About 8 months ago, I built a computer for myself;SINGLE Hard drive, 1 T;1 Partition..Windows 7 Home Premium service pack 1..The BIOS identifies the HDD..Last week, the computer worked properly, with regular shut down.3 or 4 days later, when the PC was turned on, it booted through the Windows 7 splash screen, but the log on screen did not appear.After a spontaneous reboot, the Windows 7 repair utility informed me that the situation could not be fixed. I selected advanced options and tried 2 different restore points from about a week before the last happy event. [code]
I have Windows 7 ultimate 64-bit installed on DELL desktop (Optiplex 990) i7 Core. I have two HDD: Disk 0 contains the operating system 500GB. and Disk 1 empty 1TB.
I want to make a partition on disk 1 to mirror the operating system partition and keep the remaining for data storage. I tried to do but I had the following error message: "All disks holding extents for a given volume must have the same sector size, and the sector size must be valid."
problem started within the last two weeks. PC just started boosting fan noise and then just blacked out. now each time i turned it on, it will give me 2 options prior loading system: 1) start-up repair - recommended, and 2) start windows normally. i've tried both but it just blacked out every time after a few seconds so i never got to the welcome screen.
i already tried these:1. replacing hard disk with one from broken PC and same problem as above. 2) corrected modem fan because it got fixed the wrong way by someone when they replaced the burned power supply. 3) re-seated the 2 ram sticks. 4) hooking hdd cable onto another slot on the motherboard.
maybe it is also important to note that pressing power button turns on the computer but the power-on light never even blinks or stay on except the hdd light which eventually goes out after a moment.
Suddenly my Win 7 Home Premium x64 will not boot. The system starts, POSTs then loads the DVD driver, then the screen goes black (not blank but "lit up" black if that makes sense). Then nothing. If I use Hiren's boot cd I can boot up using the "boot from HDD" option fine and Windows operates normally. System restore to a previous configuration made no difference to the original problem. I cannot boot into Safe Mode. F8 just offers me boot order options.
- Running the Windows 7 DVD I find: "No operating system is listed on the Repair Windows option." - Running Startup Repair finds the following error: "the partition table does not have a valid system partition" which it claims to have repaired, but the error remains and Windows will still not boot.
I followed this advice: Boot 7 dvd to system recovery options command prompt. Type: Diskpart list vol (find the vol letter e.g C or partition number e.g. 1 for the system partition ) Sel vol C ( or sel vol 1, obviously use the correct letter or number) act exi
My system partition was easily identified and listed as healthy so I selected it and made it active. The problem still remains exactly the same. My system is self built just over a year ago, to my knowledge has been running fine, without any hardware issues. I'm prepared to do a clean install if that's what it takes but if there is a way to fix the partition problem without that I'd like to explore it first.
Pretty much what happened is that my powersupply got messed up one day and just turned off my computer and I couldn't boot it back up. I ordered a new PSU and I installed it but now when I boot my computer I'm getting "Disk boot failure, insert system disk and press enter". I've tried putting in the installation disc and using the recovery options but my OS isn't listed/found and if I click load drivers I can clearly see both of my hard drives. I have already checked boot options as well. I was also using GRUB before this all happened as well because I installed ubuntu as a dualboot.
Here is what happened to me, I had windows 7 installed on a SATA HDD. I bought an SSD and installed a fresh copy of windows 7 on the SSD. then I took out the SATA harddrive which I learned it contained the system parition. Now the new windows doesnt boot.
If I open diskpart and do a LIST VOL I only get one which is the SSD and inside I only have one partition with the windows files.
After a few comamnd I was able to see the installation when I start the recovery console. but when boot up. as soon as the little cicles for the windows logo comes up it freezes and reboots.
I tried making the volume parition active, but from what I have read, looks like I need to create a system parition. Is that possible. or do I have to reinstall from scrtach. (the old SATA drive is formated so no going back) Its just so close, i see my data intact on the drive lol but cant get windows to boot.
