Network / Sharing :: Connecting To Other Machines On Local Network
Jan 26, 2014
I have two desktop PCs connected to my router, one named Mirabel running Win7 Pro, and one named Bessie running Win Server 2008 R2 (both 64-bit). These can see each other quite happily.
I just installed Windows 8.1 Pro 64-bit on my Dell Vostro 3750 lap top, which I named Rosie, but am having problems connecting to the other machines.
When I go to the Network node in Windows Explorer on Rosie, I can't see either of the other two machines, but if I type Bessie in the address bar, it shows me the two drives that are shared. However, if I try and explore either of these, I get the following error...
The laptop is part of a workgroup, imaginatively named "Workgroup" as are the other two machines...
I changed the properties of the TCP/IP v4 to match the ones on the other two machines (with a different IP address of course) but this didn't work.
The odd thing is that I can browse the shared drives on Mirabel without any problem. In case it's relevant, both desktop machines can browse Rosie without problems. Windows 8 has changed so much from Win7, and it's wasting a lot of time trying to get it set up.
I just bought my daughter a Lenovo running Windows 8 and when I try to connect to my Wi-Fi I am getting Limited connection only and can't figure it out.
This is a boot up timing issue, registry fix for network comming up. I am on a wired LAN which works ok. However, recently when booting I am getting the message cannot connect to network drives - these are mapped drives to NAS boxes.
However, when I access the drives the 'red X's' change to the network symbol and access is working. Its seems the computer wants to connect before the network is up. It is not a credential issue, but boot order. Is there anyway to make the network come up before the computer wants to map to it. Not a problem but a nag.
Wifi worked, walked away for 10 minutes, then found that it didn't. I would normally just reset the router, but I live in an apartment building and the router is in my landlords office.
When I did ipconfig /all, my ip started with 169, which I know isn't normal. But when I try to do a /release and /renew, I get the error "No operation can be performed on local area connection *14 while it has it's media disconnected." I am unable to attempt a wired connection, as the router is not accessible to me.
.I'm not sure if this is a router issue, or an issue with my laptop (less than a year old.) I am a grad student and I currently have to do most of my work via my iphone, which is getting very inconvenient.
How can i create local WIFI network without having internet access on my pc. This seems to work if I have access to internet but when i disconnect internet connection my PC ( virtual router ) cannot see anymore other devices..
All other devices that are connecting to my virtual hostednetwork are working without any problems expect my pc. What have i missed that my PC where virtual hostednetwork is running cannot see devices in "virtual" network without internet access?
Sometimes when I boot up my computer the wired network doesn't connect. I cannot connect to it unless I reboot my computer. Then iti works fine. The connection seems random and sometimes it works and other times it doesn't. If it does connect there is never a crash or error of it not working.
I have the asus P8Z77-V PRO
I disabled my wireless adapter to try but still same issues.
My friend got a new computer and is trying, unsuccessfully, to connect to a network printer that he says he has used in the past, in his one man office. He gets his internet access through a wireless router. But the printer is connected via Ethernet cable to a second router that does not have internet access, but does have two printers connected to it.
So his new computer is connected to two different networks, the wireless network, and the wired network. I'm not familiar with having your computer connected to two networks simultaneously.
So my question is, is there any problem doing it like this, and should the network printers show up when the computer does a search in Add Printer? Because it does not find anything right now, not sure if we need to be looking at the printers, the router, or the computer.
He is not able to connect the printers to the wireless router, they are in different rooms. And there are no other computers connected to either network right now.
I have an old computer that I've repurposed as a file server for all the other machines on my network, and one of the things I do with it is to put various program installer files on it, so I can install them to the other machines without having to download the same file over and over. However, when accessing these remote files from any machine except those still running XP, I get an extra warning box telling me that the file "is in a location outside your local network." It's not, but for some reason, these machines think it is. I've Googled various fragments of text from these warning boxes (each Windows version has slightly different wording for this warning; the screen shot I've attached is from the Win7 machine I happen to be on right now), but no matter which variant I search for, everything I find about getting rid of this warning is either geared toward similar warnings given by MS Access for remote databases, or for marking external Web sites as trusted.
How do I tell Windows that this local file server is in fact local and not in need of these repetitive and annoying warnings?
I have a local network at home with 1 router, 5-6 computers and a few gadgets connected through WiFi.
I have a problem with one of the computers with Windows 8.1, let's call it Computer A. When I boot it, it is connectable from the other computers using its local IP address. But after a few hours it usually disappears from the network, and I'm only able to connect to it using the router's external IP and port forwarding.
By "disappears from the network", I mean that it's still connected to the router and to the internet, but none of the other units on the network is able to connect to it in any way.
Computer A can always connect to the the other computers on the network and to the internet.
The problem is solved if I reboot Computer A, so at the moment I have a scheduled task to reboot it every night. Unfortunately, sometimes it disappears from the local network after only a few hours after boot.
Turning the firewall off on Computer A doesn't work.
