Changing Boot Drive
Jan 8, 2006
I recently purchased a new hard drive and used the software that came with it to set up the new drive as the boot drive and the old drive as the slave. However after installation, it still shows the old drive as the boot drive and the new drive as the slave.I have set the jumpers to "master" on the new drive and slave on the old drive. Is there any way to change this? I dont know what else to do siince the jumpers are set correctly. running winXP home with Dell Pentium 4.
View 4 Replies
ADVERTISEMENT
Jun 24, 2006
I just upgraded to a 300GB hard drive from a 250, which I will use as a backup drive. However, when I set it up, the primary boot partition got set up as D:. I have 5 partitions on this drive. The others were also mislabeled, but I could change them with the Computer Management tool. There is no C drive on this system. I want to make what is now D become C.The original also had 5 partitions. All I wanted to do is duplicate the old drive to the new one. Somehow, the boot partition became D and I can't change it from within Windows. Is there a way to do that? I have created the UBD for Windows using Bart's PE, so I can boot the machine independently of using the hard drive. If I can use that, is there a tool there or a command line program I can use to change it?
View 2 Replies
View Related
Jul 8, 2008
I have a hard drive that comes with my PC and that has a corrupted Windows, but the boot.ini still works fine. So I got a new hard drive and installed a new fresh copy of Windows XP on it. So now I want to format the old hard drive and use the new hard drive as the boot drive. However, if I removed the old hard drive, the new hard drive doesn't boot at all. I've tried using the FIXMBR, FIXBOOT, and BOOTCFG /REBUILD commands, but I think I did it wrong.
View 4 Replies
View Related
Dec 3, 2006
I was doing a new installation of XP home on a new hard drive, XP formatted the drive as F: and installed the boot sector there because a thumb drive was in the usb port (which it recognized as C:). I wasn't paying that close of attention and I didn't realize XP would see that thumb drive as C:. My question: is there any way to change the boot letter back to C: without reformatting the hard drive?
View 3 Replies
View Related
Sep 5, 2009
I was running windows on an IDE hard drive and bought a new SATA and installed a fresh copy of windows on it, now having a dual boot with the old installation on the IDE. I've been running on the SATA drive for a few months now and I want to remove the IDE drive from my system but when I disconnect it and reboot I get a message that tells me NTLDR is missing so I am assuming that the boot record is on the IDE drive. How can I make the SATA drive my main boot drive?
View 2 Replies
View Related
Feb 22, 2006
I changed my boot option using msconfig to safe mode. But I didn't realize I needed a local username/ password to login. So now I don't know a local username password and pressing F8 and specifying Normal mode still boots in safe mode.
View 14 Replies
View Related
Jun 19, 2006
I have a friend who's motherboard was fried and he also had to change the power supply. He brought it to a computer shop and they diagnosed and told him to replace the two. He replaced it and now it will just boot pass the memory test and before the windows screen comes up saying windows xp loading, the blue screen of death comes up for 1 second and restarts, this process continues to occur. I heard you can try to run the repair but he also needs the cd key or install xp right over with the same key. Unfortunately I don't have the key. I heard you can run the recovery console and fix it but I'm not to sure exactly how to do that and wouldn't mind a little help with some step by step instructions. It has to do with the HAL.
View 12 Replies
View Related
Jun 4, 2005
I reinstalled Windows XP and accidentally installed it on my D: drive. Now I want to change the system folders, prog files, etc and make the C: drive my default one. Is there any way to do this WITHOUT having to reinstall XP again?
View 1 Replies
View Related
Jun 3, 2008
I created a new partition and installed Windows on it a while back, but when I booted up, it had the letter G and my other partition that I used to store music was drive C.I was going to change drive letters around so that my OS was on drive C, but I was wandering if this would mess up any applications I have on the system?
View 4 Replies
View Related
Jan 30, 2005
i feel that this is probley simple... but I don't know how to do it. I've right clicked directly on the dvd-player to see if I could change it and nothing is there. My dad has a dvd-player F: and a cd-rom drive E:, His computer was formatted recently, but now the software for each of the drives are mixed up. Putting a dvd in drive F:, tells us that drive E: does not contain a disk.I would like to just change the drive letters back to how it wants to be set-up.
