Setup Is Starting Every Time

Jun 21, 2005

I have a slight problem. I just recently replaced both my power supply and my hard drive, and when I try to install Windows, a blue screen pops up which runs through everything it's doing. No problem, right? Wrong.What's happening is: it says "Setup is starting Windows", and that screen does not disappear. It stays that way and never goes away.

View 1 Replies


ADVERTISEMENT

Hangs Every Time At Setup Is Starting

May 16, 2010

I'm trying to do a clean install on a laptop and every time I try to install Windows XP Pro, it hangs at the screen that says "Setup is starting Windows" I've also tried installing Windows 2000.

View 8 Replies View Related

Pc Hangs At Setup Is Starting

Mar 17, 2007

When I attempt to install XP it is hanging up at "windows is starting windows". It does it with either my XP or 2000 program.

View 1 Replies View Related

Setup Is Starting Installation Hangs

Apr 30, 2006

A new 250 gig seagate SATA 7200.8 hard drive and a win xp home upgrade edition. enabled SATA in BIOS, connected SATA cable to SATA1 on mobo, BIOS didn't recognize the drive, connected to SATA2 and BIOS did recognize drive so I tried to partition and format using Seagate's DiscWizard from floppy. Things seemed to go fine until I got a message that format wasn't completed because of some error.I went ahead and tried to install from xp cd, loaded SATA drivers from floppy, cd started loading but then hangs up at "setup is starting windows"I've never used SATA before.

View 7 Replies View Related

Pro Won't Get Past Setup Is Starting Windows

Jun 8, 2008

I can't get XP Pro to get past "Setup is starting Windows" ,to allow me to format.Loads all drivers up to that point,then the error in above post.Pressing F6 or F10 to install 3rd party(XFX MB drivers) has no effect,and Alt-F2 ultimately gives error also.S prompt is no joy also.Tried F8 for Safe Boot and no joy.Cleared CMOS several times.All drives are there in CMOS. All RAM (4 Gigs) is detected I raised Memory voltage to 1.9 volts standard for my ram),and raised FSB to 1600 Mhz from 1333 (standard also).Put timings to standard 7-7-7-24T Tried Memory linked/unlinked/Auto/1T/2T I Tried only 1 SATA drive,and 1 Gig of RAM with 1 DVD RW /2 drives and 2 Gig of RAM,I Enabled standard RAID for each and every drive and ultimately disabled them cause I want the XFX 790i ultra motherboard RAID Drivers.

View 6 Replies View Related

Freezes At Setup Is Starting Windows

Jun 10, 2008

When i put in teh Win xp disc its starts loading teh file etc.. and then when done after i press enter and "Setup is starting windows" its freezes andi get liek A black dot and a few like patterns on the screen or soemtimes teh screen just goes mad liek with different colourd patterns but ontop of the blue "Setup is starting windows" screen ive checked teh disc and made a copy both work fine checked teh CD rom works fine put a diffremnt cd rom drive in and made no difference cant check ram because my computer doesnt take DDR2. ive put diffrent IDE harddives in with and without a SATA convoertor and the same thing happens with the "Setup is starting windows" also when i start the computer up before i boot from cd or anything after all that without booting from CD i get a BSOD code 0x07B.

View 8 Replies View Related

Pro Install Hangs At Setup Is Starting

Aug 29, 2008

I am trying to install XP Pro on a machine with an AMD K6 clocked at 266mhz and 160mb of RAM. This is a laptop currently running Windows 98 SE. 98 works fine for me but I hate installing drivers. The laptop is an Compaq Presario 1235. I just want the laptop running XP, it doesn't have to be lightning fast. In setup, it hangs at Setup is Starting Windows. It does the same when installing Win2k.

View 4 Replies View Related

Windows Is Starting ' Wait Time

Dec 8, 2005

Im running windows XP Pro. upon starting the computer, when it gets to 'Windows is starting' screen, I'm made to wait at least some 3 minutes before I get to the Logon screen.