I have my HP Laptop which came with Windows Vista as the OS. I want to upgrade to Windows 7 so I bought Windows 7 from my local store.I entered the disc and did boot from CD. It reached to the page where it shows the disk partition. I deleted the partitions and created new one. However, whenever I create the partition, it creates a primary one and gives me error saying Setup was unable to create a new system partition or locate an existing system partition.
I was trying to get a dual boot setup of Windows 7 and Ubuntu where I had 1 partition for Windows 7, another for Ubuntu, and a third neutral partition accessible from either OS where I would house all of my data. The problem is, my computer already had 3 partitions set up: Windows 7, the system boot partition, and one called PQService. Because I could not find a tutorial to delete pqservice, I decided to delete my system partition, even though this seemed a little more risky (apparently it was lol.) I used this tutorial: TeraByte Unlimited Knowledge Base to copy the boot files to the windows partition and delete it. I then booted into a Live CD of Ubuntu, and used Gparted to move my Windows 7 partition in order to get rid of the 100MB of unallocated hard drive space. I then attempted to restart my computer into Windows and i got an error saying that windows could not boot because of some recent hardware changes. Is there anyway I could get back into windows without reinstalling it? Do I need to figure out some way to restore my System partition? Is there someway I could get windows to boot without doing either of those?
My wife shout down her computer this morning took it on remote location for work today but never booted it up. When she got back home tonight it wouldn't boot up. I don't know what to call these screen but some Startup Repair screen. Just says Repair action: Boot sector repair, Result: Failed.I downloaded and burned to CD the boot CD for the MiniTool Partition Wizard Home Edition but I don't know what disk I am even looking for. I see 3 partitions listed for one disk.The only one with a label is BDEDrive and it's 300 MB. The other two have *: as what I would call a label. One is 297.79 GB and the other is 12.34 MB. The BDEDrive is the only with with status of Active. NTFS on that partition and Other on the big partition.
im usin 2tb segate new hard disk sir..in my system i cant able to boot my os and also my hard disk...its showin that hard disk boot failure insert system disk press enter ...i restarted many times its sayin the same problem...in my gigabite mobo bios my hard disk is not get detected sir....the problem is that wen im installin the new os for 2nd time its all went nice only sir but at the completion of the os it wil ask for the user name and password but in my system its frozen sir fully of black screen and i cant able to do anythin so i restarted my system from that im gettin this error as hard disk boot failure insert system disk press enter.....that my new hard disk and all of my data is in that hard disk only..this problem arises wen im installing the os for 2nd time sir.
I woke up this morning, and I found that my computer was displaying this message"Disk boot failure, insert system disk and press enter". There are a ton of needed documents on the computer, and I'm hoping that they can be saved some way.
I've been having this error even after reformatting and reinstalling Windows 7 on my desktop. I've done reformatting / reinstalling Windows 7 several times, yet the problem still occurs. I'm thinking of my HDD as being corrupted or messed up. The problem occurred after I accidentally hit the CPU when I was stretching my foot. The screen froze after that. Upon rebooting it, 'Disk boot failure, Insert system disk and press enter' occurs. After I entered the DVD installer of Windows 7, the screen just hangs.
My friend bought a new PC and needed to put am OS on it. He put in the W7 disk and the error message 'disk boot failure insert system disk and press enter' appeared before installation was shown. He has tried changing around BIOS and it also recognises the hard drive and DVD/ CD ROM drive. Here is the specification he was given:Case : CIT Reaper Black Mesh fronted Tower CaseMotherboard : Gigabyte 78LMT Motherboard TechnologyCPU : AMD Bulldozer FX 4170 4.2ghz 8mb CacheHard Drive : 1tb Sata Hard DriveMemory : 8gb DDR3 1600mhz MemoryOptical Drive : 24x Dual Layer Sata DVD WriterGraphics Card : Nvidia Geforce GTX 650 2gb GDDR5 With HDMIPower Supply : 750 Watt Branded Power Supply Also, he has tried booting BIOS in different order
I have a copy of windows 7 from a friend. (USB, possibly enterprise)It runs well, is official and can be re installed and is verified through the Microsoft site, so the media doesn't seem to be a problem.I was able to install Win7 Ult x64 on my WinVista HomePrem x86, but I went back through to clean the hard drive (it was full, I didn't format before) and after low level formatting I cannot reinstall the OS. The harddrives are completely empty, and I get stuck at "Setup was unable to create a new system partition or locate an existing system partition," after hitting next when you are selecting the HD partition to install on. I tried a couple of things already:
-Installing on another harddrive -Formatting using Hiren's bootcd -Using a hard drive with XP installed to see if it is an upgrade and not a full version (no luck, still wouldn't install) -diskpart > list disk > select disk 0 > list partition > active \ in cmd..I have three hard drives attached to the computer right now, they can't all be broken. T.T
When starting the computer, I keep getting "Disk boot failure, insert system disk and press enter". Nothing works other than putting in the boot disk and hitting the restart button on the tower. Then it will boot up and run fine. But how do I stop it from having to have the disk in order to load? Checked in the BIOS and the hard drive is the first load.
