ASUS P8 Z77-V LK mobo has 1 each VGA, HDMI, DVI-D & Display
At first I was not confused thinking I could use VGA or DVI for my monitor and HDMI or VGA for my TV
Then I started reading about 'Display Port' and confusion set in.
1. -> Can I just use HDMI & DVI off the board at the same time to use 2 monitors ?
2. -> or Do I have to use an adapter and 'Display Port' for the 2nd monitor ?
I've been looking at some of the MATROX graphic cards for multi-monitor output -- up to 8 possible !!
Now any decent software to run these -- the standard software seems OK at running TWO monitors but I want to be able to run several more. You can run more but it gets a bit complicated managing this from within the standard windows system itself.
Five Best Tools for Managing Your Multi-Monitor Setup
I have a brand-new HDCP supporting monitor (native resolution 1920 x 1080,) on which I play the latest blu ray movies from the computers built-in blu ray drive, and a 9 year old flat screen non-HD plasma TV (on which I watch You Tube, BBC iPlayer and 4OD, streamed from the PC via a VGA cable,) both connected to my GT610 NVidia graphics card.
It seems I can only get them at the same resolution. My desktop does however have it's own on board graphics processor. Is it possible to run these two devices at different resolutions? (Since the ancient flat screen can only handle resolutions up to 1600 x 1200.)
I have just rebuilt my PC and decided to make the jump from Windows XP to Windows 8. The jump has not been smooth, but it looks like I have ironed out my biggest problem (incorrect installation due to not creating a system partition therefore Windows 8 = no DVD, no boot; rookie error).
Now I am stuck with an issue - windows detects my only screen as more than one. Sometimes it thinks I have two, more often it thinks I have 3 or 4. Installing the current nVidia drivers did not work.
What I have at the moment is 2 generic non-PnP monitors and 2 generic PnP monitors detected, according to device manager. nVidia control panel calls them Dell SX2210, VGA display, (i can't recall the 3rd one, I'm on my laptop now), and TV. Windows display setup calls two of the SX2210, and the other two are either generic non-PnP or PnP monitors. In nVidia control panel it looks as though I have a clone setup (2 screens enabled) with the Dell SX2210 and the VGA display. In windows display setup it looks as though I have a clone setup (2 screens enabled) with Dell SX2210 and generic monitor.
I have repeatedly unchecked the secondary monitors in both nVidia control panel and windows display setup, leaving me with what should be a single monitor arrangement and 3 disabled monitors. This works until I restart my computer, which then reverts back to what it was before. This is OK as a workaround most of the time, but sometimes when I boot up the computer it detects the wrong screen as the primary and I get a monitor which goes to power save mode. The solution to this is Win Key + P and change the display selection while blind, which works now I know how. Sometimes my screen will refresh (installing programs or drivers) and I get the same result. Detect displays also results in no signal to my monitor.
Currently using DVI from the graphics card to DVI on the monitor.
System specs:
CPU: Intel 3570K (stock clock)
MB: ASRock Extreme4 Z77
RAM: 4 x 4GB 2133 GSkill
VIDEO: Gigabyte GTX260 OC
MONITOR: Dell SX2210 @ 1920 x 1080
OS: Windows 8 64bit
*Yes I know the 260 is an older card, it has come from my old system for economics reasons (to be upgraded later), but it was working perfect on that machine.
I'm building a system for cryptocoin mining, and am having a little problem with getting Windows 8.1 (home, not pro) to run the 3rd card (GPU) My equipment is:
Gigabyte 990 FXA UD3 MOBO
AMD Vishera CPU
2x4 gig Corsair Ram
3x Sapphire r9 280x Video cards
1000w Corsair PSU
Scandisk SSD
All parts are brand new.
