I have just purchased an Acer Aspire 8935g laptop, which comes with Windows Vista Home Premium 32bit (not sure why 64bit isn't supplied). It has two 500gb hard drives; Disk 0 and Disk 1. Disk 1 is empty and I have successfully created 3 partions on this drive. According to Vista's Disk Management tool, Disk 0 contains three partitions. The first and last are both EISA Configuration partitions and can't be seen through Windows Explorer. The 2nd (middle) partition is the C: partition on which Vista is installed.
I want to install Windows 7 RC 64bit in a dual boot configuration, so I used Disk Manager to shrink the C: partition and then create a new 100gb partition. I assigned it the drive letter B: (there are no floppy drives on the laptop). The new B: partition is visible, along with the original C: partition through Windows Explorer, until I reboot the laptop. The B: partition then disappears and Windows Explorer can no longer see it, however Disk Management shows it is still there but it no longer has a drive letter and is now an EISA Configuration partition. I thought this issue might be caused by the choice of drive letter so I tried again using a different letter (F. Each time the drive is only visible to Windows Explorer until the laptop is rebooted. I've also tried using a different partition management tool (Partition Wizard) but it makes no difference. I've tried creating the partition as logical and primary but to no avail.
I have just purchased an Acer Aspire 8935g laptop, which comes with Windows Vista Home Premium 32bit (not sure why 64bit isn't supplied). It has two 500gb hard drives; Disk 0 and Disk 1. Disk 1 is empty and I have successfully created 3 partions on this drive. According to Vista's Disk Management tool, Disk 0 contains three partitions. The first and last are both EISA Configuration partitions and can't be seen through Windows Explorer. The 2nd (middle) partition is the C: partition on which Vista is installed.
I want to install Windows 7 RC 64bit in a dual boot configuration, so I used Disk Manager to shrink the C: partition and then create a new 100gb partition. I assigned it the drive letter B: (there are no floppy drives on the laptop). The new B: partition is visible, along with the original C: partition through Windows Explorer, until I reboot the laptop. The B: partition then disappears and Windows Explorer can no longer see it, however Disk Management shows it is still there but it no longer has a drive letter and is now an EISA Configuration partition. I thought this issue might be caused by the choice of drive letter so I tried again using a different letter (F: ). Each time the drive is only visible to Windows Explorer until the laptop is rebooted. I've also tried using a different partition management tool (Partition Wizard) but it makes no difference. I've tried creating the partition as logical and primary but to no avail. explain Why can't I create a visible partition on my "O/S" drive?
I'm trying to partition drive C but it won't let me. New laptop is Toshiba Satellite and had the store configure it for me since I'm new to Vista.
1. Through Disk Management, I shrink drive C and now have an unallocated space of 51G.
2. From the unallocated space, I create a new simple volume. It goes through the Wizard, but then I get the following error message: "The attempted operation is invalid. Either the parameters specified are invalid or the operation cannot be completed on the selected object."
3. The contour of the unallocated space is highlighted in black instead of green. Is that an indication of something? And shouldn't it say: Free space instead of unallocated? Additional info:.....
I recently purchased a HP M9200t with Vista Premium 64 bit. I would like to make the hidden recovery partition, visible. I want to keep it, but I also want to create a folder for updates. How do I make this partition visible? I remember a registry entry mod, but I can't find it. And, it should be for 64 bit Vista.
i just got a new comp and i had vista installed and i made a xp partition but it was buggy and i couldnt boot into both so i figured id do a clean install so i completely erased my hd from dos at vista install screen and now i have 1 700g drive that says disk 0 unallocated space and when i click next i get a error saying.
Windows could not create a partition on disc 0 This error occured while preparing the systems volume files. error 0x80042558. i cant create a new partition either i get new message. so right now ive got a new comp with no OS and a 700 gig free HD that i cant install vista on. i havent tried xp yet trying it tomrow or whenever i get the disk but idk what to do.
I just tried to create a new primary partition using Disk Management. I get the error "You cannot create a new volume in this unallocated space because the disk already contains the maximum number of partitions." Ultimate goal is to create two more bootable partitions on my hard disk, one for Windows 7 and the other for Ubuntu. My C drive contains Windows Vista, my D drive has program files, and my E drive contains data. According to what I found online, you can have up to four primary partitions on a disk.