View 2 Replies View Related

Starting My PC With Home Takes Too Much Time

Jun 25, 2005

I am having problems starting my PC. Each time I boot up, the PC is very slow and it can take up to 10 minutes to see desktop icons on the screen. At first, it displays the Windows Welcome page, and this is displayed for about 3 minutes. Eventually, the desktop is displayed with the background picture,
the cursor is also there, but there are no shortcuts/icons are on the screen.

View 5 Replies View Related

Starting Up Scrren With Blue Bar Stays For Some Time

Nov 26, 2006

When i start up my computer the Windows XP screen (with the blue bar moving along the bottom) sometimes stays on for 1-2 minutes.

View 4 Replies View Related

Faster Startup Of XP: Long Time To Become Useable After Starting Up?

Apr 2, 2003

If your computer takes a long time to become useable after starting up or logging on, or you want a clean boot of Winodws XP try this,Click Start > Run > Type "msconfig"  > On the Startup tab click Disable All and on the Services tab check the Hide All Microsoft Service box and then click Disable All. Click Restart and Windows XP will restart with only the system services and applications running resulting in a vey fast logon / startup.

View 9 Replies View Related

Installing Process Stops At "Setup Is Starting Windows"

Jul 2, 2008

I have an old system I am installing a new hard drive in and trying to install Windows XP Pro on it. It's the only hard drive in the system, a Western Digital 500GB SATA. The MB is a Intel D102GGC2 with a Intel Pen D processor. Windows has run just find on this system. Replaced the hard drive because could not boot the installed windows. That hard drive is no longer installed in the system.

I insert the Windows CD and the install process goes fine till it tries to start windows setup. It stalls at "Setup is starting windows"

View 14 Replies View Related

Computer Will Not Install / Hangs On "setup Is Starting Windows"

Dec 29, 2005

I am trying to install xp on this good friend of mine's machine that took a dive last week. We replaced the motherboard, cpu, and memory. And afterwords for about 3 days, it seemed to function ok. Then it just quit booting. I told him we would need to reinstall windows. I was kind of shocked we did not have to in the first place. Anyways, So now I am trying to reinstall windows:I can get it to boot from the windows cd, it goes through the standard list of drivers, and at the end says, "setup is starting windows"... Then it just hangs there indefinately. Typically after this, you get to the screen that asks you if you want to install windows, then you hit f8 to agree to there stuff, then you get to partition ect. I mention these things so you will know what part I am talking about.

View 5 Replies View Related

HP ZV 6000 Freezes Hangs At "Setup Is Starting Windows"

Oct 5, 2009

Im installing Win XP Pro (SP2) on a HP Pavilion zv6000 laptop. Everything runs fine until I start installing windows xp. The cd boots and the "Setup is loading files" goes through but then stalls at "Setup is starting windows". Waited for 2 hours just in case and still the same results.From what I can gather this points to a hardware problem. I have tried different ram modules and removed the battery but all to no avail.Could this be a processor or motherboard problem? I did everything the person above me did and then I took the hard drive out, reformatted it and tried installing XP SP2, Windows Home and the recovery cd supplied by HP. Every time it is gets to "Setup is Starting Windows" it freezes. I know the hard drive is working since I tested it in another computer. The reason I needed to reload XP is the notebook would load and get to the Windows XP loading screen and then freeze.It wouldn't boot in safe mode either.

View 6 Replies View Related

Install Hangs On "setup Is Starting Windows"

Mar 28, 2007

I have an Intel 945GTP motherboard running XP Pro on a SATA HDD that, until last week, worked just fine. Then, it decided not to boot up one morning, in either regular or safe mode.It won't boot from the CDROM drive either. It does boot from floppy.I've replaced RAM, taken out all non-essential hardware, replaced HDD cables.HDD can be recognised in another system.Mouse and KB are not usb.I removed the HDD partition, intending to reload XP, but the load hangs on "setup is starting windows" and never goes anywhere - i left it overnight, just to be sure.I repartitioned and reformatted using a 98 disk, just for kicks, to see if it'd work. Yep, boots to c:> HDD manufacturer's diagnostic reports no errors.I have put in another, new SATA HDD, as well as a new ide hdd.

View 1 Replies View Related

Removing OS's From Boot Loader: Have Windows XP And A Windows XP Setup Same Time?