Here is the problem... everything boots just fine and runs with 2 of the GPU's installed. I have the latest AMD 13.12 drivers, and the AMD APP SKD installed. When I add the 3rd GPU though, windows will auto detect it as a Radeon 7900 with the caution sign, AND/OR a r9 200 series card, also with the caution sign, most times BOTH. Then it randomly freezes the system. A couple of times I got it to run long enough just by luck I guess, to install the 13.12 drivers on the 3rd GPU, but then in a few minuites the system would freeze again.
2 GPU's run just fine, the problem only shows up when the 3rd card is installed, and it happens on any of the 4 16x slots, or both 1x slots on the MOBO. It doesn't matter if the GPU's are directly on the MOBO, or on 1x16 risers. There are plenty of folks running this set up with up to 6 GPU's, so I know it can be done, but I must be missing something somewhere in the windows set up.
In a few weeks (I can't wait! ) I will replace my laptop with the Surface Pro.
Right now, though, I have my laptop connected to two monitors: One via VGA and other via DVI. I'm running Windows 8 Pro x64, so this all works great.
So the big question is whether it is possible to have multi-monitor support via the one-and-only DisplayPort that is on the Surface Pro? If so, what--if any--additional hardware would I need?
When I'm docked at home and using my Surface Pro as laptop, I really need to keep the functionality of using both external monitors (one is 31" and the other 29"). I would really hate to go back to only being able to use one.
I have 3 monitors, BenQ RL2450, two of them via DVI and one via HDMI.
Issue, HDMI connected monitor goes black every now and then. Not really a pattern in it. Sometimes it can flicker black once every 5 min, sometimes once every 30 minutes. Monitors are ok, checked with other computers, cables are OK, tested on different monitors and HDMI on TV.
I am suspecting drivers, so did a complete uninstall with graphic removal tool, then installed latest WHQL and beta drivers, still the same. Seen several users with the same issue, but no solution.
Graphic card keeps 40-50 Celsius while gaming, so that's not the issue.
Just can't remember back when I did not have this issue, hasn't been there forever.
All monitors on 60Hz, and with the same resolution.
I'm currently running Windows 8.1 Update with an NVidia 660TI with two DVI monitors at 1920x1200 and a 1080p TV from the HDMI output. I'm having trouble with the 1080p TV in that when I drag an application (Store or Win32) onto the screen, the top and bottom is truncated when I maximise it. For example, if I drag Windows Media Player over to the TV and maximise it, the play, forward and rewind buttons when visible are cut in half at the bottom of the screen.
View 1 Replies View RelatedAfter upgrading from Win7 (x64) to Windows 8.1 Professional N (x64) my system started to freeze randomly. It seems to be a driver related issue, since the freezes do not occur, when I disable the video card in the device manager. I recently upgraded to the new beta driver (v14.1) which made it even worse.
I contacted the ASUS-support already. They said the card is broken - which does sound strange to me, since it worked fine using WIN7.
Hardware specs are:
CPU: Intel Core i5-4570
MB: ASRock Fatal1ty H87 Performance
Video: Asus HD7790-DC2OC-2GD5
Memory: 2x 4GB DDR3-1600 Kingston ValueRAM
PSU: Enermax Liberty - 500W (ELT500AWT)
I used to connect my Asus X72JR on my Flatscreen TV at 1080p, it always had a crispy sharp image.
After replacing my harddrive and reinstalling Windows 7 (64x) the image wasn't displayed in full size of my TV anymore but smaller (black edges around image) When i set my TV to full screensize everything gets blurry (it just spreads the image)
I updated to the latest graphic driver and looked at the screens resolution which was still set at 1920x1080 (recommended), everything was correct but the screen is either blurry or displayed smaller than the tv screen.
My Asus has a Radeon Mobility HD5470 driver
I have a second laptop, when I connect this to the TV is has a sharp image again even though the settings are exactly the same.
I'm trying to use an external Samsung TV/monitor (model LN-T2642H) through HDMI. The native resolution of the monitor/TV is 1360X768, which is also the native resolution of ASUS T100.