I recently had to change my hard drive because the original one got bricked. I was wondering how to make the recovery drive that was on the original HDD.
I have a Gateway Desktop 1tb hdd and would like to create restore partition the way Gateway would have created it when it left the shop. I believe the create a 5-10 Gg partition with a picture of what the machine look like (vanilla).
Can any one tell me how to do this myself or point me to instructions? My think it that it might be as simple as using say, Acropolis to create a full backup to this 10gg partition.
However, I'm thinking when Gateway does this in its shop it uses something else that is not reliant on a specific manufacturers software when I recovery/restore if required. What might Gate use to create a Restore Partition?
I recently purchased a Vista Home Premium upgrade package and I want to upgrade by OEM version of XP (Media Center) shipped on my computer. I must also maintain XP on a dualboot partition for legacy applications compatibility issues. My plan is to do a clean install of Vista Premiun updrade, then use Virtual PC to create a virtual XP OS partition using my OEM XP disk. My question is, will this: Does this create a license issue?
I downloaded Windows 7 RC1 with the intent of adding a partition to my HDD and dual booting. My understanding is that I would need a 16GB partition. My Disk Management Console tells me I have two existing primary partitions (expected). D (the recovery partition) is 6.62GB. The other (C) makes up the difference (~142GB) and has 47.1GB free space. When I begin the "shrink volume" process, it says that only 3MB is available to shrink C. I checked the page file and it has less than 3GB allocated to it. So, I have two questions. First, why isn't more shrinkage ;>) space available? Two, assuming that with your help I can find more space, if I try to create a 16GB partition from C will I significantly affect computer performance?
I'm running Vista Sp1 and am frequently using VPN connections to our clients. All of a sudden, I'm unable to create a VPN connection. If I look in Event Viewer under administrative events, I read the following message: 'The initial Secure Socket Tunneling Protocol request could not be successfully sent to the server. This can be due to network connectivity issues or certificate (trust) issues. The detailed error message is provided below. Correct the problem and try again. The certificate's CN name does not match the passed value.
I am having printing problem on my Vista business machine. I have a printer server (Windows 2003 server Domain Controller), and the new Vista is joind to domain as a standard user. When I add shared printers to the Vista, it prints out without problem. Problem is, however, after I restart the Vista, I am getting this error messages everytime I tried to print test pages. "Test page failed to print. Unable to create a print job".
Vista 64bit has been running really well on my desktop after a clean install in March. Suddenly, Windows update is failing to install, because it can't create a systen restore point. When I try to create one in System Restore, manually, it fails also, citing the shadow file timeout, or some such.....I am worried, because I can't use backup, either! Anyone know what's going on?
when i tried to create a restore point an error message is being displayed. it says " could not create the scheduled task for the following reason task image is corrupt or has been tampered with (0x80041321)" what does it mean. i am running on vista ultimate x64
pc config dual core 2.8(intel) intel 965board 80gb hdd
what i did was under system properties page, i clicked system protection tab on the left side checked the boxes( all system drives ie hard disk drives) and clicked apply then the message i described was popping out and when clicked create also the same message is being displayed.
I have been using Windows Mail for my Yahoo addresses and by right clicking on the W.M. icon in the programme list above the start button I put a shortcut on to the desktop that has been working very well. Today I have combined Yahoo and Hotmail addresses under the WLM umbrella. But I cannot find how to make a shortcut. Nowhere can I find the relevant WLM icon to make a shortcut from. Obviously I am missing something, somewhere, but what is it?
My Windows Vista Enterprise has a serious problem. It is unable to find, delete, or create any system restore points. I have not found a way to re-initialize the system restore point process.
I am having some problems with my drivers so I am trying to delete the partition on the operation system drive and do a fresh install, operating system and drivers. However, no matter what I do I cannot get my computer to boot from the windows vista DVD so I can delete the OS partition. Here is what I already tried:
- My BIOS is set to boot from CD ROM first
- I have tried both DVD drives
- I verified that the DVD is good by trying it in a different computer where it will boot from the DVD drive
- The DVD drive works because I can initiate installation from the DVD drive. But since it isn't on start-up, I cannot delete the partition and all the drivers.
