I've been looking at some of the MATROX graphic cards for multi-monitor output -- up to 8 possible !!
Now any decent software to run these -- the standard software seems OK at running TWO monitors but I want to be able to run several more. You can run more but it gets a bit complicated managing this from within the standard windows system itself.
Five Best Tools for Managing Your Multi-Monitor Setup
I have a brand-new HDCP supporting monitor (native resolution 1920 x 1080,) on which I play the latest blu ray movies from the computers built-in blu ray drive, and a 9 year old flat screen non-HD plasma TV (on which I watch You Tube, BBC iPlayer and 4OD, streamed from the PC via a VGA cable,) both connected to my GT610 NVidia graphics card.
It seems I can only get them at the same resolution. My desktop does however have it's own on board graphics processor. Is it possible to run these two devices at different resolutions? (Since the ancient flat screen can only handle resolutions up to 1600 x 1200.)
ASUS P8 Z77-V LK mobo has 1 each VGA, HDMI, DVI-D & Display
At first I was not confused thinking I could use VGA or DVI for my monitor and HDMI or VGA for my TV
Then I started reading about 'Display Port' and confusion set in.
1. -> Can I just use HDMI & DVI off the board at the same time to use 2 monitors ?
2. -> or Do I have to use an adapter and 'Display Port' for the 2nd monitor ?
I have just rebuilt my PC and decided to make the jump from Windows XP to Windows 8. The jump has not been smooth, but it looks like I have ironed out my biggest problem (incorrect installation due to not creating a system partition therefore Windows 8 = no DVD, no boot; rookie error).
Now I am stuck with an issue - windows detects my only screen as more than one. Sometimes it thinks I have two, more often it thinks I have 3 or 4. Installing the current nVidia drivers did not work.
What I have at the moment is 2 generic non-PnP monitors and 2 generic PnP monitors detected, according to device manager. nVidia control panel calls them Dell SX2210, VGA display, (i can't recall the 3rd one, I'm on my laptop now), and TV. Windows display setup calls two of the SX2210, and the other two are either generic non-PnP or PnP monitors. In nVidia control panel it looks as though I have a clone setup (2 screens enabled) with the Dell SX2210 and the VGA display. In windows display setup it looks as though I have a clone setup (2 screens enabled) with Dell SX2210 and generic monitor.
I have repeatedly unchecked the secondary monitors in both nVidia control panel and windows display setup, leaving me with what should be a single monitor arrangement and 3 disabled monitors. This works until I restart my computer, which then reverts back to what it was before. This is OK as a workaround most of the time, but sometimes when I boot up the computer it detects the wrong screen as the primary and I get a monitor which goes to power save mode. The solution to this is Win Key + P and change the display selection while blind, which works now I know how. Sometimes my screen will refresh (installing programs or drivers) and I get the same result. Detect displays also results in no signal to my monitor.
Currently using DVI from the graphics card to DVI on the monitor.
System specs:
CPU: Intel 3570K (stock clock)
MB: ASRock Extreme4 Z77
RAM: 4 x 4GB 2133 GSkill
VIDEO: Gigabyte GTX260 OC
MONITOR: Dell SX2210 @ 1920 x 1080
OS: Windows 8 64bit
*Yes I know the 260 is an older card, it has come from my old system for economics reasons (to be upgraded later), but it was working perfect on that machine.
I'm building a system for cryptocoin mining, and am having a little problem with getting Windows 8.1 (home, not pro) to run the 3rd card (GPU) My equipment is:
Gigabyte 990 FXA UD3 MOBO
AMD Vishera CPU
2x4 gig Corsair Ram
3x Sapphire r9 280x Video cards
1000w Corsair PSU
Scandisk SSD
All parts are brand new.
