compaq computer has bit the dust and I'm building her a new one. Her original 20GB harddrive won't boot up in the new system....it gets to where the XP colored window flashes, goes to a blue screen of death screen, but that blinks out so quickly that I can't read it or pause it, and the computer reboots itself. It won't boot into safemode either. thought the harddrive was dead since I could hear it click at that point
View 6 RepliesRecently took some hits on my Compaq Presario 7478 system. Got two or three nasties via the 'Net. After McAfee's virus scan and removal, began experiencing weird happenings, such as system closing down and restarting. Then just not starting. Tried a few remedies [probably inadvisedly], and finally the system seemed to hang on my restore at the same place repeatedly.Ultimately the system could no longer establish my OS. Restore failed.
Bottom line: Could not invoke computer restore. Could do nothing with this computer.Q... Being compaq is the BIOS set to a certain condition that would prevent my reformatting the hard drive and restablishing an OS? Is this an option I can override? If I were to piggy-back the existing hard drive onto an operating hard-drive and reformat would that solve this problem and permit me to then create or repair the hard drive subsequently to get my compaq back?
When I turn on my computer, it starts up like it's supposed to. Then, when it comes to the Windows XP loading page (you know, the one with the bar scrolling underneath it), it suddenly goes to a Blue Screen of Death for a straight millisecond, then reboots again. Then my computer gives me 5 options. I could load Windows at the previous settings that worked, load Windows normally, and there were three other options that involved loading Windows in safe mode. I've tried all five. All five result in the computer rebooting itself again. There was a timer below for 20 seconds for me to choose an option, so I doubt that it's a worm causing this problem.My antivirus is up-to-date and I do regular scans. I have a firewall.
It couldn't have been a power surge, because I have a power strip on the computer, and it says that it's protected. And, before all of this was happening (a few minutes before), my computer was acting normally. There wasn't anything funky going on, so I doubt that my hard drive was dead.
I want to wipe the harddrive of my HP Pavilion desktop and start from scratch. However, I have moved since I purchased it many years ago and I don't have any of the original disks.Is there any way to access a function in the harddrive to wipe what's there and just re-install what it came with at purchase? And will it be able to connect to the internet to get drivers, etc.? Sorry if this is a question that has been asked before... I am semi-literate when it comes to computers but I have never done a complete reinstall without the original disks that came with the system.
View 6 Replies View RelatedI have a sony vaio pcv-rx550 desktop that had a corrupt hard drive.It would not let me do a system recovery or system restore, so I wiped the hard drive with dariks boot and nuke,and ordered a new set of restore disks for my specific brand and model, but when i put the first disk in-it says ERROR: this recovery cd is not for your computer.I checked the dir. using a win98 setup disk and there is a sony folder and a image folder but I do not know the correct command to get them to load that way. any help would be appreciated.Can I use a regular win xp home disk to get it up and running and then use the disks to load the remaing software that came with it off of the restore disks?It had win xp home on it to begin with.
View 10 Replies View Relatedmy operating system is corrupt and i think my restore disks are bad too. how do i tell if they are and what can i do about it?
View 9 Replies View RelatedIm intrested in purchasing a product to clone hard disks in Windows but I have a question before hand If I clone a hard disk into some DVD´s and the I want to restore that image into another hard disk, a new, different size/brand hard disk. Is that possible? Is there a "correct" way to do it? Someone reccomendme either Norton Ghost or Acronis True Image, but Im not sure if itll help me. I hope your answers help me to decide weather to buy the software.
View 9 Replies View RelatedI have followed the wizard for system restore but having set the date and pressed next nothing appears to happen. How long should it take? I have tried this in safe mode as well
View 1 Replies View RelatedCompaq Presario 5000. Hard Drive failed, replaced hard drive and now Win XP Quick Restore Cd's that came with this PC won't load on new Hard Drive. Instead, I just get a red screen with ERROR and says to contact Compaq for support. I'm assuming something is "missing" that allows the Quick Restore to be "ok" with loading. I've formatted the Hard Drive.
View 5 Replies View Relatedi need to buy a compaq quickrestore cd. ive been looking online and they seem pretty hard to find. i found one website that might work but im not sure(restoredisks.com). also, i found somewhere that there was some type of settlement with compaq and that i might be able to get a quick restore cd for free through https://www.orderz.com/qrcons/page1.asp i have my serial number on the side of my computer so everything would be legit. if worst comes to worst i might just call up compaq tech support and try and buy one from them but im not sure how much that would cost.