View 1 Replies
View Related
Nov 22, 2006
i am dual booting xp mce and vista.. and im wondering if its possible to change the displayed names because xp shows up as "earlier windows version" or something like that and i'd rather it just say xp
View 5 Replies
View Related
Jul 7, 2005
I recently attached a new dvd rom to my pc. After it was detached, the drive letters on my extra HDD's have changed around.Can anyone please explain to me how to change the drive letters back?
View 6 Replies
View Related
Dec 30, 2007
I got a usb flash drive and plugged it in for the first time today. My computer automatically named it (F and (G - it had two partitions apparently. Anyway, I also have a Buffalo external hard drive that was always (F before. I figured my computer just assigned the usb flash drive (F and (G temporarily because the external hard drive wasn't turned on. So when I did plug it in, it was named (H. However, when I disconnected both drives, and re-plugged the external hd, it was still (H. Also, I noticed that all my folder settings in the external hd were reset.
I tried uninstalling the driver for the usb flash drive and the external hd remained (H.
Is there anyway to reverse this without reformatting or otherwise damaging my files inside the external hard drive
View 2 Replies
View Related
Jan 31, 2007
So I just ran into a problem with my External Western Digital Hard Drive. Previously, my drive was mapped as the E Drive (I believe) and after taking it down and setting it up again (when i moved back to college), my external hard drive switched drive names on me. This really sucks, as my external drive stores all of my iTunes music and now when i run iTunes, it tries to find the music from the E Drive location and not the G Drive location. Is there an easy way I can change the letter drives so that I don't have to reimport all of my music?
View 1 Replies
View Related
Jun 20, 2010
I wanted to install Windows XP on an old computer. Its CD drive was broken, so I installed XP from its hard drive instead. When everything was finished, I ended up with two drives, D and E. Unfortunately, I was tempted to change the letters (OCD, much?) to C and D, and did so (via regedit).Now, my computer won't boot up; the welcome screen shows up, but it freezes there.
View 10 Replies
View Related
Nov 9, 2006
I have been using a Compaq Deskpro with Windows XP SP2. And then I sold that computer and bought a Compaq Evo. I then inserted the same harddrive but it is failing to boot. When I insert the installation disc it says "Press any key to boot from CD". Pressing keys does not activate anything and it stays on the same screen. I then created 6 set up disks and they all work perfectly loading drivers etc. The problem starts when I reach the stage where it says "insert Win XP SP2 installation disc and press any key when ready". Pressing the keyboard keys produces no response
View 7 Replies
View Related
Mar 26, 2007
I am running XP Pro on a rebuilt Dell PIII. The original hard drive is 7G, so I added a 300G slave for storage. My plan now was to change the 300G drive to the Master drive. I reformatted, booted from my XP disc & installed the OS on the "new" 300G drive. Then I switched the jumper & cable so it was in the master position.and nothing.
It starts up, tells me to hit F2 for setup or F1 to continue. When I hit F1, it goes to a blank screen with flashing cursor, but no command line
View 9 Replies
View Related
Dec 21, 2004
I'm having trouble when I enter my BIOS. It seems that once I enter, I can't move up or down or do anything at all. At first, I thought it migt be my keyboard, but I switched my keyboard with the keyboard from my other computer. It still had the same problem. I don't know why my BIOS won't let me do anything. Can anyone please help? I just want to change the boot sequence so I can wipe my drive
View 10 Replies
View Related
Oct 8, 2008
I recently installed a new hard drive into a friends computer and installed XP Home.
I ran all the updates and service packs.
I left later that day and let him install all his applications.
I got a call tonight from him saying he really screwed up and doesn't know what to do.
I had to follow his thinking over the phone so I hope I get this all correct.
He had trouble loading the drivers for his HP printer. He would get an error saying that a C: empHP_WebRelease folder was missing. He did manage to figure out that for some reason when I installed XP it called the Boot drive "I" instead of "C"
View 1 Replies
View Related
Sep 19, 2007
I have an old HD From a system that I got rid of. I want to put it into a friends system to see if I can retrieve the files off of it and put it onto my external HD. The hard drive was the boot disk and the computer I am installing it on has it's own boot disk. If I boot up with two boot disks will there be a problem? Is there anything I need to take into account before doing this? I am planning on installing the old HD onto an ATA cable that I unplugged from the DVD drive. The HD that is in this system is not on an ATA cable, I'm not sure what it is connected to, just a small plug with a blue cable going to the mother board.