Below is the result of ipconfig /all on Computer A:
Code: C:WINDOWSsystem32>ipconfig /allWindows IP Configuration Host Name . . . . . . . . . . . . : bjarte-media2 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : getinternet.noWireless LAN adapter Local Area Connection* 2: Media State . . . . . . . . . . . : Media disconnected
when extracting an archive to the same network location on which the archive itself resides, why is it that I'm having local bandwidth usage?
As you can see, there is simultaneous ~150Mbit/s upstream/downstream on my local ethernet adapter. WHY? As far as I am concerned there should be no meaningful traffic since it's actually a copy process on the local hard disk of my server.
I am trying to find a solution to transferring large files (100+GB) between myself and a client of mine at a different location through the internet. The easiest one I have found was through a Private Network through Logmein's Hamachi, as you can browse other connected computers' files through this network.
Of course, to show the shared drives by the host computer, you need to input a username and password through the UAC. Obviously, if I insert my own username and password, I can see the folders I've shared. However, how do I configure a username/password for my client? Are these users the same as local users? I would like to avoid having to make a local user for him on my own computer.
Just for reference, I have no control over my network I am connected to, so no FTP, no port forwarding etc.
I brought my laptop to work and wanted to connect to my work's network so I could access our shared networks. In the past I was able to log into my work's domain, nahrc, with my user name and password via the ctrl+alt+dlt method fromt he log on screen. I can plug in the ethernet cable into my laptop, and the nahrc network appears in the wired connections area, but I can't seem to connect/access our shared drives. Is it possible to log into my laptop like you could in windows 7 and access my account, or is this just not possible anymore.
I have a Netgear WN111 wireless adapter on my PC. Since installing Windows 8.1 it doesn't connect automatically to the router. The PC says there are no connections available, so I can't even click on the router to try to connect. If I pull the adapter out and push it back into the USB port it connects automatically. Also, when I switch the PC off, the LED on the adapter continues to flash, so I have to pull it out and plug it in again to stop that. I've tried troubleshooting, compatibility check, reinstalling the driver and uninstalling the driver and getting Windows to install one itself.
For some reason I can connect fine when I plug in my wireless receiver port into it, But 30 seconds after I plug it in, the bars disappear And a red X appears over it, if you click on it it'll say no networks found.... The only way to fix it is to plug it in and after 30 seconds it happens again...I'm only getting this on my computer, And it's gotten really bad recently, I've tried replacing the reciever, But that fixed it for maybe an hour....
I have a neighbor who has an OPEN network called @HOMED689 . For some reason my Windows 8 machines keep trying to connect to this SSID automatically.
I've never tried to connect to it. Once it's connected however, with limited connectivity, I don't have the ability to right click on it and say "Forget this network" or do anything to it such as when I connect to another wireless it says:
Show Estimated Data Usage Set as Metered Connect Forget this Network View Connection Properties
I bought Windows 8 when it was released, like most people I liked the performance upgrades and other stuff, but that was about it. Months later I installed Windows 7 again, but it just felt old and there were a few things I missed about Windows 8, anyway yesterday I decided to install Windows 8 again (8.1) but I'm having a problem since I did.
Whenever I connected an external hard drive via USB3.0, Wi-Fi would disconnect. I searched this over to see if other people were having the same issue, there were some guys but they were using a USB based Wi-Fi adapter, I'm using the one in the laptop.
DETAILS Asus U47A Wi-Fi adapter: Intel Centrino Wireless-N 2230 External Hard Drive: Seagate Expansion Portable Drive (500GB, USB3.0) OS: Windows 8.1 Pro, All updates (Problem happens with or without updates, with original (Asus) or Windows supplied drivers)
I was loosing the Wi-Fi connection and I didn't know why, it was very intermitent, it would work for 10 minutes and then not, I then downloaded new drivers, directly from Intel, Asus and then using the Windows Update, it didn't work in neither case.
I was watching youtube and noticed the signal was good, it was working fine, and realised that the Seagate HDD was disconnected, I had just isolated the problem.
I tried to replicate it and indeed it happened, whenever I connected the drive, signal would be lost. At first I thought it might be a hardware-based issue, but it was working fine with Windows 7, so I decided to play with it a little more. I found out that Wi-Fi connection wasn't being lost, but rather loosing power, Windows would only display the closest routers (two, out of five or six that are in range). So I enabled internet sharing in my cell phone, guess what? It worked fine, signal was strong.
I connected the Seagate drive to a USB2.0 port, no problem. Then connected a different HDD (USB2.0) to the USB3.0 port, no problem.
So the thing is that Wi-Fi loses power when the USB3.0 HDD is connected to the USB3.0 port.
recently my PC updated when I didn't want it to and now it installed the update 1 "patch" for 8.1 and now my internet driver is screwed up. I tried to remove it now but the network still won't connect. My network driver is the Killer network. I also tried to restore but apparently my PC never made an automatic save. Now what do I do?
