Repair Install: Interfere With System's Ability To Multi Boot?
Jun 29, 2008
I partitioned a new hard drive and formatted it using my Windows XP Home Ed. SP2 Install CD. I then installed Win XP. I then installed Windows Vista Home Premium 64 bit on the other partition. ( I have two partitions on a single drive, C: and D This has been working great for me for the last 5 months. Today I have a reason to perform a repair install on just the Windows XP partition. I have performed a Win XP repair install successfully in the past using the XP SP2 install CD but never when my system was set up as dual boot. If I perform a repair install using my WinXP install disk to repair the Windows XP installation, will this leave my Vista partition untouched? Will it at all interfere with the system's ability to multi boot? I'm not very concerned about not being able to boot up into Windows XP but it's extremely critical that my system's ability to boot up into Vista is not compromised.
I bought a new laptop with Vista already installed on it. I want to install XP in a multi boot configuration but get stuck in Disk Management and am unable to proceed from there. I'd like to keep Vista on my laptop, but if it comes down to it I'll need to take it off and put on XP because our work computers run with XP and we do a lot of work on reports and presentations from home and network from home. I can't find the New Partition Wizard to make a space for XP.
I bought a new laptop with Vista already installed on it. I want to install XP in a multi boot configuration but get stuck in Disk Management and am unable to proceed from there. I'd like to keep Vista on my laptop, but if it comes down to it I'll need to take it off and put on XP because our work computers run with XP and we do a lot of work on reports and presentations from home and network from home. I can't find the New Partition Wizard to make a space for XP.
I accidentally put vista into sleep mode. The video was all garbled and it was clear there was an issue. So, I hit the reset button on my tower to stop the mess. My next boot I got the error.
File: Boot/BCD
Status: 0x0000001
Info: An error occurred while attempting to read the boot configuration data. It says to put in the windows installation disk and "click repair your computer." The issue is when booting to the DVD, on the page with the moving green bar and it says Windows Vista under, it hangs. I even left it there for 2 hrs. The HDD LED on my computer is solid the whole time too. All my hard drives are SATA and they are in AHCI which is turned on in the BIOS. Perhaps changing the drives to IDE would help?
Anyways, Id like to get into that repair CD so I can fix my boot sector so I dont have to reformat. This has happened before and Ive had to reformat. Im sick of it, I dont want to reformat Vista again. Incase you didnt already know Im using Vista Ultimate x64.
I would like to try a system repair but when I put my windows vista premium disk into the dvd player it only gives me the option to install and not repair. How do I go about getting the repair option?
MY HDD lists the order of my partitions as D:, C:, and E:. I have Vista 64 set up on C: and 32-bit on E: to experiment with each. D: is a recovery partition. I'm thinking of removing the data from E: and deleting it and then "Stretching" C: back to it's original size. Best way to do this?
Has anybody installed Vista twice in separate disk partitions on the same PC? I've been successfully running multi-boot with 2 XPs and a Vista on 1 PC. There's plenty info about on how to do that. Now I'm going to separate all XP installs onto 1 PC, and all Vista installs onto another PC. Will this make life easier? So I'll be running Vista Home Premium twice on 1 PC. One install will be for production use, and the other for testing. I've not seen any info on doing this.
I have (or had) Vista Business on my HP Pavilion dv2670br and I also installed opensolaris on it. I had read this article (Vista SP1 won't install on dual-boot systems: Microsoft) before installing the SP with the stand alone file downloaded from MS's website, but since I did not have Enterprise or Ultimate I didn't think I would have problems. Silly me.
Now I do not know if it is the grub loader itself or the fact that opensolaris uses ZFS. I tried going through the steps here: Recovering the Vista Bootloader from the DVD - NeoSmart Technologies Wiki, to no avail. I suspect I will have to go through a very destructive process, but thankfully I won't really lose much since it is a relatively new laptop with very little university work on it.
I had successfully installed win xp pro on my pre-installed vista home computer.
When I used to boot up, I had the option of selecting one of those 2 OS. I begun having problems with xp pro so I "repaired" it using my xp pro cd. Now, I can't boot into either OS. Please help. I have tinkered with the MBR, FIXMBR, FIXBOOt commands but can't get anything to work. All I get when I boot up is the selection of Keyboards, language and then I get a menu of options such as Repair startup, Memory diagnostics, Recovery (to factory settings) etc., I don't have vista dvd since it came pre-installed on my computer.
I do have xp but am afraid of re-installing xp pro since I have documents on borh drives (each drive contains its own operating system).
For example, my c drive contains vista, (d is recovery on the same hard drive) and xp pro is on a separate physical drive.
I can see that both drives have windows on them but I am unable to boot. I have managed to get vistaboot pro but can't seem to run it.
I have Vista Home Premium 64-bit and Windows 7 installed and use the standard Microsoft boot manager from Windows 7 to dual boot. Each operating system is in the first primary partition of a hard drive. No problems. However, I think I need reinstall WinXP so that I can view some old AVI files that use the Intel IV50 codec. For some reason Vista does not like the AVI files and best I can tell the codec add-in only works under WinXP Media Player. What is the best way/program that will allow me to boot either Vista, Windows 7 or Windows XP OR is there a magic bullet to view and convert the old AVI files. I have tried Format Factory and come up empty. No matter what I try the audio works but the video is not available.