View 3 Replies
View Related
Oct 3, 2010
With the help of CNET my computer is back up and running, but I need more advice now. I formatted the hard drive to get rid of a trojan, and reinstalled stuff. Previously I had changed MY Documents from C Drive to D and made it the default, and I can't remember how I did it, I should have written it down!!
My netbook is a Wind, 120GB HD 1GBRam, intel processor, XP SP3
View 4 Replies
View Related
Nov 15, 2005
I have a PC with 512 mem. XP operating system, P4. I added a new 160 gb. hard drive now called C and it made my old small hard drive F, a unused backup.I used Acronis true image to transfer all info to new C drive. I also have Norton Go Back loaded on my PC.
I noticed that my XP and Norton goback programs are monitering my old F: NOT MY new C: How do I get ''XP restore'' to moniter my new Cdrive not my oldF drive? Same question for Norton Goback. I do not add any info to my F drive on a regular basis. I want to have the safety of a relatively recent restore point for my new 160 gb C drive
View 4 Replies
View Related
Sep 22, 2010
I am try to two partition drive C and drive D in my computer but only one c or d instoling. i have 4000mb hardrive,please tell me how can i instol partition in my window xp professional.
View 1 Replies
View Related
Mar 8, 2006
I have a dual boot system (2 hard drives) booting Suse and XP and boot up through Suse's built in boot manager which gives me the option of booting to Windows or Linux. But since I barely ever use Linux I want to delete it off the 2nd drive so I can use it for a storage drive, so I'm wondering how to replace the Windows Master Boot Record so I can just boot into my XP drive. I'm scared that once I delete/reformat the contents of the 2nd hard drive (I'll probably use Partition Magic to do this through my XP drive) that I won't be able to boot XP up anymore. So before I do anything I want to just be able to boot into XP and bypass the linux drive before I delete it to make sure everything is ok.
View 2 Replies
View Related
Nov 5, 2007
I have a HP ze5568cl laptop (Windows XP SP2). For a few years we've had trouble with the power connector. We've just wiggled the power cable to keep it connected and lived with the problem. It also gets very hot and the fan runs constantly. Yesterday when I powered it on there was no power, absolutely nothing. My husband has some electronic knowledge so we took the laptop apart and he soldered the loose part of the power connector. While he was doing that I cleaned the fan (couldn't believe how much dust was in there.When we plugged in the power cable the orange light came on so we were excited. When we powered it on all the keyboard lights lit up so we thought we had fixed the problem but.that's all it did. It went no further except that the fan kicked on.There is a clicking noise coming from the cd drive about every second with the green light flashing. I suppose it is checking to see if there is a bootable cd in the cd drive. I have attempted to change the boot order by holding F1, then F2 but it still continues to try to read the cd drive. I can't get to the screen that will allow me to change the boot order.
I also put the OS disk in the cd drive, hoping that it would start with the disk but it just clicks. Hubby removed the cover of the cd drive and I could see that the cd is spinning.There were no problems with this laptop prior to the power problem. It was really working very well especially considering the age of it.
The information in my sig is not for the computer with the problem. It's actually for an old computer which my son now has at college.
View 11 Replies
View Related
Jan 22, 2006
I bought a computer for my wife and kids. Well months go by and my wife tries to install something and notices that the MAIN drive is H: not C:
I figured that it was weird but no big deal. Well I purchased a printer for her and while trying to install the software it was giving me a "Windows - No Disk in Drive" error.
I did some research and spoke to HP tech support and they suggested that I search the web for a way to change the drive letters from H: (current hard drive) to C: (supposed to be default drive)
View 14 Replies
View Related
Aug 30, 2008
I had a drive that was beginnning to squeal and i figured I could disable my drives one at a time to see which one was squealing. Of course, disabling the drives through the control panel doesn't actually keep them from spinning, so the whole thing was an exercise in boneheaded stupidity. Anyway, as soon as I disabled the c: drive the screen went blank (of course), and now when i try to reboot it complains about a non-system drive and asks me to insert a system disk. did I mention that this is a home-built system and it doesn't have a floppy, so i can't boot off the floppy? I tried booting off the XP install CD, but it won't except that either (this seems odd to me).
View 1 Replies
View Related
May 25, 2004
I installed a Serial ATA hard drive. Booted from floppy,partitioned and formatted 120mb HD,with 2 partitions.