If I try to use the monitor/TV as the only display, the device selected is Generic PnP Monitor and the native resolution of 1360X768 is not available for selection. Intel HD Graphics Control Panel only shows 1280X720 (selected) and 1920X1080 (too high for my monitor).
Is there a way to set up the 1360X768 resolution with the existing driver (up to date)? Is there another driver that I can download and that will allow this resolution? Can I use a different version of the Generic PnP Monitor that allows 1360X768 resolution?
With the only resolution available i.e., 1280X720 the quality is bad.
I have an ASUS s550C running windows 8 and my HDMI to my 32" RCA flatscreen doesn't work anymore. The cable works fine with the xbox, correct tv modes, but now as soon as I plug in the HDMI to the Ultrabook the Ultrabooks screen goes black and the tv screen says unsupported. I have tried extended, 2nd screen only, and all screen settings, 720/1080I etc.
View 4 Replies View RelatedI recently broke the screen to my asus n56vz. I ended up removing the whole top panel and removing the inverter cord.
I plugged in a external monitor and it worked fine at first. When i restarted i noticed that it starting running hotter and displayed a second option on a 768p monitor. My 1080 aoc was made the main display seen though its not the first monitor its second.
I tried to delete or disable the second monitor but i could not. What should i do?
I used to have 33c temps idle and not its 50c. It used to display only the external monitor. Now it displays 2 and the 2 is my main.
I dont have any recovery or 8.1 disks... I tried a refresh and it said "missing files" so i cant even do that...
Currently, I run Windows 7 Pro on dual 24" monitors, and life is good.
In Win 8, if I open the desktop tile, I presume that the default action is to open the full-screen desktop app on just 1 of the 2 monitors. I'm guessing that the "Start" screen remains on the 2nd monitor.
Can I have the desktop app open, full screen, across both monitors? Can I have icons for my so-called legacy programs littered across both monitors like I have them on the Win 7 desktop? Just to clarify, I am NOT asking about having the background wallpaper extend across both monitors. I want the actual desktop application to extend across both monitors.
I have two monitors. Some of my programs can take the whole screen, covering up everything including the task bar. In W7, I just used the MS clock gadget which I moved to the second screen so I could always see the time. Now in Windows 8.1 Update, I can see all the apps that I've pined to the active task bar, but I don't see the system tray with the time to the right. Doesn't have to be the task bar, of course -- could be a floating clock in the upper right or left or anywhere you like.
View 1 Replies View RelatedWhen moving my cursor between my two monitors, it stops at the border. To get to the other screen I either have to keep moving my mouse towards the border or move the cursor at high speed between the two. The issue occurs no matter where I cross, and does not appear to be related to the metro charms or multitasking.
My desktop just recently installed the Windows 8.1 Update (Pro 64-bit), and since then I have had this problem off and on. I do not know what causes it to happen. I have two monitors, side by side. A 1050x1680 monitor on the left, with a 1920x1080 monitor on the right. The top edges of these monitors are aligned.
This phenomenon is incredibly annoying, so any methods of stopping. I'd also be interested to know how and why this happens.
Just reinstalled Windows 8.1 and can't figure out what the deal is. I have a four monitor setup, and all of this worked perfectly before I reinstalled. I actually remember dealing with this issue before, but I couldn't remember how I fixed it.
Basically, with two monitors, everything works perfectly. The minute I connect my third monitor, it's like all the screen flicker, and then I get logged out and back to the start screen.
I've tried updating nvidia drivers but it doesn't work.
I have an ASUS mother board and don't use an graphics card.
I had two monitors and an HDMI cable plugged in. The short story is that the Intel drivers seem to get lost.
Windows installed normally until it went into to the final setup.
The program will switch to another screen at this point and picked a monitor and the HDMI to TV connection.
Unplugging the HDMI cable allowed me to finish.
My computer is hp envy dv6 7280sf notebook with 2 GPUs intel graphics HD 4000 and Nvidia Gefoce 630 M running windows 8 64x.
