batch file on z: drive with following command.
BCDEDIT.exe /store c:ootcd ootsequence {UUID}
I'm getting following error
The boot configuration data tore could not be opened. A required privilege is not held by the client.
I do not see error, if command is run from command prompt with admin privilege. my web app is running under admin privileges.
I have win 7 booting from a 256GB SSD. All data is elsewhere, so there is a lot of room on this drive. Are there any problems with creating a partition on the SSD to install Win 8 on? I have read tutorials on how to set up a dual-boot 7/8 system. They generally state that Win 8 should go onto a separate drive. Wouldn't a separate partition work just as well?
I have 3 identical PCs with 2 partitions: C and D.I created a system image for one PC, C only.But when I restore that system image into the other 2 PCs (using Wind7 DVD), it formats both C and D and restore.The problem is that I have data on D and I don't want it to be formatted. I only want to restore the C image.
A little background on my system's configuration. My system was/is configured is a two disk RAID0 with a system partition and two other partition for Windows and programs. I'm wanting to migrate the partitions/data to a single disk system. I created a system image using both the Windows backup software and Novabackup. The problem I'm having is restoring either of those images to a single disk. Is it possible to restore an image from a RAID configuration to a single disk? If so, what am I missing? No matter which image I try to restore from, I either get a fail from Windows or can't be done in so many words from Novabackup. I just want the RAID image on a single disk.
I want to dual boot xp and windows 7 on two different partitions. And I want to have an additional partition for programs and one for user documents. Is it possible for the two os's to have the same shared program files directory.reason for this is to save space instead of having different installs for each just have them both run off the same directory.
I'm about to install my new 256gb SSD. This will have 3 partitions;
100mb System reserved partition 80gb Windows OS partition The rest will be used for VHDs
So, using disk part.. are these the correct commands in the correct sequence (Having unplugged my spinners first so diskpart only sees one drive
select disk 0 clean create partition primary size=100 align=1024 create partition primary size=80000 select partition 1 format quick fs=ntfs active exit
Should I also be formatting the S/R partition? I will create the final partition via disk management when windows is installed. This will result in 3 partitions, all properly aligned etc. Yes? Or am I on some far off planet?
I have an Acer Aspire 1810TZ with Windows 7 Home Premium 64-bit. The HDD is 160GB.Yesterday I moved (without resizing!) both the 100MB system reserved partition and my 40GB C: partition towards the "beginning" of the HDD for the purpose of creating an unallocated space of some 110GB towards the "end" of the HDD. (The C: partition had previously been shrunk using Win7 disk management and the system worked fine after reboot prior to partition move).llowing the partition move I can however not boot into Windows anymore. Windows boot manager gives the following info:Status: 0xc0000225Info: The boot selection failed because a required device is inaccessibleThe boot manager also suggests I reinstall Windows, but of course the restore and rescue DVDs I burned based on Acer's eRecovery tool does not work.
I have 2 SSDs each partitioned into 80GB and 40GB like this:
-Drive1-80GB (boot) and Drive1-40GB -Drive2-80GB and Drive2-40GB
Drive1-80GB is already the Windows 7-64 boot partition for the system. Can I configure a software RAID-0 with Drive1-40GB and Drive2-40GB? I know this is unorthodox but I wanted to try this for a few reasons.
It came with 2 primary partitions: a 650 gb C drive (boot) and a 50 gb D drive (recover). Because the windows partition tool didn't let me reduce the partition size by more than 50%, I decided to use EaseUS partition master to do that. I made D drive logical and renamed it to F, made the C drive 200 gb and made a new 400 gb logical drive and named it D. Then I restarted the laptop and let the tool do its work. After this, the problem started. I couldn't get past the bios screen, and couldn't even tap F2 and F8 to get in the boot menu. When I inserted my windows 7 recovery dvd, I heard the dvd drive working, but nothing happened. When I plugged in a usb drive, however, the laptop loaded the cd drive and I could reinstall windows 7 from the cd. Windows works now, actually, even my old windows installation still works, but I still can't boot up without inserting the usb drive first.