Here is the problem... everything boots just fine and runs with 2 of the GPU's installed. I have the latest AMD 13.12 drivers, and the AMD APP SKD installed. When I add the 3rd GPU though, windows will auto detect it as a Radeon 7900 with the caution sign, AND/OR a r9 200 series card, also with the caution sign, most times BOTH. Then it randomly freezes the system. A couple of times I got it to run long enough just by luck I guess, to install the 13.12 drivers on the 3rd GPU, but then in a few minuites the system would freeze again.
2 GPU's run just fine, the problem only shows up when the 3rd card is installed, and it happens on any of the 4 16x slots, or both 1x slots on the MOBO. It doesn't matter if the GPU's are directly on the MOBO, or on 1x16 risers. There are plenty of folks running this set up with up to 6 GPU's, so I know it can be done, but I must be missing something somewhere in the windows set up.
Just reinstalled Windows 8.1 and can't figure out what the deal is. I have a four monitor setup, and all of this worked perfectly before I reinstalled. I actually remember dealing with this issue before, but I couldn't remember how I fixed it.
Basically, with two monitors, everything works perfectly. The minute I connect my third monitor, it's like all the screen flicker, and then I get logged out and back to the start screen.
I've tried updating nvidia drivers but it doesn't work.
In a few weeks (I can't wait! ) I will replace my laptop with the Surface Pro.
Right now, though, I have my laptop connected to two monitors: One via VGA and other via DVI. I'm running Windows 8 Pro x64, so this all works great.
So the big question is whether it is possible to have multi-monitor support via the one-and-only DisplayPort that is on the Surface Pro? If so, what--if any--additional hardware would I need?
When I'm docked at home and using my Surface Pro as laptop, I really need to keep the functionality of using both external monitors (one is 31" and the other 29"). I would really hate to go back to only being able to use one.
I'm currently running Windows 8.1 Update with an NVidia 660TI with two DVI monitors at 1920x1200 and a 1080p TV from the HDMI output. I'm having trouble with the 1080p TV in that when I drag an application (Store or Win32) onto the screen, the top and bottom is truncated when I maximise it. For example, if I drag Windows Media Player over to the TV and maximise it, the play, forward and rewind buttons when visible are cut in half at the bottom of the screen.
View 1 Replies View RelatedI have an ASUS mother board and don't use an graphics card.
I had two monitors and an HDMI cable plugged in. The short story is that the Intel drivers seem to get lost.
Windows installed normally until it went into to the final setup.
The program will switch to another screen at this point and picked a monitor and the HDMI to TV connection.
Unplugging the HDMI cable allowed me to finish.
Currently, I run Windows 7 Pro on dual 24" monitors, and life is good.
In Win 8, if I open the desktop tile, I presume that the default action is to open the full-screen desktop app on just 1 of the 2 monitors. I'm guessing that the "Start" screen remains on the 2nd monitor.
Can I have the desktop app open, full screen, across both monitors? Can I have icons for my so-called legacy programs littered across both monitors like I have them on the Win 7 desktop? Just to clarify, I am NOT asking about having the background wallpaper extend across both monitors. I want the actual desktop application to extend across both monitors.
I have two monitors. Some of my programs can take the whole screen, covering up everything including the task bar. In W7, I just used the MS clock gadget which I moved to the second screen so I could always see the time. Now in Windows 8.1 Update, I can see all the apps that I've pined to the active task bar, but I don't see the system tray with the time to the right. Doesn't have to be the task bar, of course -- could be a floating clock in the upper right or left or anywhere you like.
View 1 Replies View RelatedWhen moving my cursor between my two monitors, it stops at the border. To get to the other screen I either have to keep moving my mouse towards the border or move the cursor at high speed between the two. The issue occurs no matter where I cross, and does not appear to be related to the metro charms or multitasking.
My desktop just recently installed the Windows 8.1 Update (Pro 64-bit), and since then I have had this problem off and on. I do not know what causes it to happen. I have two monitors, side by side. A 1050x1680 monitor on the left, with a 1920x1080 monitor on the right. The top edges of these monitors are aligned.