I have a brand new Windows 7 64bit build with a clean install from an Upgrade CD and noticed in BIOS that my 1st boot device must be "Windows Boot Manager" or it asks for the CD. I only have 1 storage device (SSD) in the system and when I look under Disk Management in windows, it shows a 100MB "EFI System Partition" in addition to the primary partition (which is labeled "Boot, Crash Dump, and Primary Partition" - so it seems to have the boot files on it).
As I only have the one non-optical storage device I did not set any partition parameters at install. I Attempted to do a Startup Repair with the windows disc to maybe try and delete the EFI partition and got the "... System Recovery Options is incompatible with the version you are trying to repair" error. Not sure what that is. If Disk Management shows a healthy partition with "Boot" listed as being contained, why can I not select the SSD as boot device #1? I can boot perfectly fine with the Windows Boot Manager listed as boot device #1 and the SSD as #2, however it's not ideal.
Recently my SSD failed so I tried installing windows 7 from DVD on my HDD but I always get an error message: "Setup was unable to create a new system partition or locate an existing system partition."I've tried everything I could find here: I gave boot priority to the HDD, I unplugged every other device but nothing seems to work.
Through a series of shenanigans involving experiments with mirroring on Windows 7 64 bit using Disk Management, and then subsequently removing the mirror after having recurring errors/problems with the synching, My 100MB System Reserve partition has ended up on a separate partition than my system image. For instance: Disk 1 System C: Healthy (Boot, page...) Disk 0 Healthy (System Reserved...).
In addition, the System Reserved partition has been assigned a drive letter "G:" or "E:" and is now visible in explorer and it won't allow me to remove it and supress from explorer view.
I'd like to
1) move/create the System Reserve partition to Disk 1 (with System C: drive)
2) remove the System Reserve partition from Disk 0 to free it all up as a data drive
Do I use command below to create a System Reserve on Disk 1? bcdboot C:Windows How do I then delete the System Reserve partition on Disk 0. Also a byproduct of all of this, when I reboot now, I have a "Windows 7" option and a "Windows 7 Secondary Plex" option. The "Windows 7" option no longer boots (it's stops while the logo panes are flying in circles to form the logo and goes into a fix loop that never fixes it). I have a feeling it's looking for the old mirrored hardware configuration or something. However, "Window 7 Secondary Plex" option does boot just fine. Do I use MSCONFIG to remove the "Windows 7" boot entry so I don't get this annoying option at boot?
I want to do a 'custom' reinstall on my C: drive. It's clogged with unused programs and it runs very slow.I set the BOIS to boot from HD and CD; neither worked. I purchased a new HD and may want to install it as my C: drive.I set the BOIS to boot from CD; still I get the dreaded message:"Disk boot failure insert system disk and and press enter"I recently installed a new mother board due to the fact it was defective, not as an upgrade.To make it clear I already had Win7 Ultimate installed. On my first attempt to perform #1 I got to the question of which install did I want; I clicked 'custom'. From then on nothing happened, and now I keep getting "THE DREADED MESSAGE".I put my win7 disk in another OSXP computer and it displayed, "This disk is not compatible with this system" so I assumed my disc was not corrupt.I bought my win7 disk legally on line a couple of years ago, and I have used it once. Will that be the problem? I never got to the "License key" so I don't see how it could be?