I recently got a new Vista machine - not because of a desire, but because of it becoming necessary. Anyhow, I have taken the steps to establish a network and have assured that the same network ID is on all computers. The several operating systems include Windows 98, XP Home Edition, and Vista Home Premium. The Vista Machine is set to private network status, set to share files and folders, set to share printers, set with Password Protection turned off, and set with Neetwork Discovery turned on. I have also gone to the folders that I have set to share on the computer (the C drive, among others) and have made sure to set the permissions so that "Everyone" has full access and control.
Lastly, I have set-up the system to disable User Account Control. Per Microsoft, everyone who has a computer associated with the network should be able to freely acces, read, and write to the files, printers, etc. that I have shared on this computer, right? On the network maps on all computers, all computers are visible. Furthermore, once a computer on the network is selected, the shared items are usually visible. But, for some reason, no computer can access the shared materials on the vista machine even though from the vista machine, I can access all shared materials on the other computers. When the shared materials on the Vista Machine are attempted to be accessed, a "Access Denied" Error/Alert is displayed. I have restarted all computer AND the router to no success.
I made an attempt to add ubuntu the other day, it semi took. When I tried to boot to it today, there was nothing there. But.. There was a screen with many different options on how to boot, repair, diagnose etc.. Tools everyone needs but can't access. I don't really want to re-install ubuntu just to find all those utils. Is there another way to get a boot repair screen with all the different utils on it?
No problems whatsoever for 6 months until Monday night black screen with blinking cursor. Rebooted. Got the message saying cannot start up normally.. disk may need synchronizing (can't remember the exact wording of any of messages)
1. tried to run chkdsk. hung for HOURS. 2. tried to run repair thingie from vista disk. that says it may take an hour or more but i gave up after 6 hours. 3. tried booting into safe modes. does not boot past crcdisk.sys 4. used vista disc again. said i cannot restore to an earlier point because of disk errors. was able to run cmd prompt. all my files are still on the C: moved some files to external drives without error using the move command............
I have a Dell Dimension E520, which won?t boot to Windows (Vista), and none of the repair options work:
Startup repair Reports repair fail due to problem with registry
System Restore Reports no restore points available
Windows Complete PC Restore Reports no backups available
Windows Memory Diagnostic Tool No memory problems
Command Prompt. Can?t think of any appropriate command to use here. So I booted with the system DVD (as one would with XP) but the upgrade option has been greyed out. I don?t want to do a clean install. I want to repair the existing installation.
i'm using Vista Ultimate x64. But i have the bootcd error, The problem is: I can't do startup repair there are no OS listed! I click laod drivers than windows explorer thing comes, but what than? I must choose a Setup Information File or something, I accendentally deleted the Boot/bcd map, i just wan't repair, just no OS listed, i can't find it! (i can see my hard drivers)
I have an Acer Extensa laptop with Windows Vista Home Premium installed. Its been working great for over a year now untill yesterday when all of a sudden it wouldn't boot up properly. It continued to go to start-up repair, but that kept on failing. After trying all other tools, (system restore had no restore points for some odd reason)... I tried safe mode. That did not work. It instead went back to the start-up repair screen. The same warning message popped up everytime it failed "Cannot repair automatically, click finish blah blah blah". When I bought this laptop from Best Buy, I did not recieve any type of Disk for Vista, it was already loaded on there... I would rather not do a clean install.
I start or restart my computer I have to insert my OS disc to repair it because Vista wouldnt boot. Its Vista 64 premium. I have been trying to figure out why and I am at a loss. I uninstalled and removed my tv tuner and driver. I restored it to an earlier point. Is this a common problem?
Start up repair problem signature reads as follows: Problem Signature: Problem event name: StartupRepairv2 Problem signature 01: AutoFailover Problem signature 02: 6.0.6000.16386.6.0.6000.16386.....
When I boot at the Thoshiba screen (options to boot into setup/multiboot) there are green lines going vertically through the screen. It will not boot if that is the case. It then initializes start up repair which gives me the error above. I have tried to restore from earlier points to no avail. I have reinstalled vista from my disks at which point it worked for a minor peroid of time and this started to happen again. Virus? Once In awhile it will boot without the green vertical lines and will start up just fine, but this appears to be random.
My 8 month old (64 bit) Acer laptop will not come up to a menu screen. I turn it on and it goes to Startup Repair screen. It searchs for problems, but then tells me it cant repair computer automatically. I know very little about computers, but after a little research I am sharing the information below in hopes that some kind person can provide insight. Stupidly I had not Backed Up in quite a while and I cant get to a recovery point.......
I have an HP notebook with Vista Home Premium and after running SFC I have a few corrupted files.
Question is there a way to bring in the original files when the OEM didn't send an install DVD or will offer one at all?
All I have is the recovery partition with the option to "repair to original factory condition" which from what I gather means erasing all my settings and personal files.
I have made a recovery disc (from the partition) and I have the "Anytime Upgrade DVD," and I'm curious is there any way to access the upgrade DVD to get to those files or even do a real repair of Vista without losing settings and personal files?
In wanting to do a repair install (keeping existing programs etc), on running Recovery CD, I get the message.
"Upgrade has been disabled vand cannot be started. To upgrade, cancel the installation and then choose to upgrade to a version of windows that is more recent than the versiopn you are currently running"
I'm running Vista Home Premium (fully updated) but suspecting that I may have a problem, I thought I could do a repair install but it seems all I can do is either a clean install and thus lose everything or upgrade to I assume Business or Ultimate Editions of Vista. Why can't I do a repair install from Vista Recovery CD?
I have a PC that had XP pro installed 1st. Then I installed Vista using the dual boot option on the vista DVD. Everything went well and it all worked fine. I've been happily using Vista for months now, and I've not used XP for some time. But now I need to use it, and it won't boot up.
It gets as far as the log in screen. But the keyboard and mouse don't work. (they do during boot up as I can use the keyboard to choose the OS). Same thing in safe mode. How can I repair the XP installation (or do a new one from scratch), with out messing up the Vista installation and keeping the dual boot option.
I am running Vista Home Premium and want to do a "repair install." I have an OEM DVD with Vista. I have performed the repair process in the past (I think it was called Upgrade), but now that I have installed SP1, it won't work. I slipstreamed a DVD with SP1 according to the tutorial, but it still indicates that the existing version of Vista is newer than the one on the slipstreamed DVD and says that the upgrade functionality is disabled.
I noticed on the tutorial that you need a Retail version of Vista to slipstream with SP1. Is the OEM version different than the Retail version? Is that why I cannot do a Repair Install?
Having found out I need to remove SP1 before I can do a repair install, is it possible to slipstream SP1 with the recovery CD to create a new one in case I need or to do a repair install in the future
I restart it and it doesn't want to start up and it just keeps trying to repair the startup. This then stopped, for the next couple of days all it was doing was going past the BIOS then a black screen with a blinking cursor would appear and it would never boot. Im pretty much sure that it came with Vista preinstalled on it so I dont have a vista CD, I tried the recovery Cd.
Now everytime i restart it it gives me options for safe mode etc I have picked them all and it loads fr a bit then the screen goes to a page with text saying reinstall windows and the registry is corrupt. Info: Windows failed to load because the system registry file is missing, or corrupt. Now I cant get into any of the safe modes at all and I dont have a vista CD as it was preinstalled.
My Laptop is a Toshiba P200 satelite it came with a OEM Recory DVD is one of those DVD that you supose to run automatic and it then Wipe out everything and clean install it acording to Toshiba thats the best way of doing it.
But what if i just want to repair some System file I have a Corrupt Msdos when i acess it by running "Command" in start/run and Msdos open I can only navigate the drives by typing Cd c:/ cd... etc. But as soon i try to run something else lets say Type DIR in C:/ it Freezes as soon i press Enter (i see a cursor blinking up and down and dont let me do anything)
I am sure some Msdos files must be corrupted or missing and the solution is to restore those files repair vista. Do i realy have to Clean install Vista everytime because Toshiba havent included any repair disc only a Full clean installation DVD?......
Iv had my PC for around 4-5 years now and everything has always worked perfectly with windows home basic 32Bit, however yesterday i went to boot my PC up and it seemed to get to the stage where windows attemps to load up and it stayed on the same stage for 10mins or so, so i reset the PC and it came to a page saying something to do with look for problems and one saying cancel, I have tried the system repair a number of times but nothing seems to be happening :S Ive heard that a way of getting around the problem is to use the vista installation disc, is this correct?
I had to install a new Motherboard. The CPU, Hard drive and all the other hardware are the same. Is there a way to get Vista working again without doing a totally new installation of Vista and all other programs?
a lot of the free partition managers get you to the point of "next time you boot you will get this error, just put in your Vista install CD and do a repair" yadda yadda. What about the millions that don't get a CD when they buy a PC? Got to be some way to fix the bootup stuff without restoring an entire image.
I have Vista Home Premium 32-bit, on Dell Inspiron 6400. After a repair install, I now have two problems: - Although there are 75 Windows Updates in the list, I have tried several times over the last two days to install these. So far, only a few are marked "Successful". The great majority are marked "Failed". - There is no SP1 available in the list of updates.
Here is the history:
- My laptop was pre-loaded with Vista (no SP1). The OEM DVD was also SP0. - I installed SP1 when it became available. - A few days ago, I neede to do a repair install. So I uninstalled SP1, and did a repair install as specified in Brink's tutorial: Repair Install For Vista - As far as I know, the repair completed successfully. There were no "Files discarded by Windows Upgrade" (Maybe this is important!). I was not asked for my product key, or asked to activate Vista. - Immediately after the repair, I launched Windows Update, and found the two problems noted above.
BTW: To the best of my knowledge, my laptop is working fine. The minor glitches that prompted the repair install have disappeare.