This phenomenon is incredibly annoying, so any methods of stopping. I'd also be interested to know how and why this happens.
My computer is an HP Laptop with a 17" screen. Today I connected a stand a lone monitor that is about 22". I've managed to get the resolution for the Laptop back to standard or native resolution.
However I'm going around in circles trying to get the larger monitor to it's proper resolution. How might I go about doing this and get the larger to respond independently from the Laptop Monitor?
Do I need some software to accomplish this or what?
So I'm running 2xR9 290X (crossfire) with 3xQnix Qx2710 monitors. One of the qnix monitors was purchased with HDMI/DisplayPort connectors along with the usual DVI connector (normally these monitors only come with the D-DVI input)
I had a 2 monitor (with just the two DVI-only monitors) setup for a while that was working fine.
Since installing the third monitor I'm experiencing several weird things:
- On boot, until the Windows login screen comes up (Windows 8.1), there is nothing on the non-primary DVI monitor (so my setup is my primary monitor is one of the two DVI monitors, and then the left and right monitors is another DVI-only and the DP monitor).
- If the monitors go to sleep, or I put the computer to sleep and wake it up, any windows that were on the non-primary DVI monitor are moved over to the primary DVI monitor. Windows on the DP monitor do not move in this configuration.
- Within CCC, after sleep / monitors off, I have to restart CCC's control of the color settings for the non-primary DVI monitor. (I'm forgetting what the actual button says, but it's the button under the Display color controls settings where you can manipulate the R/G/B channels - I have to use the GPU for color matching since the monitors don't have any inherent ways to change R/G/B levels
If I only connect the two DVI monitors this is not an issue.
If I connect one DVI and the DP monitor, after sleep/wake any windows that were on the DP monitor are moved over to the primary monitor (again, note that this didn't happen when all 3 monitors were connected).
I have tried the newest version of CCC, as well as the current beta version - same behavior in both.
I have tried using HDMI instead of DP - same behavior
Aspects of this sound similar to the issues discussed in this post : [URL] ......
What I don't understand is why the second DVI monitor is acting so oddly when all 3 monitors are connected. Why would there be no picture when the computer boots?
My computer is hp envy dv6 7280sf notebook with 2 GPUs intel graphics HD 4000 and Nvidia Gefoce 630 M running windows 8 64x.
After making an free upgrade online for windows 8.1 which run successfully, both gpus were ok...
But after receiving a windows update with new drivers for intel graphics 4000 gpu , after install and restart , the computer freezes on blank black screen at windows startup with no mouse or anything only backlight.
So safemode was succeful but i figured that the update for windos update was the cause and graphics drivers were installed so i removed the drivers for intel graphics and itried to reboot the computer so the restart was succeful but the intel graphics card was unistalled and no drivers were automatically installed so i tried to download and install the drivers from hp and intel website for windows 8.1 however the install fails.
Automatic install from device manager failed both online and from computer and even from manual driver selection.
So therefore the install failed in safe mode , and the high def audio device ( on screen audio possibly) failed and the device was not recongnized (no drivers installed) so i'm stuck without anydrivers for the integrated gpu and the games are no longer able to run normally even if the nvidia card is on.
I tried downloading an installing Windows 8 drives but it failed to install also , for instance any new install of drovers seems to fail for me even for external usb hard drive.
I've got a bit of a strange issue that I haven't had with previous OSes on this PC. I'm running a Dell OptiPlex 380 with Win 8 x64 at the office and I have to run 2 video cards for all of my screens. I have a GeForce 8400GS in the PCI-E slot and a GeForce 6200 in the PCI slot.
Previous to the Win 8 install, it worked fine. Booted exactly as I had shut it off. Now, with 8 - it's killing my PCI-E card presumably when it puts the screens to sleep when I leave for the day. So I'm coming in to all of my windows being moved to the PCI card's monitor (only one hooked to it) and I have to reboot to get PCI-E card to come back.