My computer wouldn't start after a power failure during resizing partitions. I tried downloaded and used Repair Disk for Windows 7 64bit, which leads to the relevant screens but after a repeated restart of the system a note "...Interrupted operation: Insert the Recovery CD or other Recovery Media and reboot your PC..." still appears for already couple dozen restarts. I've purchased my Sony Vaio VPC23FX laptop with no additional disks and anything. Should I buy a new copy of Windows 4 Home Premium and start everything from a blank page or are there any other ways to make the computer start properly?
I noticed this problem when I tried to delete something off the drive, then I tried to run an antivirus scan and it gave me an error if incapacity to delete viruses due to a dirty disk and that I should run chkdsk.So I right clock on the drive and attempt check now. It tells me that it must first dismount the drive before it can do so and asks if I would like to force a dismount. To which I respond yes. Then, the window disappears and I hear no word or see no signs of any chkdsk happening. Naturally I reboot the terminal expecting fire-works and chemistry, but get greeted by the sound of windows starting up again.I have tried the administrator driven command prompt in this sequence. C:WindowsSystem32>chkdsk x:/f
response: The type of file system is exFAT. Volume Serial Number is 2C7E-22C5 C:WindowsSystem32> then: C:WindowsSystem32>chkdsk x:/r response: The type of the file system is exFAT.
Chkdsk cannot run because the volume is in use by another process. Chkdsk May run if this volume is dismounted first. ALL OPENED HANDLES TO THIS VOLUME WOULD THEN BE INVALID. Would you like to force a dismount on this volume? <Y/N> response:
Volume dismounted. ALL opened handles to this volume are now invalid. Volume Serial Number is 2C7E-22C5 C:WindowsSystem32> then: C:WindowsSystem32>chkdsk x:/r
I have a Dell Inspiron laptop that got a virus on it. I tried to fix the virus but was just not able to and every time I turned the computer on it would get an error message and ask if I wanted to start windows normally, once in a while I would get a BSOD and it would reset itself. I don't remember what the error messages were because I kinda ignored the problem for a couple months and finally got around to saving what I needed and trying to do a reset. Everything went fine when I went into Dells Datasafe Restore. After it wiped the drive and re-installed I got past the Dell screen at startup and on to the windows screen then suddenly got a flash of a BSOD then the computer restarted. I went through the startup repair and got the message Failure while setup is in progress. I've been searching for a solution for a few hours now and I haven't found one. I don't have a recovery disk (I was just trying to use the partition) and I don't have a windows 7 cd. Where do I go from here?
whenever I turn on the laptop, it seems to boot into Windows 7, in that the "Starting Windows" text appears and the little animation of colors forming the logo shows, but as some point it fails. This message appears on screen:autocheck not found - skipping AUTOCHECK After a few seconds a BSOD shows up, but too fast for me to make out what it says. It used to, but after some hasty fix attempts no longer does, cycle around to a menu that informed me of this error:Status: 0xc000000f Info: The boot selection failed because a required device is inaccessible. Here's the longer history:As some point in the past I decided to try out dual-booting Windows 7 and Linux on the laptop. I got it to a state where this worked fine. I had partitions roughly as follows:[Ubuntu][Windows 7]([Data and files][Boot]) The parentheses denote a logical partition. The Boot partition was very small and only held what was necessary to launch GRUB. This week, I realized that I hardly ever used the Linux partition and decided to get rid of it to reclaim storage space. This is where the trouble begins. I rebooted into a thumb drive that could run GParted and modified the hard drive layout in the following steps: Delete the Ubuntu partition Delete the Boot partition Grow the Data/Files partition to take up the space left by Boot Shrink the Windows 7 partition to make it faster to move Move the Windows 7 partition to the front of the volume Expand it to take up the remaining space. What I ended up with was: [Windows 7]([Data and files]) My naive and fatal mistake was to trust that the Windows Repair CD could fix any boot issues, and also that there would be no catastrophic hardware failures. Both of these assumptions turned out to be false.
First, the laptop's CD/DVD drive has either broken or is too unreliable to use. I have noticed it becoming more and more unstable over time, but now (when I need it most!) it simply does not seem to want to spin up and function at all. This forced me to create a Windows Repair USB drive. However, I can't load any installation media. This is because the laptop did not come with an install DVD. It had a recovery sector, which I cannibalized for the Linux partition. I did copy the stock recovery stuff to a series of DVDs, but, well...This is all to say that any solution that requires a DVD drive is straight out until I can replace it, which I'd like to consider a last resort.My expectations for the Windows Repair CD/USB have been dashed. Attempting to automatically fix boot issues either fails for some specific reason (I can probably reproduce it and provide the details, if necessary), with a dialog to send a report, or fails because it cannot detect any problems. I have tried a variety of things based on my own research to fix this through the command prompt: Running chkdsk /x /r on all drives. Does not find any errors. Running various bootrec commands: /fixmbr, /fixboot, /rebuildbcd, /scanos. All complete successfully, but the last 2 report finding 0 Windows installations. Using bcdboot and bootsect to recreate the bootloader. Again, no errors result, but it does not fix the issue. I guess it should have been obvious that none of the boot record fixes would matter, since the laptop does boot into Windows 7, briefly.
I'm a long-time reader but new poster. I am currently running Windows 7. I want to install Windows XP onto another disc and have a dual-boot setup. I keep Windows 7 up to date and secure, but for the XP partition, I would rather not have antivirus running or even installed, in order to limit background processes. I will not be logging into any place or making any credit card purchases when booted into Windows XP. It will just be used for surfing, games, etc. Further, if and when XP becomes compromised or buggy, I will simply overwrite the partition with a backup image.
If I use Bitlocker to lock down the Windows 7 partition (with the encryption key on a thumb drive) and boot into Windows XP, am I correct in thinking the XP installation see or can't access the Windows 7 partition? If XP gets compromised, can a virus access or write to the Windows 7 partition?
Is there any other reason why this would not be secure? Can a virus write to the BIOS?
I wanted to resize a partition, so I backuped all important files and booted from a vista PE CD. The program used is called "Easeus". After the resizing a message appeared, which told me that the system information couldnt be updated. After a restart, it - well, it didnt restarted. I tryed to format my C:Windows partition, but Easus decided to randomly format my linux partitin, too. Yey. After that i just formated everything, so i can create one big partition so this never happens again :P. To put it in a nutshel, there is no way to boot besides from booting from a cd. The diagnostic tool of the fabricator is giving me the "error code: BIOHD-3 No bootable drives detected" message.I tried to fix it with a win7 repair disk (just realized, that the disk is for 64bit, i have a 32 bit os - i think it doesnt matter, because there isnt any os installed at all). I used pretty much every "bootrec" command, sucessful, but no change. The startup repair gave this message: "the partition table does not have a valid system partition" diskpart - act isnt helping either: "The specified partition type is not valid for this operation."I dont know if i could install any os from a disk - i dont have a bootable installation cd/dvd. Because of that i would be happy if someone can tell me where i can find a free os and how i install it. From a os i can install my win 7.
I currently have a dual boot on my computer with Windows 7 and XP. Unfortunately as my computer is quite old my hard drive is not very big and with it being partitioned I am fast running out of disk space. So I tried to shrink the XP partition to allow me more disk space for Windows 7. Unfortunatley this would only let me shrink it by 83mb for some reason. I decided that since I barely use XP anymore that I would simply reformat the XP drive then try and merge them together. When I tried to format the partition it just gave the error "Windows was unable to complete the format". I then discovered in Disk Management that the Windows XP partition was the system partition which was causing the problem.
I have started the installation process of windows 7 on a clean 1 TB hard drive. In order to ensure expediency of the read time of my primary drive, I choose the custom installation. When I did I partioned the drive as 250GB & 700GB. Hoever it also created a 100MB system partition on its own. It never did this in Vista. Is it suppose to do that?
I'm building a new computer. Can I partition the hard disk, copy my laptop HD to boot from one partition and run a new windows 7 pro os from the second partition?