After making an free upgrade online for windows 8.1 which run successfully, both gpus were ok...
But after receiving a windows update with new drivers for intel graphics 4000 gpu , after install and restart , the computer freezes on blank black screen at windows startup with no mouse or anything only backlight.
So safemode was succeful but i figured that the update for windos update was the cause and graphics drivers were installed so i removed the drivers for intel graphics and itried to reboot the computer so the restart was succeful but the intel graphics card was unistalled and no drivers were automatically installed so i tried to download and install the drivers from hp and intel website for windows 8.1 however the install fails.
Automatic install from device manager failed both online and from computer and even from manual driver selection.
So therefore the install failed in safe mode , and the high def audio device ( on screen audio possibly) failed and the device was not recongnized (no drivers installed) so i'm stuck without anydrivers for the integrated gpu and the games are no longer able to run normally even if the nvidia card is on.
I tried downloading an installing Windows 8 drives but it failed to install also , for instance any new install of drovers seems to fail for me even for external usb hard drive.
I've got a bit of a strange issue that I haven't had with previous OSes on this PC. I'm running a Dell OptiPlex 380 with Win 8 x64 at the office and I have to run 2 video cards for all of my screens. I have a GeForce 8400GS in the PCI-E slot and a GeForce 6200 in the PCI slot.
Previous to the Win 8 install, it worked fine. Booted exactly as I had shut it off. Now, with 8 - it's killing my PCI-E card presumably when it puts the screens to sleep when I leave for the day. So I'm coming in to all of my windows being moved to the PCI card's monitor (only one hooked to it) and I have to reboot to get PCI-E card to come back.
If I check the screen properties, I see only the screen hooked to the PCI card. I've changed the setting in the BIOS for the first video card to Auto and also tried the PCI-E selection and it's the same either way.
Why on earth would it default to the PCI card rather than the PCI-E card?
i am on windows 8.i am using HP laptop.this is my ccc version.
i got 2 problems:well first one is that i can't update to windows 8.1 as the update always hang on 82% and after that my laptop
automatically shutsdown i don't know whats the reason is and that's why i am stuck at windows 8 till now although have 8.1 ISO but i don't want to install it as i have to erase my my windows 8 which came pres-installed so i will loose my genuine windows 8 .now i want to know what if i open the 8.1 installer and install it from a virtual tool like Deamon although it gives an option to keep files app setting safe but i fear that it would conflict with 8 and i would have to format my laptop then ok now to the major problem i just recently purchased Watch Dogs and installed it.I played the first mission and got busted so the mission failed and it began to reload and then a error pops up saying watch dogs have stopped working upon googling i found out that this is due to DUAl AMD Graphics so they stated that i should disable it but i cant find any option of disabling DUAL Graphics.
I got a new ASUS G750jx laptop two weeks ago and have been having crashes since the first day.
So far I've tried various hardware diagnostic tools:
Memtest - ran it for 19 hours in multi-thread mode, did 11 passes and had no errors
Intel diagnostic tool - found no errors
Seatools - had no errors
Fumark, 3dmark - without troubles
Ran system with driver verified enabled, had crashes, but all of them related to nt kernel and don't really give much information ( i had updated to windows 8.1 at that time )
Couple of days ago reseted everything back to factory settings and had more luck getting references to specific drivers in minidumps, like sortport.sys, dxgkrnl.sys and nvlddmkm.sys. Obviously tried all newest drivers from the manufacturer website, but problems still persist.
Unfortunately I've removed latest dumps, so I'm attaching previous ones : [URL] ....
And and small output from sf tool, too bad cannot go back and get a better one : [URL] ....