I have a 60mb fibre broadband - on my old laptop (Win 8.1)with no external antenna, only what is built into the machine - I am getting over 62mb on several tests. My desktop - fourcore intel i5, 8mb ram on Windows 8 has no antenna either so I have an Alfa (AWUS036NH) with a 6db gain aerial attached, is struggling to reach 20mb. They are located side by side.
I have a Dell Inspiron 660s running Windows 8.1, and I just did a full boot of Ubuntu 13.10 onto a Dell Optiplex 330 that was previously running Windows XP. My goal is to connect to the internet by using the 660s as a bridge to the internet by connecting the two computers with an ethernet cable.
The level of difficulty: My internet requires you to log into it on a separate browser log in page similar to those in airports and other public Wi-Fi access points except that it requires a username and password to log in. My theory is that if I first log in to the internet on my Windows machine then I can connect to it by simply opening a connection from the Ubuntu OS to the Windows OS. Am I off track here or am I on the right track?
I have connected my ipod touch 4g to my new windows 8 laptop via bluetooth. It shows up in both the ipod and in the windows settings as being connected. However, once connected, i am unable to do anything with the connection.
There is no Windows tile showing the ipod, no obvious options in the ipod for how I can do anything with the connection, nothing. What am I supposed to be able to do once I have connected them via bluetooth? Is there a step I'm missing? I've read you can stream podcasts to the computer, for example, but there's supposed to be a windows tile showing the ipod which I'm definitely not getting either in the start menu or when I search.
At my last place of work I primarily used Debian; at my new workplace, I really need to use Windows 8 on my desktop; that in itself is not a problem. The problem I'm experiencing is that the native RDP client (remote desktop) will always use the server's local keymap - and I do not use a qwerty keyboard. My opinions on this aside, I appear to have two main options:
1) Find an alternative RDP client which uses the local keymap, as the Linux clients generally do.
2) Simply learn to use qwerty.
I've had to luck with option number one, so before I start the misery of number two, I thought I'd try a last-ditch attempt, and ask others.
I'm setting up for the first time a Homegroup (on Windows 8.1) between laptop and desktop. So far, Im impressed with the speed of transmission from one computer to the other. However, I noticed that I can only access the C: drive as well as the Library stuff such as Music, Pictures, Desktop, Downloads, etc folders. I would like to be able to access from my laptop the OTHER DRIVES on my desktop PC. What's the best way to do this?
I have a new Dell laptop with Windows 8.1 - I work from home & connect to the internet via my home wifi network. The problem I have been experiencing is that my laptop connects to the internet at boot up but then disconnects for several minutes & then re-connects again. This coincides with the Network & Sharing Centre showing a number of Local Area Connections (numbered 3,4,5,6 etc) being created under Unidentified Public Networks. I have tried disabling the LAC's but they re-enable whenever I re-boot & I have the same issues again. My networking knowledge is very limited so how to rectify this issue.
Have a question regarding "Local Account". I'm having problems connecting to the Win 8 laptop from Win 7 as it will not accept my sign in credentials. With that, am I to assume that this is because the credential aren't "Local", and thus this is what this is for???
It will not accept the "Microsoft" account I use to log into Win 8 laptop.
With that, if I choose to go with the "local account" can I easily switch back to the Microsoft one?
I upgraded my Windows 8 PC to Windows 8.1 yesterday and I am unable to reconnect it to my Homegroup (comprising of 2 Win 7 machines) or in fact get any communication between the Win 8.1 machine and the Win 7 machines. Prior to upgrading the Win 8.1 was part of the Homegroup. From the Win 8.1 machine: it initially detects the Homegroup as shown below,
it then asks me to choose file types to share and then asks for the Homegroup password which is when I hit problems as shown below:
In advanced sharing I have all 3 network types set to discoverable.
As part of the debugging process I discovered that the Win 8.1 was not time synced to the others, when I attempted to sync the time from the various time servers in the Windows drop down box I found the Win 8.1 encountered errors and would not sync. I was eventually able to sync it to time-b.nist.gov.
The other odd thing is that the keyboard does not work properly, specifically the characters above the numbers on the numeric keys are not correct, for example press shift 2 gives # instead of @. Have a suspicion these 2 things are somehow related.
Is there a way to setup network profiles or something so that when I bring my Surface Pro to work and connect to the wireless network there it will use the static ip address I have but when I disconnect and then connect to my home wifi it will go back to DHCP? On my MacBook Pro I can go into the network settings and change the location profile I have setup for networks but I don't see anything like this for Windows 8.
This morning I installed an optional update from Windows Update. It was Ralink Technology WLAN 802.11 wireless LAN card.
Since then, when I try to print to my wireless network printer, the network would disconnect then come back on after a while. The update shows up in Update History as successfully installed but not in the installed updates. System restore is of no support here. The network configuration page shows normal. The web does not appear to be affected. I made a new network connection for the printer but it did not work.
Is there a way to reverse this update or should I uninstall the 802.11 LAN card and let windows re-install anew.
