Iam trying to install XP-Proff on HP pavillion desk top , i formated the vista and tryed toinstall xp, system is not booting through the XP Boot able CD, i tried several times to do that, can any one helpme to how toinstall XP in HP pevillion desktop ,ifully formated the Vista verson,
View 5 RepliesI went to turn it on this morning, I just had a black screen showing the following words;
Press F2 to run
Press F11 to boot menu
Auto detecting PRI Master Atapai CDROM.
It then went to reboot and select proper boot device or insert boot media in selected boot device and press a key. I went into the BIOS to change the boot order and inserted my Vista home premium 32bit. I then got windows is loading in files. After a short while I got the black start up screen with Microsoft Corporation but after a few seconds it just froze. Moments later it went to a blue screen with white writing part of which said the following; A PROBLEM HAS BEEN DETECTED AND WINDOWS HAS BEEN SHUT DOWN TO PREVENT DAMAGE TI YOUR COMPUTER.
i installed vista 64 ultimate with 3 gig of ram but i was told that vista 64 could run with 4 so when i installed the 4th gig or ram my pc would turn on but not boot (did not see any display) so a friend told me that it is a known issue and to fix it i needed to reinstall service pack 1 with just 2 gig then that would allow me to install the full 4....i did this and now my comp will not boot unless i have just 2 gig, it wont even boot with 3 gig like before,
View 9 Replies View RelatedI install Vista Ultimate on one PC. It is an HP Pavilion a1700n. I remove the 40 GB IDE HD from the HP PC and put it into a Compaq EVO 510 PC. Result: Vista does not boot. I have researched the subject but still have not found a solution. The microsoft vista deployment step by step seems awfully complex.
Has anyone found a simple way to solve this problem? I have also tried the reverse (from compaq to HP PC): Same result! With XP I could boot into safe mode or just boot normally and XP would detect and install the new hardware it finds. Somtimes I would need to install XP from CD on the target PC to copy the boot.ini and hall.dll files to a usb flash drive. Then I would restore the image of XP on the target PC. I would boot into recovery console and copy the files form the flash drive to the target PC (boot.ini to C: and hal.dll to C:windowssystem32). Most times I could then boot the target PC normally or in safe mode.
i am running window 7 and vista. vista is on a 250 hard drive. window 7 is on a 500 hard drive. now to change window i turn my pc off. and change the red cable from drive to drive. now what i like to know is. if i connect the 2 red cable on the 2 drive do i get to choose window on boot up. or do i need a special program to make it work. now it is with 2 drive not a single drive .
View 9 Replies View RelatedHad vista & windows 7 dual booting & then i installed xp pro & lost my dual boot. How can i get it back?
View 9 Replies View Relatedi am new to this forum but i have problem with my system bootup. my system takes too long to boot and it started 3days ago. it takes about 120secs at bootscreen alone. i believe it is not my start up programs as it takes about 3 secs to start up from login page. i donot use any third party bootscreen. normally, my system boots in 30 secs but now i am facing a lot of problem which i do not understand. i have tried all the tutorials in this forum relating to bootup problems but found no luck.
View 6 Replies View RelatedI've upgraded my machine at some point in the last year, where I added a new 500GB drive and moved my C: partition across to it. The previous 250GB drive was left in for additional storage. Just recently (while upgrading my BIOS) I realised that my system was still booting from the 250GB drive even though Windows was on the other disk. There is a fair possibility in the not too distant future that I'll replace the 250GB disk with a larger disk, in which case I won't be able to boot. Is there a safe and reliable way to change it so that the system boots from the 500GB disk?
View 9 Replies View RelatedI'm using Vista Home Premium. I have a spare 250GB SATA drive, so I thought I'd install XP on that, then dual boot with my original Vista drive (AMD Athlon dual-core at 3 GHz, 4GB RAM, 64 bit Vista Home Premium...when it boots). The XP install seemed to go fine, in that the drive would boot up alone (with the Vista drive disabled). But when I plugged my main Vista drive in, the system would not boot up at all. I would get a Drive Read error. I don't get it. Both drives boot up fine by themselves, but when both are running, neither will boot. Do I need to set one drive's jumpers or something? I don't know SATA drive jumper settings, or if that's even the issue.
View 6 Replies View RelatedI am having some problems regarding booting up my Advent laptop, it came pre - installed with Vista home premium. it just wont boot up anymore all i can do is access the bios screen, the handbook it came with gives me information to press F8 to enter system recovery but sadly this does nothing, but make a beep each time i press the key. The laptop is just out of its 12 month guarantee so could be costly to repair. I wonder if any one can shed some light on what i can do to solve this problem.