If I check the screen properties, I see only the screen hooked to the PCI card. I've changed the setting in the BIOS for the first video card to Auto and also tried the PCI-E selection and it's the same either way.
Why on earth would it default to the PCI card rather than the PCI-E card?
i am on windows 8.i am using HP laptop.this is my ccc version.
i got 2 problems:well first one is that i can't update to windows 8.1 as the update always hang on 82% and after that my laptop
automatically shutsdown i don't know whats the reason is and that's why i am stuck at windows 8 till now although have 8.1 ISO but i don't want to install it as i have to erase my my windows 8 which came pres-installed so i will loose my genuine windows 8 .now i want to know what if i open the 8.1 installer and install it from a virtual tool like Deamon although it gives an option to keep files app setting safe but i fear that it would conflict with 8 and i would have to format my laptop then ok now to the major problem i just recently purchased Watch Dogs and installed it.I played the first mission and got busted so the mission failed and it began to reload and then a error pops up saying watch dogs have stopped working upon googling i found out that this is due to DUAl AMD Graphics so they stated that i should disable it but i cant find any option of disabling DUAL Graphics.
My setup is :-
Windows 8.1, 64 bit;
Asus RAIDR Express PCIe SSD;
Asus GT630-SL-2GD3-L GPU;
Asus SABERTOOTH Z97 MARK 1 Motherboard, BIOS version 0602, (the first version).
I have two monitors, a Dell u2412m which is plugged into the DVI socket on the GPU, and an iiyama XB2776QS which is connected to the DisplayPort socket on the motherboard. This was the only way I could find to get each monitor to use the maximum resolution it is capable of.
Whenever I open a program I have no idea on which monitor it will be displayed, sometimes a program will display in the iiyama, but the next time I open it I can see it on the Dell. I also find that if I switch the monitors off for a few hours, the next time I switch them on the programme might be displaying in a different monitor.
I am not sure if this is because I am not using the new, horrible, Metro style which Microsoft thought to introduce, or something else. I did try a piece of software called MurGeeMon, but this did not solve the problem.
Could it be because one of my monitors is connected to the GPU and the other to the MoBo?
graphic card : GT 740m
i play a browser game on chrome named begone nplay with my charger plugged in i get 100-130 fps but whenever i unplugged it it drops to like 20-40 fps . i checked power settings and its always on high performance .
how can i know GPU activity ?
i like a lot process hacker , i have the last version and under Windows 8.1 pro 64bit ,system information gpu is empty (there is always 0% activity
is there a program that let me monitor?
I just decided to turn loose Windows 8 RP on "bare metal" here as opposed to a VM. I didn't even bother to mess with video under a VM, but with the bare metal install, I've run into some trouble.
At first, media player didn't seem to play anything, including .wmv files. Messing around, I unchecked the "Direct X acceleration" box and that allowed it to play .wmv files. However, it still won't play .mp4 files -- no video, just sound, and Media Player will hang trying to exit.
It did this with a clean install with only the Windows supplied video driver. My video card has been obsoleted by AMD now (HD 4200 chipset) and I couldn't use the new Windows 8 preview driver package, but I did try installing the AMD 12.4 driver in Win7 compatibility mode. That worked fine it seems, but it still won't play .mp4 files. Turning the Direct X acceleration back on still kills .wmv playback as well.
Win7, both x64 and 32-bit played .mp4 files fine right out of the box on this machine.
I've tried to set up a dual monitor for Windows 8.
This is what happens:
Note: If i set it as the tv for the main screen it works fine?
I have the following graphics card Gigabyte GeForce GTX 650 Ti Windforce 2X NVIDIA Graphics Card - 2GB installed on the system in my sig, what are the correct BIOS setting for the GPU, The options are: PCI Slot, PEG, PEG1, PEG2 and PEG3
View 7 Replies View RelatedI'm having issues with one of my GPU's fans (it features a dual-fan cooling) and will have to fix it soon. The problem is, it's making an annoying noise and I was thinking if I could just block it for the time being, however brutally that sounds.