I have an Asus laptop that has recently been migrated from Windows 8.0 to Windows 8.1. I had few issues with Windows 8, after I got used to how it functions. Now, it usually takes 8-10 boot tries to make it through all the freezing issues before I get a successful boot. It rarely stops at the same place in the boot cycle. I have tried to use the Windows troubleshooter, selecting the restart issues, but it did not find any issues needing to be resolved. I have updated the drivers using driverscan, and it did update 31 drivers, but did not effect any changes to the freezing/lockups. I have configured the PC to create a complete dump upon lockups, but have not restarted the PC after the change since it takes so many tries to get to a workable configuration. I am attaching the SFdebug file as an attachment to this post.
View 5 Replies View Relatedgraphic card : GT 740m
i play a browser game on chrome named begone nplay with my charger plugged in i get 100-130 fps but whenever i unplugged it it drops to like 20-40 fps . i checked power settings and its always on high performance .
how can i know GPU activity ?
i like a lot process hacker , i have the last version and under Windows 8.1 pro 64bit ,system information gpu is empty (there is always 0% activity
is there a program that let me monitor?
I just decided to turn loose Windows 8 RP on "bare metal" here as opposed to a VM. I didn't even bother to mess with video under a VM, but with the bare metal install, I've run into some trouble.
At first, media player didn't seem to play anything, including .wmv files. Messing around, I unchecked the "Direct X acceleration" box and that allowed it to play .wmv files. However, it still won't play .mp4 files -- no video, just sound, and Media Player will hang trying to exit.
It did this with a clean install with only the Windows supplied video driver. My video card has been obsoleted by AMD now (HD 4200 chipset) and I couldn't use the new Windows 8 preview driver package, but I did try installing the AMD 12.4 driver in Win7 compatibility mode. That worked fine it seems, but it still won't play .mp4 files. Turning the Direct X acceleration back on still kills .wmv playback as well.
Win7, both x64 and 32-bit played .mp4 files fine right out of the box on this machine.
I've tried to set up a dual monitor for Windows 8.
This is what happens:
Note: If i set it as the tv for the main screen it works fine?
I have the following graphics card Gigabyte GeForce GTX 650 Ti Windforce 2X NVIDIA Graphics Card - 2GB installed on the system in my sig, what are the correct BIOS setting for the GPU, The options are: PCI Slot, PEG, PEG1, PEG2 and PEG3
View 7 Replies View RelatedI'm having issues with one of my GPU's fans (it features a dual-fan cooling) and will have to fix it soon. The problem is, it's making an annoying noise and I was thinking if I could just block it for the time being, however brutally that sounds.
So, the question is - provided the GPU doesn't reach critical temperatures (I'm going to monitor this obviously) - would this create any additional risks, like overcurrent or something? (I don't play games, but it's a HD6950, so it does emit a lot of heat).
I actually think it's integrated, how do I do it? According to running a random game on systemrequirementslab.com (Dead Island), my dedicated video RAM is 32mb. It's not a custom built, I bought it from the store.
Here are specs according to dxdiag:
System Info:
Operating System: Windows 8 64-bit (6.2, Build 9200)
System Manufacturer: Dell Inc.
System Model: Inspiron 5323
BIOS: A08
Processor: Intel(R) Core(TM) i3-3217U CPU @ 1.80GHz (4 CPUs), ~1.8GHz
Memory: 6144MB RAM
Page file: 3252MB used, 5310MB available
DirectX Version: DirectX 11
[Code] .....
I am on my work computer, a DELL desktop with Windows 8.1, and I've been using a dual monitor setup for months, both with Windows 8 and 8.1. One monitor is connected via the VGA input, and the other is through a VGA to HDMI adapter. Again, they've been working flawlessly for months. It was a plug 'n play setup that took a minute and never had an issue.
I came in today and the second screen was blank. In the screen setup menu it recognized it and allowed me to adjust between extending, mirroring, etc. But after I unplugged it and plugged it back in, it no longer recognizes it. It simply cannot find a second monitor plugged in. Both screens work when plugged directly into the VGA port separately but not when plugged in the way they've worked for months.