Apr 19, 2006

I went to try to install windows xp onto a computer that already had windows on it. I did not boot from the cd. To do it without using the cd it has to copy the installation files to the computer and then run them. When setup does this it creates a new choice of an operating system to boot from called "Windows XP Setup." So now I have a Windows XP and a Windows XP setup. I've been in msconfig and looked at boot.ini but that didn't help

View 8 Replies View Related

MS Word Starting When Starting Computer

Jul 10, 2005

I have Windows XP and MS Office XP (2003) loaded on my PC. Whenever I boot up the PC, 3 sessions of MS Word open - 2 sessions have a new (blank) document open, and the 3rd session just shows Word as being open (no new document).I went to Documents and Settings | Application Data | Microsoft | Word | Startup to see if there was anything in the folder prompting Word to open the 3 sessions. The folder was empty. I then clicked Start | Run | msconfig | Enter to see if Winword.exe is in the Startup folder. I thought I might see it in there 3 times – one for each of the Word sessions that are opening whenever I boot up the PC. Strangely enough, Winword.exe wasn’t in the Startup folder at all – not even once.

View 5 Replies View Related

Users Try To Install Fax Client / Setup Hangs Asking For Fx Setup Files

Aug 20, 2005

I've setup Windows 2003 fax services on a W2K3 server and shared the device. I've tested faxing from Word on my PC and it works fine.However, when other users try to install the fax client, the setup hangs asking for the fx* setup files. I've tried different XPSP2 CDs, copying the files to a local directory, making sure that the users have local admin rights (and even domain admin rights) but to no avail. The files are already in the system32 directory so in theory the setup doesn't even need to copy them. Even if I delete them, it doesn't work.Our corporate SMS team reckons that there isn't any policy which could
cause the problem.

View 1 Replies View Related

Pro Upgrade Fake Setup Call Himself Instead Original "setup.exe

Dec 4, 2006

I started an upgrade for xp pro part way through the install I got a message "WatchDriverSigningPolicy.exe" no found I pressed enter then got another message "fake setup call himself instead original "setup.exe" ; setup abort!" now each time I reboot it starts to load xp then gives me the same message then press enter it then reboots.

View 3 Replies View Related

Corrupt Setup / Trying To Remove Setup By Logging On From Another Disk

Feb 24, 2008

I mistakenly launched XP Setup and want to know how to stop it from progressing further. I have another XP installed on another virtual disk. Rebooting from there allowed me delete the Setup files. Or so I thought ! The main XP installation however continues to try to launch Setup. Just about whatever I do, it ends in tears. My question is how do I stop XP on this disk from thinking it has to launch Setup? I dont want to reinstall XP, as that will involve a huge amount of work to recreate my environment.

View 6 Replies View Related

2000 Setup Won't Complete - Setup Stops

Aug 4, 2007

I was told to reinstall windows 2000 aon a C800 I was given. I stopped with an erroro reading line 3221166496 hivedef.inf corrupted. Setup cannot continue.

View 3 Replies View Related

Starting Up It Gets Hung Up At "Windows Starting Up"

Mar 25, 2007

For about 2 months my computer (Sony VAIO desktop, Pentium IV 1.39 mHz, 512mb RAM, Windows XP Pro, SP2) has been acting strange. I have checked the system for viruses and spyware with AVG and Symmantec and others- with no luck. I also did a Windows repair; it only got worse. I also used reg scrub.First, when starting up it gets hung up at "Windows starting up..." taking about 3 minutes to finally get to the user selection page. Once I login, it takes another 2minutes to fully open up. At that point, my mouse has a constant flicker and takes forever to open up IE (6.0). If I leave the computer for awhile, when I come back and move my mouse to wake it up- it has some new problems: I cannot type in numbers (num lock has no effect), when I type letters, they are in all caps (caps lock off), and when I go to my desktop to select a program to start, it highlights all of the icons and says basically "do you really want to start 38 programs at once".