View 10 Replies View Relatedmy desk top is using xp and i cant access it i have tried all sorts of things boot disks, recovery disks but still no joy, tell me to format then i can start again,
View 8 Replies View Relatedwhen a memory failure corrupted the OS. Compaq runs its setup from a special partition on the HD and Ive reloaded all of that from floppies. Setup says I have a 26.2GB HD but it is 60GB, otherwise all tests pass. In setup under storage the help file says I can select the boot sequence but I cant seem to find anyway to do this?? Id like to boot from the Win 2000 CD, I did make a boot floppy set from the 2000 CD but it dies on disk2 with a "isapnp.sys corrupt". Downloaded another makeboot.exe diskette set and get the same message. The original OS starts to load off the HD but stops with an error message and only allows a reboot. Can I move this HD to a slave on an XP system and load 2000 that way and then move back and configure the different hardware? Or just boot from the CD on my other PC and install
View 4 Replies View RelatedI have a Compaq S4120WM with Windows XP Home. I would like to be able to copy the restore information from the D Partition to a DVD so I can restore should I lose the drive. I can simply burn the info to the disk but how would I start the restore process
View 3 Replies View RelatedHello,can i burn Free compaq restore disk
View 1 Replies View RelatedI just did a restore on a compaq laptop that is about 5 years old. It was having problems connecting to internet so I started the restore a few years ago. When I started the restore it was just shutting off on me. I gave up and bought a new computer. Well just a few days ago a good friend of mine passed away, and his family wants pictures that I had on this computer. Went to start it up and see if it would turn on. It did and continued with the restore, It finished the restore, but now there is none of my data left. I would love to get these pictures back
View 3 Replies View Relatedi am trying to restore to factorey set up a compaq presario 7oo to be donated to someone. i found the recovery cd and the quick restore cd 1/2/3 however none of these is the one I need. Am I missing a cd
View 9 Replies View RelatedI decided to install an old hard drive from one of my computers that is no longer used into my aging desktop. I've always dual booted with Linux, and decided that with the extra space, I was going to put Linux into the "new" drive, and reinstall Windows on the old primary drive. Both are IDE, and the following problem occurs whether just the Windows drive is plugged in, or if both disk are hooked up: I have a Compaq SR1620NX. I've only added extra RAM, a TV Tuner, and the extra hard drive When I put in the Compaq restore CD's, you first boot from the CD's, in order to copy the files first (which are the first 50% of the install), then the computer reboots into XP, and continues the installation process (Mostly Drivers, Crapware, and the license key). I've done this process once or twice before, and it worked flawlessly, this time it keeps freezing.
Once the computer boots into XP, I'm prompted to insert the final recovery disk. A few files are copied over, and the computer reboots. Once the computer reboots, the same screen pops up, and continues the installation (as it's suppose to). After a minute or two after the reboot, the computer locks up completely. I've waited quite awhile, yet nothing happens. Although it's against what the screen says, I hold the power button in, and let the computer reboot. Again, the installation screen pops up, but nothing happens
I'm a little lacking in memory, so I think this one has hit the bit bucket on me. I use to do alot of Compaq service and know there is a way to force the quick restore to go in on a new hard drive with a keystroke combination while its starting up, but for the life of me can't remember the what the keystroke combination is.
View 2 Replies View RelatedI have a compaq Presario S5200nx that i do not have the restore disk for, its out of warranty and they dont make the restore discs anymore. I do have a win xp home disc, which I installed but cant enter the product key for the licenced copy of windows xp home that i own. can i download a restore disc for this pc, or a way to get past the prod key screen
View 5 Replies View RelatedThis is not good, I think. I did a system RECOVER on my Compaq and LOST EVERYTHING (WORD FILES, PHOTOS, ETC.). Is there a way to undo a system recover? I tried to do a system restore to an earlier point but there were none
View 11 Replies View RelatedCompaq Presario SR1265SCL Restore issue. When I try to take the PC into the F10 restore I get the error: STOP: c0000221 unknown Error system Reboot system dell.dll. Can anybody tell me if the restore partition is damaged
View 7 Replies View RelatedAfter starting my pc i noticed what 99% of data in my hard disk has vanished. it used to be only a 1GB free space there and now it shows 38,8 out of 39 GB. I tried system restore in normal and safe mode. .Thorough description of situation:
PC runs on Windows Xp SP2. It has 2 hard drives where the biggest one is paritioned into three drives: one for Windows installation, second was used for installation files of other programs (I kept Program Files folder there) and the alst one was dedicated for data storage. So the problem occured with the second drive. and as a result i do not have most of my programs running.
I have a compaq computer and have a problem with the restore cd from compaq. I needed to reformat the hard drive because of some crup files. When I put the restore cd in the computer is says the cd's are not for this compaq. I taked to compaq and gave them all the information they ask for and was told that I had the correct cd and it must be a bad cd set. They had me order a new set of cd's from there online store which I did with the part number they gave me after I double checked the number to see if they were correct and I got them in yesterday and still had the same problem. I talked to hp again last night and was told that the mother board most likely needed to be tatoo to match the cd's. I was told to take it to one of there repair stores to have this done. Never heard of a mother board changing it's self.