Connected my old IDE drive and booted from Norton Ghostdisc, cloned my old drive to the new one. Removed all drives and USB card readers except the new SATA drive. Windows will not fully boot, it halts at the blue Windows intro screen. Restarted Windows, and scandisk ran, but indicated drive letter "H" not "C", so I guess the windows installation is still looking in the original place for it's files, ie. the "C" drive, that's why it won't boot. You cannot change the "System" drive letter from "Computer Management" within XP, and I cannot get into Windows anyway. Is there a "work around" for this, other than a clean install? Even then, is it still going to be drive "H"? And that means another Windows activation. How many goes do you get for activation? I tried a windows repair installation, and reactivation (wasted). Windows then worked, sort of. Lots of things were missing and programs unuseable,as they were looking for their files on "C": so I went back to square 1, put my old drive back in for the moment
View 2 Replies
View Related
Nov 26, 2009
I have a dual boot system with both having windows xp.When I load into the 1st XP installation, the following is the list and assignment of the drives:
C : Local Disk (contains the 1st XP installation)
D : CD Drive
E : Local Disk (contains data and also few installed program folders)
F : Local Disk (contains the 2nd XP installation)
Initially when I noticed this drive arrangement after setting up the dual boot, I just left it as is, not knowing what to do.But nowadays I am having a lot of problems as the installed programs are not accessible because their target location keeps changing, everytime I keep switching between the two operating systems.How can I solve this problem?Can I do the follwing : Load into the 1st XP installation, and then change the drive letters (of the last three drives) such that they are matching the drive assignment as seen when loading into the 2nd XP installation.Here in a way I have kept the same drive name for both installations.But Will this work?I also have some of the program folders for the 1st xp installation stored in E drive, and after changing it to D drive, will all the links be properly converted upon restart?
View 12 Replies
View Related
Apr 3, 2007
I have successfully cloned my primary c partition of a dual boot system with XP Pro on the 1st primary partition c: and XP Pro on the 2nd primary partition as d: I can boot into my XP on the c: drive with no problem, but when I attempt to boot into my XP on the D drive it hangs on the blue screen right before booting into the user profiles. And believe it or not it continuously loops making the windows startup sound and the shutdown sound. It does the same in safe mode. I will try to explain the process on what I did so it can help you experts figure out this dilemma that I'm having. My old drive an IDE 100GB IBM primary drive was partitioned into 3 parts:
c: 30GB FAT32 primary
d: 30GB FAT32 "
e: 30gb FAT32 "
All ran great in XP's on c: ,D: and :e except that i was running out of room in all the partitions and the drive is getting very old , I think (5yrs). I used XXClone Pro v.0.58.0 to clone my old c: and d: partitions to a WD IDE 160GB. I tried many other cloning proggys like Acronis True Image, Drive Clone, Paragon Drive Copy, Drive Image 2002, HDClone 3.1 Pro but they all either changed my new drive NTFS file system to FAT32 or made exact same size copies. I formatted and partitioned my new drive as follows:..............
View 2 Replies
View Related
Mar 31, 2010
I had voltage fluctuations last night due a snowstorm and the voltage dropped crashing my PC.It now won't boot and gives the error that a file is corrupted.Windows/system32/config..The PC runs an OEM XP home edition on a SATA drive, the PC also has an IDE drive (D) but the OSes are on the C drive.Inside the XP installation I have Linux Mint installed.When I boot I get the 2 options I always used to , XP (default) and Linux Mint.XP won't boot when selected and gives the error above.The Linux Mint, also on C and in fact installed as a program within XP, will boot, hence I believe the SATA drive to be undamaged.I can see the C drive and all the XP files from the Linux installation.I've tried using the original full CD and the recovery console but when the recovery console opens all it can see is the IDE drive which it labels D (and of course doesn't contain the original XP install.I can't remember how I got XP on the SATA drive in the first place, I don't appear to have any Hard drive drivers in the case I keep all software CDs in and I'm a bit flummoxed. I can only imagine I just fitted it and loaded the XP install disc but that's at odds with what seems to be happening now.Spent a large part of today Googling but can't find anything that will fix this. so far.I don't want to have to wipe and re-install everything unless there's no option, it's a fast way to kill a couple of days over the holidays.
View 8 Replies
View Related