I have a PC with 2 hard drives- the first hard drive has a single partition and windows 7 64-bit is installed on this hard disk.Now I wish to install CentOS 6 on the first partition of the second hard disk.I have created the dvd for installing Cent OS also.How do I configure the boot loader in Windows? If I install Linux on second hard disk, will this overwrite the Windows Boot Loader? How do I create a dual boot system so that the windows boot loader correctly shows linux as an option, so that I am able to load either Windows 7 (existing) or Linux(on second hard disk- not yet installed)
1. "System reserve" which contains e.g.the Bootmamanger and MBR 2. First Win 7 installation ("main") 3. Second Win 7 installation ("reserve")
When I boot now at first the Bootmanager on the first primary partition is called/started which in turn starts the boot menu. In the boot menu there are currently two entries:
Windows 7 Windows 7
So I cannot distinguish between the "main" and the "reserve" Win 7 installation. How exactly can I modify/rename the two "Windows 7" entries in boot menu? After selecting and booting the actual Windows 7 installation the other Windows 7 installation is visible as a separate partition in WinExplorer:
C: Running Windows 7 D: DVD drive E: Other (non-booted) Windows 7
How can I automatically hide the other Windows 7 installation? The drive E: should be available e.g. for USB sticks or network drives.
One of my friends has a windows 7 computer with an account for himself, his mother and his 2 sisters. All the home directorys are stored in drive C. Partition D is shared. The question is, how to get a partition layout like this?
Partition 1: OS + programs Partition 2: home partition for himself Partition 3: home partition for his mother Partition 4: home partition for his sister Partition 5: home partition for his other sister Partition 6: shared partition for some photos.
I have just purchased a new pc that came with Windows 7 Home Premium 64-bit, which wont run my company software, which was made in 1995, 16 bit. This 16bit software ran fine on my previous pc, which had Windows 7 Starter 32-bit. But the 64 bit Windows 7 version wont run it, I cant use Windows XP Mode on my version of Windows 7, need Pro - Ultimate Version.
I want to install and run the Windows 7 32-bit I have, on my new pc (I still have the installation disk) on a separate partition and keep the 64 bit version to. Is this possible to install both 32 bit and 64 bit versions of Windows 7 and then select which to run when the pc boots?
I have 3 partitions on my hard drive. First partition is for Windows XP and the second is Windows 7 and the third is for data.My question is how does having 2 partitions impact booting into safe mode? I assume that both XP and Windows 7 have their own safe mode? I am asking because I need to get into windows 7 safe mode in order to install a piece of software.
All PSU SATA power cables I've seen have only four connectors on each cable. Assuming the rail can handle the load and the wire used is large enough to avoid a voltage drop, is there any reason why there can't be more than four HDDs on a cable?
What I am wanting to do is run an SSD (boot/program) and six data drives (probably 2 TB WD Greens) on a single cable that I can make up (the PSU is a modular Corsair HX750; a bit oversized but that will cut down on heat and, hopefully, increase the life of the PSU) to cut down on cable clutter (the case I want to use is a bit tight; space to put it is a problem so it needs to be small). The original cables are made with 18 AWG wire. By using #14 AWG wire, the calculated voltage drop at the last HDD in the string (the SDD would be first) will actually be less than on the Corsair cable. The computer would read or write to no more than two of the HDDs (and the SDD) at any one time. There will also be two hot swap bays (3.5" and 2.5") in the computer (for making back ups) as well as an optical drive but each one of those three will get their own cable.
I have 2 HDDs that I want to switch the OS of each one to the other. One is a laptop 140GB HD that has Windows 7 64-bit and the other is a Desktop 150GB HD with Windows XP 32-bit. The laptops HD was pre-installed with the OS and the Desktop is unknown. Just as an fyi the laptops cd drive is broken and the desktops doesn't burn. What are my options on how to switch the two?
How to set up my 120 GB SSD as just my OS Drive then use my 1 TB and my 750 and another 750 for data etc. So I have backed up all my data from my current install (right now I am running my OS from the 1 tb and the SSD isn't even being used yet. I just wanted to know the best way to set it up so I can use the SSD JUST FOR THE OS and then install programs and steam etc in the 1 TB (cuz i got at least 500 GB of games from steam). Can I just install the OS on the SSD then format my 1 TB and make 3 folders Users, Program Files and Program Files (x86), and then install programs in to the appropriate folders? User Profiles - Create and Move During Windows 7 Installation.
I am running VMWare Workstation.I am very new to this.After a couple installs of the Workstation, I was able to create and power on Linux VMs on the Workstation.But the thing is it just sees itself (the VM) and the removable devices I put on there, but not the HDDs on my computer.