View 11 Replies View Related

Error: Setup Can Not Find Setup.exe

Oct 29, 2008

i am trying to install windows office 2007 but after a minute from start of installation ,it popup dialog box saying setup can not find setup.exe file and say browse valid installation source and click ok.
I don't know whats happening.I have just formated my C drive and installed fresh copy of windows xp.
here is image of error message.
what should i do?


http://img101.imageshack.us/my.php?i...9005582dv8.jpg

View 2 Replies View Related

Computer Date / Time And Year Change Each Time Boot Up

Oct 11, 2007

Each time I turn on my computer and as it is boots up it will delay for a time with a line that reads something like Automatic IDE Configuration and then a message that my date and time are incorrect. The date goes back to Nov. 2003. Once I correct the date, time and year things seem to perform ok.

View 4 Replies View Related

Computer Facing Slow Boot Up Time / Speeding Up Time?

Jan 15, 2009

How do I speed up the boot up time? It seems like it takes forever for my pc to boot up. Plus how do I find out what programs are loading at start-up? I'm currently running winxp and connected by cable to the internet

View 3 Replies View Related

UPDATE: Time Zone/Daylight Savings Time?

Nov 27, 2006

Since Windows has been released several time zone changes have occurred, and beginning this coming year the Daylight Saving Time period will change in the US. Specifically, DST will start three weeks earlier (2:00 A.M. on the second Sunday in March) and will end one week later (2:00 A.M. on the first Sunday in November). Thus, Microsoft is releasing an update to address changes that have or will take place in several countries. The update will be delivered automatically to Windows XP SP2 users starting December 12th (or can be downloaded now by clicking here) and will be included in Windows Vista.

View 23 Replies View Related

Winxp Computer Running Slow (from Time To Time)

Aug 28, 2006

i dont know where the reason could be, since i didn`t install any new programs or had virus problems. It just becomes slow, then I restart and sometimes it helps and sometimes doesn't.

View 4 Replies View Related

Time / Date Clock Looses Time After Shut Down

Sep 3, 2007

I have a 4 year old computer that runs perfectly, except when I turn it off at night and then back on the next day, I loose a few hours on the time date at bottom of screen. I ajust each time I use it but the same thing happens each time I turn it off. Could it be the clock battery or? My operating system is Windows XP Home

View 3 Replies View Related

Must Run Setup / Setup Won't Start

Apr 18, 2008

I dropped my laptop the other day. It kept working at first, but crashed a couple of hours later. Now, when I boot-up, I get the following error message:"Windows could not start because the following file is missing or corrupt: System32/Drivers/Ntfs.sys. You can attempt to repari this file by starting Windows Setup using the original Setup CD-ROM. Select 'r' at the first screen to start repair."I've inserted the setup CD (in an external CD-Rom drive, since my laptop doesn't have its own drive). But for some reason, setup won't start, and I keep coming back to the above error message. How do I start setup?

View 12 Replies View Related

System Shut Down Time To Time - Crashes

Feb 12, 2006

i do scans quite a bit and delete alot of things everytime. there is the msn spyware thing that keeps coming back after i delete that, as well as many other things i dont even know about. some of my devices just shut them selves down from time to time (mouse, scanner/printer, and otherthings i cant remember but the key board is fine) and after a few seconds turn back on. and the whole thing just crashes sometimes. i did that scan thing but im not sure if i did it right.

Logfile of HijackThis v1.99.1
Scan saved at 10:57:17 AM, on 13/02/2006
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP2 (6.00.2900.2180)

Running processes:
C:WINDOWSSystem32smss.exe
C:WINDOWSsystem32winlogon.exe
C:WINDOWSsystem32services.exe
C:WINDOWSsystem32lsass.exe
C:WINDOWSsystem32svchost.exe.....

View 10 Replies View Related

Mouse Freezes Time To Time - Ran Adaware6,

Oct 3, 2005

My mouse/pointer is STILL freezing after about 5 minutes of being logged on. I am using the touchpad mouse that is on my laptop. I have ran an updated version of Adaware6, Spybot, CWShredder & AVG Anti-Virus. I also have Spyware Blaster Protection enabled. I don't know what else to do but ask you guys if you see anything funny in my hijack log... Is it normal to have 4 entries stating info about my startup page? My start up page should be Ada County Sheriff, not Toshiba or Ebay

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved