I've recently installed a dual boot, Windows 7 and Windows 8. The installation went fine but then after a very short time my Windows 8 Screen goes black. I had to press the power button to exit. When again rebooting into Windows 8 the "blue window" shows and the spinner goes around for about 20 seconds, then all goes black.
I've checked the Power settings and ensured the "Turn off display" was "never". I also updated my Video drivers thinking that might be the problem. Both to no avail. I've done a "Refresh" and a "Reset (which took 3 hrs). Again, all was fine for a short time, but while exploring the OS, again the black screen. What else I could try to fix this Windows 8 problem.
I have installed Win 8 on a slave HDD. Every time I boot to Win 8 my dual boot screen is gone,also Win 7 activation. Then it boots directly to Win 7. To go back to Win 8 I have to use EasyBCD. Once in Win 8....activation for Win 7 gone again ....
I've recently installed a dual boot, Windows 7 and Windows 8. The installation went fine but then after a very short time my Windows 8 Screen goes black. I had to press the power button to exit.
I've checked the Power settings and ensured the "Turn off display" was "never". I also updated my Video drivers thinking that might be the problem. Both to no avail. I've done a "Refresh" and a "Reset (which took 3 hrs). Again, all was fine for a short time, but while exploring the OS, again the black screen.
I followed... re-formatting the hard drive during the new installation, trying generic video drivers and doing Resets and Refreshes. None of that worked and still doesn't. The installations do complete as before, but I don't have enough time to download new updates to perhaps correct whatever problem(s) there are before all goes black after a few minutes. As I stated before I have to hold down the power button to exit.
If this is a clue, once the screen goes black and I revert back to Window7, before loading, the File System on ALL drives, including C and the Windows 8 partition has to check for consistency before Windows 7 boots up.
I've been quite busy and haven't had a chance to try re-installing again until now. Thinking the problem might have been the actual drive I used for previous attempts (it was a SATA external drive which by the way I previously used for a dual boot Vista/with Win7), I then created new partitions on 2 different USB connected external drives and attempted to install. It wouldn't do the install on either one. I received messages "Setup does not support disks connected through USB or Firewire,.... my USB drives are connected directly to computer not a hub. So I'm forced to use the SATA created partitions for the installations. (Disk 1)
If it makes a difference, through Disk Management, I've deleted the Windows 8 installs from those partitions then re-created a "New Simple Volume" before trying again. I even tried creating another partition on C but it wouldn't allow an installation saying it was a dynamic drive. Prior to me creating that additional C partition all were Primary but now they're all Simple Volumes as per the color codes.
I have two OEM Windows 8 installation disks, I've tried both.
Since a few days my Internet Explorer 11 (newest version) crashes after a few short browsing time on my Dell Venue 8 Pro. There are specific mostly high crowded sites I can go to and it will freeze, or just if I tab/surf fast enough for example click links in a row. I had the same problem 3 months ago, and the only solution which worked was to reset Windows, install everything new. It worked so far until a view days ago, it began again to show the same behavior: slow site rendering, and freeze after a short time. The behavior is described for example here too by other users:
IE11 crashing constantly after upgrading to 8.1 - Page 2 - Windows Phone Central Forums [URL] .....
I already tried the following steps without luck:
- reset IE settings to default - cleared all cache/cookies/settings - deactivated every plugin (I didnt have any special installed at all, I just deactivated the default ones one Flash, adobe pdf, Intel, to see if it worked, it didn't) - gave "all installed applications" rights to c: - did a sfc /scannow - cleared Windows Store cache (wsreset) - enable software rendering (which though doesnt have impact on metro ie I think)
When I boot or reboot my PC, it is a slow process, the time with the blue window and the spinning circle is only about 5 seconds, but then there is a pause of 30-35 seconds where absolutely nothing is going on. Black screen, no activity at the SSD or at the net. After this my USB mouse and keyboards wake up, and only a few seconds later my PC is running normally.
I have allways (in windows 8) had that black screen, but only for a few seconds. After Windows 8.1 this "dead screen" just getting longer and longer. I have had it for some times, but I used to use Intel Rapid Start, so I did not care. Now I got som faster ram, and Intel Rapid Start don't work with this ram, so now I have to boot every time, and now I'm not so happy with this long pause in boot.
What is Windows 8 doing in this time? How to eliminate it (or just get it reduced)?
Okay so yesterday, I was using my laptop (Asus k45vm) and things started getting laggy. It got to the point were I had to restart it and after that was when everything went downhill. I loaded up to the Windows logo and the spinning dots, didn't get further than that. So I restarted again and mashed the f8 key (I later tested out all the keys), laptop scanned and "fixed" the problem. Still didn't work. So then in a fit of rage, I pulled the battery out, it loaded to the logo screen a few times after, but now right after the Asus boot screen, the screen goes black (without any cursor). F8 (and the rest) doesn't work anymore (no more boot screen). But if I wait for 5 min , a blue screen with:Recovery
Your PC needs to be repaired
The Boot Configuration Date file is missing some required information.
File:BCD
Error Code: 0xc000000d
You'll need to use the recovery tools on your installation media. If you don't have and installation media, contact your system admin or PC manufacturer. And then it shuts down in a minute.
So I created a bootable usb with win 8, Fat 32, uefi and all that , but it still goes to the black screen followed by the error. At this point I doubt that I can get into advanced boot options.
Even though I boot the laptop with the usb plugged in, it still says :You'll need to use the recovery tools on your installation media. If you don't have and installation media, contact your system admin or PC manufacturer.
I just got a refurbished ASUS K75DE laptop, and it came with Windows 8 on it. I am wanting to run a dual boot with Win7, so I disabled fast-boot just fine, and went into the UEFI BIOS and disabled the secure boot.
While I was there, I did like I have always done and set a BIOS boot-up password. I then proceed to boot to my Win7 installer USB Flash drive, but I was running low on battery power so I aborted the install and shut the computer down to try again later.
Now however when I get into BIOS to select boot priority, all options are grayed out except for system time and a few other non-essentials. At the bottom of the first BIOS screen it says "User Level : User" and I can't seem to find a way to reverse this issue. So now I'm stuck, can't boot to anything but the HDD because it is first by default.
I have installed Blue 8.1 on a separate drive in my system along side 8.0. When I restart the 8.0 boots unless I manually select the 8.1 drive in bios. How can I alter the Boot menu to add the option to boot from either OS?
Late last Fall I bought a new Desktop, an HP H81414, with Windows 8 installed with the intention of installing Windows 7 on an SSD. I migrated Window 8 to an SSD, removed that from the system, installed new SSD and put Windows 7 on it. Both worked fine. I wound up with 2 SSD's. capable of running on the EFI BIOS machine with Secure Boot turned off. I later bought a new laptop with Windows 8. I found the Win 8 with Classic Shell to be very acceptable.
What I would like to do now ,if possible, is to mount both SSD's in the HP case and switch to either one of them at boot.
I don't know either this is the right place to ask or not. I just having my 2nd monitor. I just want to ask it is possible for me to play game and browsing the internet at the same time? The 2 monitors hooked up to the same graphic card. both of them is 23". So it is possible to play a full screen game on one monitor while also browsing the internet on the other monitor? I've tried it but whenever I click anything in the second monitor the game minimizes. My settings are set to extended display and I'm guessing that's the reason this happens but are there any settings I can change to make this possible. Basically having the 2 monitors be independent of each other. and this is my computer main spec:-
I had windows 7 running on my computer. When windows 8 came out I used a second harddrive as the windows 8 installation drive. Windows 8 automatically setup a dual boot system where every time I started the computer it took me a windows screen where I could select either windows 7 or windows 8. This has been going on since Windows 8 was released.
I decided it was getting old so I decided it was time to remove the old windows 7 harddrive. I tried doing it inside the windows 8 dual boot screen but could not find an option. So I decided to reformat the windows 7 harddrive. I did this in command prompt mode. After doing so when my computer restarted it said it could not find any harddrive to boot. Windows 8 is installed on the other harddrive, the one that was not reformatted. So how do I get it to start using that harddrive as the boot drive? I checked my bios and even physically disconnected the old HD that had windows 7 on it, but none of that seemed to work even though the Windows 8 HD is definitely in the boot order in the bios.