View 6 Replies View RelatedI know what to do but i am bit curious on the formatting bit. I have 2 hard drives, Harddrive "A" has all the window/program files as well as other programs like games and documents. Harddrive B is where i keep all my big files like videos and movies of course i want to format harddrive A but the thing is that harddrive is split in to 3 drives (C:, G:, F. I dont mind formating the c drive since it is all windows/program files but i dont really want to get rid of the G/F drive. I kno you can format the harddrive through the installation process of windows but i was wondering if it is possilbe to just to format the C: during that process or does it only format the whole harddrive
View 2 Replies View RelatedI reformatted my hard drive due to OS issues, I was running a trial version of Server 2003 along with XP Pro, and I had to get rid of Server 2003 because it was conflicting with XP Pro, and so the only way to do that was by reformatting both hard drives including XP Pro because Server 2003 was acting as the dominant OS, so I backed up all my ****, and reinstalled XP Pro, but now I get this hard drive problem that it says only 51 Gigs are remaining on a 250GB Hard drive, when the only thing installed on that hard drive is XP pro and maybe 15 applications, I tried using every program I can think of to find hidden files that equal a huge size but nothing shows up
View 2 Replies View RelatedMy computer operated windows XP sp2, and have 3 hard drives conntected
1. HD 0 is 160 GB divided into 2 partiotions, one 20 GB containing the system the other 140 Gb containes data directories and film directories2. HD 1 is 120 Gb connected through mobile rack and also contains data directories and film directories3. HD 2 is 200 Gb connected through mobile rack and contains only film directories.Untill thursday night everything was perfect, but when i I opened my computer friday morning i found the following1. HD 0 second partition all film directories completly disappeared and the free space is 40 Gb instead of the original 50 Gb
I got a trojan that attached to my browser. I managed to get rid of it by system restore.A few days later I noticed I only had 127 GB of my 300GB harddrive showing.I did manage to find the missing space though Disk Management. It was showing 170GB as unallocated space. I named it E: and formatted it.It now shows in My Computer as New Volume E: When I open E:I get 2 folders, Recycler and System volume Information. SVI will not open. It gives me an error, ESystem Volume Information is not accessable, access is denied.I am trying to find a way to either resize E: to 1GB or smaller and move that 169 GB back to C: or get rid of E: altogether and put all the missing space back on C:
View 14 Replies View Relatedabout two yrs ago my dad made a massive mistake of making two partitions on my laptop, and giving the C: only 2gigs of the partition, and the D: 28-29gigs. I wanted to format my computer completely anyways, and would like to know how i can format my computer and merge these two partitions. I have the formatting disks, but it never goes to a screen asking me about my partitions, it just formats everything on my C: (my default drive), but keeps everything on my D: intact (games, files, etc.).
View 8 Replies View RelatedRecently upgraded my laptop to windows XP from ME. I first replaced my 5 gig hard drive with a 20 gig hard drive. I added another 128 memory module for a total of 256. For an old machine it really hums now. Three minor problems are bugging me though. 1. I lost the sounds from my modem. The modem works fine except for no sound. I assume that the sound is from the unimodem half-duplex audio device that is located on the Lucent winmodem. I have checked everything. The system says that it is working correctly. I cannot even find the driver for this on microsoft . I thought if I could load a new driver it might work. No such thing. 2. System restore didn't work until I erased all the memory points and reloaded the program. Now if I open siystem restore and click on "settings" or "help" System restore shuts down. I assume it is corrupted and would like to reload it.
View 2 Replies View RelatedThe computer takes my password to sign in and I get a message "a problem with the hard drive has been detected consult with the troubleshooting section of your user manual.Hit enter to continue.Then I get the gateway picture and it says hit F4 to continue.It just freezes.
View 7 Replies View RelatedI have had an Acer Aspire 5670 for about 2 years. This morning, it was making a horrible noise (I left it on overnight and couldn't hear the noise until I went into my office). It sounded like a fan or spinning noise of some kind, but also might have been an audio file that was stuck repeating the first tenth of a second of the track. In any event, the monitor was dark and the PC was totally nonresponsive. I did a hard reboot and since then, the PC has not worked. The power button does turn it on and I can hear the HDD spinning and the DVD/CD drive looking for a disc (and it will accept/eject discs) but the screen never comes on and the PC doesn't seem to boot up. I don't ever hear the Windows welcome .wav file.
how should i fix the problem?