View 4 Replies View RelatedI installed Vista Home Premium and got a nasty hard drive failure error. So I was going to boot from the install CD and get into the Recovery Options in order to run chkdsk on the drive. The system won't boot from CD. It actaully starts booting from the CD but after the loading files step it just boots into the installed Vista environment.
View 4 Replies View RelatedI have recently purchased Vista Business and it has been running OK for about a week with some assistance from Microsoft support. This morning I woke up and the system won't boot. I put the Vista disc into the PC and I get a page that comes up called "Install Windows" with 3 selections:Language to Install Time and currency format Keyboard or input method However my mouse and keyboard do not allow me to make the appropriate selectios or click the "next" button to continue.
View 3 Replies View RelatedI recently install new hdd 500gb seagate, i install windows vista home prem sp1 , when i try to boot the system IT FREEZED on booting on black screen and it shows all the hardware install when put any bootable cd and boot the system, system boots fine, i had same issue with old sansung 80gb hdd, i have to keep the bootable cd in optical drive to boot the system, i also tried reseat the cables from optical drive but did not work, my optical drive works fine after boot in windows
View 5 Replies View RelatedI've searched the web extensively, though I came close, I still can't solve my problem: When I've installed vista, the installation have set the boot manager to be on a different disk than the the boot loader. Now, if I want to remove the hard drive containing the boot manager, the system won't load, which is reasonable given these conditions, nonetheless I DO want to remove this hard drive and still be able to boot, therefore I've searched and queried everywhere and done the following: Physically disconnected the hard drive with the boot manager on it (d and boot with the Vista DVD to run startup repair -> this didn't help, the startup repair found the operation system but didn't recognize any problem, when trying to boot the system would not load, the error I'm getting when booting is disk read error occurred press ctrl+alt+del to restart.
View 4 Replies View RelatedI am unable to boot anything on my system. I have a black screen error File: pciidex.sys. When I try to use my restore disk I get a blue screen error Ox0000C1F5. I can not get into any of the Safe modes I just get the black screen error. And I am not able to boot the recovery system using PF11. It seems the only thing I can access is BIOS. I am not worried about saving files at this point. I really just want to restore back to factory settings and avoid needing to spend the money on a new hard drive. Any advise on how to re install with the errors I am receiving?
View 4 Replies View RelatedI have 3 hard drives with assigned characters c, d, f (e drive is cd rom) each drive has only 1 partition. On c there is Vista 32-bit Ultimate, on d there is Vista 64-bit home premium. If I change location of paging file - e.g. Vista Ultimate paging on f, Home paging on c then that operating system does not boot correctly. The OS boot progress bar is displayed but system does not boot (I waited many minutes before reset).
View 4 Replies View RelatedI've got a problem with my p.c in the fact that it wont boot up. I think i have unintentionally downloaded a virus which more than likey would have caused this. I have Windows vista home basic 32 bit pre-installed on my p.c and it didn't come with any back up/recovery disks. Any solutions on how to get my p.c up and running?
View 9 Replies View RelatedDoing some partition work a few days ago, and somehow lost the boot for my main system. D was my main system, as you can see it holds a lot of applications and information, "C" is a fresh install. Question is can I get "D" to reboot, it doesn't show in msconfig/boot. I know I can transfer bit by bit, but its a long winded job, I feel there must be a way to repair reboot. Tried the system disc Repair mode, only shows system on "C". 2 hard discs, "C" and "F" on one drive "D"on the other.
View 4 Replies View RelatedI have an hp desktop that came with vista home premium preinstalled. It will not boot up now. So I tried the emrgency recovery disks that I was told to createwhen I first got the computer and they didn't work. I thought I would have to boot from windows vista disks to repair this. No Vista disks came with the computer. My question is can I buy the upgrade SP1 disk to both improve the system and resolve the boot problem or am I forced to get the Full system
View 8 Replies View RelatedIm looking for information regarding the best way to configure a dual boot system using Vista Ultimate and XpPro. What is the best way to set up the two 320gig 7200rpm HHD's? Should both hard drive areas be combined and then partitioned or would you recommend one operating system per drive? OS are Vistax64 and XpPro.
View 8 Replies View Relatedannoying pop up when the system tray is being loaded at boot up. This is the message. SiSTray has stopped working a problem has arisen .windows will close this program down and if the problem can be resolved windows will let you know. The computer works fine after this window is closed down.