How do I get this dang computer to recognize this DVD on boot?
I have -Dell XPS 730x with 6 GIG DDR3 RAM, Intel i7 64 bit Processor, 500 GIG disk,
I am running -Windows Vista Home Premium 64 which was preinstalled on the cpu
I want to -Dual boot between Vista64 and Windows XP32
So far -I have done everything to this machine from creating a virtual window in Vista64, to going into the command prompt from vista boot disk and running diskpart to clear hard drive.
I currently have -Two partitions on one disk. Primary 200GIG and Healthy 265GIG -Windows Vista Home Premium64 installed and running
The problems im having -every time try to boot from CD and run the windows xp setup, it is UNABLE to find ANY HARD DRIVES!
I have researched that - I must have the disk partitioned - Windows XP must be installed first - I have to play with the boot.ini - If i install vista32 it will be more successful
The errors I have gotten -STOP: 0x0000008E - i researched this and it said one option is to take out the excess RAM
I will be happy if - By the end of this weekend I can successfully run XP or both OS's in dual boot.
I need to go through all this trouble because - Digidesign has not written software for 64 bit proccessing yet. I need to make music.
A customer asked if he created the recovery disc would he still have a complete working recovery partition. He is in fear of creating the disc then losing them.
I was tweaking my graphics card with Nervia and i was changing some options and now when i go into GTAIV it crashes say GTAIV FATAL ERROR "unable to create depth render target. please reinstall DriectX or install the latest video card drivers" i have tried switching everything to the defaults and i uninstalled it. i have updated my Direct X to the latest version and i am downloading the latest grapics drivers from Nvida
I am running Windows Vista Home Premium 32 (system specs: laptop 2.1 Ghz core 2 duo, 4 gb RAM, 500gb hd (about half full) nvidia 8400M GS, Avira Premium Security Suite). I have had the computer for about a year running fine with 1 main admin account. Now when I need to create an account for another user I cannot create one, either admin or standard. When I create it, using either the control panel or command prompt, it creates the user picture, making the account visible on the control panel user accounts screen, and on logon screen. However, when trying to log into the new account I am greeted with the error "User profile service failed on logon. User profile cannot be loaded." The standard fix for this from various forums is to edit the registry key of the account. However, on going to regedit I see that no key even exists for the account. On further investigation I discover that no user files have been created either. I attempted a system restore, but discovered that all my past restore points were gone, and intruigingly, the computer had stopped createing 24 hour checkpoints. I cannot say for definite whether it was this issue or another one that caused system restore to mess up, as I don't check my system restore all that often. Either way, system restore is not an option. There have been mentions of a full Vista reinstall, though if at all possible I would like to avoid this.
I am having problems with creating shortcuts on my desktop. when i select send to desktop (create shortcut) it comes up with the error. Windows could create the shortcut. Check to see if the disc is full.I have over 180 GB free space left. To get things to the desktop i can drag it into the tab section next to the start icon, and then drag onto desktop.But when i do this i am always required to give permission and it creates two desktop icons.i have been having problems with my catalyst control centre but i dont think they are related.
When I install Vista, it wants to force me to create a local account, and it won't let me create one called Administrator, becuase the name is already used (thus the Administrator account exists). I don't want to create some dummy account just just to log in to join the domain. How do I get past the "Choose a user name and picture" screen and log in as Administrator so I can just install the network drivers and join my domain?
Whenever I view a folder (stored on a CD) with photo files using windows explorer it does not show the small pictures. Instead the standard windows icon/picture is shown. The pictures are visible for a short moment and then replaced by the default windows icon picture. This problem does not occur when I via a folder with photo files located on the harddisk. I use Windows Vista home premium (dutch version)
since few days i have been seeing a straight line visible near the gadget column.. and whn i open explorer or internet explorer, tht line is visible, does anyone have solution to gt rid of the line? attaching a picturee...
I am new to Vista but not Computers. In C:Program FilesCourse Designer 3, I created a new sub-folder '2008'. In Windows Explorer, this folder is not visible. In Windows Mail, it is. In the actual Course Designer software, it is. Why can't I see it in Windows Explorer?