I am dual booting Windows 8 and win7. I actually have Windows 8 installed on its own hard drive and win 7 installed in its own hard drive. The win7 hard drive has been in use for the past 2 years and I have had Windows 8 running for about a week now. I purchased another hard drive for Windows 8 and left the old Win7 as it was.
I also have 3 other hard drives in the system. Everything is formatted NTFS.
So my system is as follows
Drive C - Boot Drive - I physically swap out the dedicated hard drive for Win 8 or Win 7 Drive D - internal 250 GB sata drive Drive F - internal 250 GB sata drive Drive H - internal 250 GB hard drive.
I have been running this config for about 2 years under Win7 with no problems.
The problem that I have now is when I swap the boot drive and boot up a different OS than last time (Like booting Windows 8, powering down system, swap boot drive, boot Win7) the system always says that there are problems on the 3 non-boot drives. It runs chkdsk(it least that is what it look like) and processes the 3 non boot disks one at a time which take about 10-12 minutes for all 3. Most of the time it finds no problems, but about 1 out of 5 boots will find a problem with one of the disks and then fixes it. The disks seem to be OK while I am running. I then power down and swap boot drive and reboot the other os and we start all over again. I am powering the system completely down for each reboot to make sure that the disk cache is flushed.So far the disk problems have been fixed by chkdsk at boot, but I am sure the day will come when the disk cannot be fixed and I will loose data.
I cloned my existing Windows installation (8.1 pro, 32 bit) onto my new SSD. I got everything up and running, and I still have my old Windows installation on one of the partitions of my HDD.
Can I turn this setup into a dual boot?
I think this could be useful, in case the new installation gets borked, or in order to run an effective malware scan on the SSD, etc.
I have recently bought a new system running Windows 8.1 64 bit.
After I played Cities in Motion 2 on Steam the problem first occurred. The screen freezes and one or two seconds late the system restarts. There is no BSOD.
Yesterday I played all day with no issues but today the problem happens regularly, even when just browsing the internet in one window.
Find attached the SF Debug tool zip file.
The system is still under warranty but I thought I would try here first before going back to they system builder.
I have windows 8 to go on my 320 GB USB harddrive and I would like to be able to boot from the disk a choose if I waht to boot from windows 8 to go or another partition where I have my ghost.
I'm not sure how to go about making a dual boot when it is a USB harddisk.
i had windows 7 installed and i installed windows 8 on my other partition and after some days i did a format on win7 partition but the dual boot menu is still there any solution to remove that ?
I'm having a hard time with WinPE 4.0. For starters, my USB is 128GB, which means I have to use exFAT - according to some people, it should work, but others say it won't. So far no luck.
Also, it's my only USB and any way to boot both x86 and x64 WinPE 4.0 from it. Even if I have to use separate partitions, that would be fine.
Finally, I have to do this in UEFI mode.... BIOS won't work on the device I'm trying to boot to.
I have an older tower running W8.1 update 1 and Wxp - each OS is on a separate hard drive, when I boot the computer I get the choice of booting to W8.1 or earlier OS. I am now ready to remove the XP drive and delete all the information, my question is:
Is there a proper method to remove the choice of OS on the boot screen, or will it be removed if I just remove the hard drive with XP on it?
I have new pc that has windows 8 pro installed. I would like to dual boot with windows 7 because certain software for work is not compatible with win 8. I was reading that I can create a vhd from windows 8, boot to the windows 7 installation media and install win 7 to the vhd, then I have the option to select win 7 or 8. Am I missing something here or is it as easy as this? Also do I need Win 7 ultimate or will he professional one work? I do not want to partition the hard drive.
I set up a dual boot with Windows 7 and 8 and it is extremely slow up until the Windows 7 and 8 appear. From that point on both load quickly. Also under the Windows 7 icon it says "recovered". Otherwise eveerything seems to be functioning normally.
Well, I had a dual booted machine booting Windows 8 and Ubuntu.