View 7 Replies View RelatedI have (or had) Vista Business on my HP Pavilion dv2670br and I also installed opensolaris on it. I had read this article (Vista SP1 won't install on dual-boot systems: Microsoft) before installing the SP with the stand alone file downloaded from MS's website, but since I did not have Enterprise or Ultimate I didn't think I would have problems. Silly me.
Now I do not know if it is the grub loader itself or the fact that opensolaris uses ZFS. I tried going through the steps here: Recovering the Vista Bootloader from the DVD - NeoSmart Technologies Wiki, to no avail. I suspect I will have to go through a very destructive process, but thankfully I won't really lose much since it is a relatively new laptop with very little university work on it.
I downloaded a film ( a backup o one of my DVD's it has got scratched and I really wanted to see it as well. Anyway when I did I opened up the video file into windows media player, it asked me to get some rights/ acquisitions to play the file. As the message was coming from windows media player I guess hmm it must be true. Usually I wouldn't if anything asked me to download anything. As it finished windows media message came up with a message to say it was downloaded correctly. So I checked task manager making sure it was actually windows media player and it was. When I tried playing the file it wouldn't play.
Whatever it downloaded hadn't taken effect yet. Then I blue screened. My laptop wouldn't boot up normally. So I tried booting up with " last good configuration" it booted up but I found out what had happened. All my programmes were "corrupted" something to do with the registry according to the 60 pop up messages saying each and every programme had been corrupted.........
I bought a new laptop with Vista already installed on it. I want to install XP in a multi boot configuration but get stuck in Disk Management and am unable to proceed from there. I'd like to keep Vista on my laptop, but if it comes down to it I'll need to take it off and put on XP because our work computers run with XP and we do a lot of work on reports and presentations from home and network from home. I can't find the New Partition Wizard to make a space for XP.
View 6 Replies View RelatedI have a laptop with a 320 gig hard drive divided into 4 partitions. I am dual booting Xp Professional and Vista Business 32 bit Edition. I plan on upgrading to Ultimate as soon as Microsoft ships it to me. I have 2 partitons for XP, 1 for vista, and 1 as a shared partition that has mydocuments and email settings so that both systems can access them. If I use Complete PC Backup and select all partitions will this backup everything ot a 500 gig external, including the boot records so that if I do oa complete pc restore it will restore it so that my boot menu is restoreed in the event of a hd failure? Also, when I get vista ultimate, I plan on using Bit Locker to encrypt my Vista partition. Will that affect the complete pc backup of that partition or any of the others?
View 4 Replies View RelatedI was reading the speed up boot time performance tutorial (by a now banned member, no less) and saw that it had an option to improve disk speed by enabling advanced performance for the disk. Is it wise to do this on an installed hard drive? I noticed the optimize disk option was already enabled on my C drive and was wondering if it would be a good idea to enable the advance performance option as well.I just don't want to lose information if I am forced to, say, hard boot the system when if it freezes up.
View 4 Replies View RelatedI have a dual boot system: XP PRO on drive C and Vista Home Premium on drive B. I want to replace my hardrive, and move (or clone) Vista to new drive and be it C drive. Vista is still virgin and not other programs are installed, so changing it location from D to C drive will not influance any applications. I know how to create hard drive image. My question is how to make that new c drive with Vista on it bootable again.
View 4 Replies View RelatedI have a newish laptop wunning vista home basic which crashed. It wont boot up I have tried chkdsk which found no problems, the windows repair thing cant diagnose the problem and it still wont work.
View 8 Replies View RelatedI have Acronis True Image and before I went the dual boot system route (XP + Vista x64), I made an image of my XP system but now that I am comfortable with both OS's, I would like to know if Acronis can make an image of my drive including both systems?
Before attempting to do this on my own and botching the already good image I have, I would like to hear it from the Gurus so... what say you? Oh, also, I have heard that Acronis can do this but nobody specified if I should start Acronis in Vista or in XP and that is another thing that baffles me. It shouldn't matter where I start the image process but making sure is my first priority since I tend to screw up things fairly quick when I go out guns blazing (so to speak!)
I have a dual-boot setup. Volume C runs Vista Home Premium. Volume F runs Vista Ultimate. (Vol. D is a recovery volume.) I would like to blow away C: and boot only from F. Would the following be a possible/advisable solution?
1. Boot from F.
2. Delete C.
3. Rename F "C".
4. Expand F (the new "C") to include the old C.
I'm using HD from my old computer (XP) as an external drive on my Vista laptop. The HD has XP on it. When I power up it looks like the HD is trying to boot XP on top of my Vista and freezes the system. How can I avoid this attempted boot? Where should I place the jumper on the HD.
View 8 Replies View Related