So, the question is - provided the GPU doesn't reach critical temperatures (I'm going to monitor this obviously) - would this create any additional risks, like overcurrent or something? (I don't play games, but it's a HD6950, so it does emit a lot of heat).
I actually think it's integrated, how do I do it? According to running a random game on systemrequirementslab.com (Dead Island), my dedicated video RAM is 32mb. It's not a custom built, I bought it from the store.
Here are specs according to dxdiag:
System Info:
Operating System: Windows 8 64-bit (6.2, Build 9200)
System Manufacturer: Dell Inc.
System Model: Inspiron 5323
BIOS: A08
Processor: Intel(R) Core(TM) i3-3217U CPU @ 1.80GHz (4 CPUs), ~1.8GHz
Memory: 6144MB RAM
Page file: 3252MB used, 5310MB available
DirectX Version: DirectX 11
[Code] .....
I am on my work computer, a DELL desktop with Windows 8.1, and I've been using a dual monitor setup for months, both with Windows 8 and 8.1. One monitor is connected via the VGA input, and the other is through a VGA to HDMI adapter. Again, they've been working flawlessly for months. It was a plug 'n play setup that took a minute and never had an issue.
I came in today and the second screen was blank. In the screen setup menu it recognized it and allowed me to adjust between extending, mirroring, etc. But after I unplugged it and plugged it back in, it no longer recognizes it. It simply cannot find a second monitor plugged in. Both screens work when plugged directly into the VGA port separately but not when plugged in the way they've worked for months.
How do I get "Screen Resolution" (on desktop, right click and select Screen Resolution) to show my main monitor as "1"?
View 5 Replies View RelatedI just purchased a new windows 8 PC. I was attempting to hook the computer up to my tv through hdmi (the pc has no VGA input) and when I went through the normal paces to put the display on my tv (display desktop only on 2), the signal did not transfer and there is no display on either my tv or pc! how to revert the display back to my pc monitor without being able to see anything? Acer support was less than useful. It's an acer aspire z3-605 all-in-one pc.
View 5 Replies View RelatedI've noticed that whenever I unplug my charger my brightness dims down to a point where I know its on, but I can't use it. Usually I have to put my computer to sleep and turn it back on to get it to fix. Also, the brightness wont adjust in anyway when its on. I've tried the function keys and the setting in the side bar. I have a toshiba laptop running windows 8.1 . I also have recently completely wiped it thinking it was a virus of some sorta with no change.
View 1 Replies View RelatedMy Sapphire AMD HD 7870 just bit the dust so it has been sent back with an RMA. I had hoped to replace it with an ASUS AMD HD 3850 but Windows 8.1 will not work with it. There is an error message on a blue screen something about a header (I don't have the exact error message today).
I suspected it was a driver problem so uninstalled the existing driver and tried to install the latest AMD one. I can uninstall OK but as soon as I reboot the Microsoft driver installs itself giving me no opportunity to install the AMD one.
Today, I got a new graphics card for my computer that is about 5 years old. Here are my specs:
Dell Inspiron 530
Intel Core 2 Duo e2500 2.33 GHz Processor
NEW GPU: MSI Geforce GT 440 (N440GT)
OLD GPU: NVIDIA Geforce 8600GT
3GB ram
300 watt power supply (unsure of 12V ratings)
Windoes 8 Pro 64bit
I installed my GT440 into my computer today, and the card worked fine when there was no drivers installed. I uninstalled my older drivers from my 8600 and installed drivers for the 440. When I restarted, I got the BSOD with an error message saying VIDEO_DTR_FALIURE. What does this message mean, and what can I do to fix this BSOD problem? This didnt happen on my old card, but it does on my new card? Is there a problem with my power supply, or is it an issue with the drivers?