Windows 8 was starting to play up so I decided to completely reset the computer. I backed everything up, booted to Windows 8 and hit the 'Reset PC' button.
After answering some questions (full erase, whole disc etc), it informed me that it was going to restart. I clicked accept.
Short Story: - Corrupted Windows 8 partition - Corrupted Windows 8 recovery partition
Long Story: Instead of rebooting back to anything, I got left sitting at a grub rescue prompt. From there I told it to boot windows 8. I then spent five minutes staring at the booting screen. Nothing happened.
I powered off and tried again, this time pointing grub rescue at the windows 8 recovery loader partition. Well, initially that looked like it worked. I got the nice metro UI, and chose 'reset this PC' It then informed me that the recovery partition was missing some files. The only other option was to shut down.
I tried booting just plain windows 8 again, but had the same problem as before (nothing happening), And now when I try to boot the recovery loader, Grub tells me the EFI file isn't where it expects it to be. (Interestingly, how are you meant to boot to this without having a non-windows bootloader?)
Additional Details: Computer: HP Envy M6-1206TX. Pre-installed with Windows 8. Bought about 1 month, 1 week ago.
The Questions: Since windows 8 came pre-installed, I don't have a Windows 8 disc, are there any possibilities for me to get back windows 8? (other than contacting the store I purchased it from)
After going through the license agreement, my interpretation is that I still have a license for Windows 8, but I am not under their limited warranty (due to dual booting). I do not wish to buy another license, as I already have one.
One last question: If you acquired the software on a disc or other physical media, your proof of license is the genuine. Microsoft certificate of authenticity label with the accompanying genuine product key.
Neither my laptop, nor the box, nor any of the paperwork provided in it had this 'certificate of authenticity.' I suppose that means I have no legal rights to the software. Who's fault is this, HP, Microsoft, or the store I bought it from?
I have previously posted about the recommended Windows OS for my new laptop... and Then I decided to install Windows 8.1 Pro alongside my previously installed Windows 7 Ultimate (32-bit)... Is it OK to install and dual-boot Windows 8.1 Pro with Windows 7 Ultimate?
And also tell me about the partition size allocations for both Windows, I have two partitions each of 24.7 GB for both the OSes, is this size worth applicable?
Didn't plan ahead Dual boot Windows 7 and 8. I only initially allowed 100 GB for my primary Windows 8 on a 2 TB drive. I'm hardly using the W-7 and now find myself out of space on the W-8 (C) I'd like to repartition to give (C) 1 TB and 1 TB for (D)
Is it possible to have two hard drives in the computer and to be able to choose which one to start with ?
I have in mind that one hard drive has all my normal programs and the other is used for Flight simulation program.
Both hard drives would have win 8 installed. If I could use one hard drive and partition it so the flight sim is on a separate partition. However, for two reasons I wouldn't want this as the flight sim with scenery requires a lot of Gigs. and secondly I believe that it would run faster on its own hard drive.
So. Is it possible to set up the computer to decide which Drive I wish to start ? and if so, how to set it up ?
My Old laptop died. Not a Harddrive issue it functions fine. I had Vista installed. I now have a new HP ENVY DV7. I would like to set up my new system to allow booting from either my old hard drive, or my new system. How to accomplish this?
So, previously I had Windows 8 and a system image of that drive. I want to dual-boot it with Win7, so I replace my Win8 with Win7, and reinstall Win8 on another partition. Can I restore my Win8 with the previous system image, or will it affect my Win7?
I have created dual boots before but in each case I did it the "usual" way by doing a fresh install of a second OS on a new drive (or new partition) and then letting the newest installation figure out how to arrange boot loaders or boot managers or whatever, i.e to figure out the dual boot parameters for me.
In this case I want to set up a dual boot using what is now 2 separate drives each with its own complete install of Windows. Of course, I can boot to one or the other by disconnecting the drive for the one I don't want to start up, but that is obviously a hassle.
Is there an easy way to set it up so that one of them (Win 8.1 pro) actually recognizes the other and asks me which one I want at boot up. I know if I re-install one of them I can do it, but I want to just set up the dual boot, and not touch either of the OS installations per se.
