I have Windows 8.1 PC, then i installed EaseUS Partition Master 9.3 (All Editions), So i am having seperate ISO of WinPE, so i like to know "How to install WinPE on PC" because i want to Create EASEUS 3.9.0 Bootable CD.
I am having all the files like this below.
1)--EASEUS Partition Master 3.9.0 2)--WinPE ISO image ( in this iso there is no SETUP file is there, so how i should install this WinPE) If i install WinPE then i am able to create EASEUS Bootable CD.
My computer shipped from the factory (Dell) with Windows 7 x64. I recently did a clean ('custom') install of Windows 8 Pro x64. The install went very well, no problems. To install Windows 8, I booted from a USB flash drive.
I actually have two licensed copies of Windows 8. The other copy is on a DVD. To test the functioning of my DVD drive, I tried to boot from the Windows 8 disk. The computer would not boot. My computer had no trouble booting from the USB flash drive version of my Windows 8 installer, obviously, but it won't boot from a disk version of same.
As a further test, I tried to boot my computer from my original factory Windows 7 install disk. The computer successfully booted from this disk.
I therefore concluded that my computer can boot from a disk made with WinPE 3, but it will not boot from a disk made with WinPE 4, even though it will boot from a USB flash drive made with WinPE 4. I tried to boot from other bootable disks made with WinPE 4 - none would boot the computer. Other bootable flash drives made with WinPE 4 have no problem booting my computer.
My computer is partitioned with a MBR and uses a BIOS. I made no changes to my BIOS settings, and unfortunately there will be no more BIOS updates for my computer.
Should I just accept that I cannot boot from disks made with WinPE 4, or is there some way around this? I'm not too broken up about this because, after all, I have no trouble booting from WinPE 4 flash drives. And disks are on the way out, anyway.
I just got a refurbished ASUS K75DE laptop, and it came with Windows 8 on it. I am wanting to run a dual boot with Win7, so I disabled fast-boot just fine, and went into the UEFI BIOS and disabled the secure boot.
While I was there, I did like I have always done and set a BIOS boot-up password. I then proceed to boot to my Win7 installer USB Flash drive, but I was running low on battery power so I aborted the install and shut the computer down to try again later.
Now however when I get into BIOS to select boot priority, all options are grayed out except for system time and a few other non-essentials. At the bottom of the first BIOS screen it says "User Level : User" and I can't seem to find a way to reverse this issue. So now I'm stuck, can't boot to anything but the HDD because it is first by default.
I have installed Blue 8.1 on a separate drive in my system along side 8.0. When I restart the 8.0 boots unless I manually select the 8.1 drive in bios. How can I alter the Boot menu to add the option to boot from either OS?
Late last Fall I bought a new Desktop, an HP H81414, with Windows 8 installed with the intention of installing Windows 7 on an SSD. I migrated Window 8 to an SSD, removed that from the system, installed new SSD and put Windows 7 on it. Both worked fine. I wound up with 2 SSD's. capable of running on the EFI BIOS machine with Secure Boot turned off. I later bought a new laptop with Windows 8. I found the Win 8 with Classic Shell to be very acceptable.
What I would like to do now ,if possible, is to mount both SSD's in the HP case and switch to either one of them at boot.
I had windows 7 running on my computer. When windows 8 came out I used a second harddrive as the windows 8 installation drive. Windows 8 automatically setup a dual boot system where every time I started the computer it took me a windows screen where I could select either windows 7 or windows 8. This has been going on since Windows 8 was released.
I decided it was getting old so I decided it was time to remove the old windows 7 harddrive. I tried doing it inside the windows 8 dual boot screen but could not find an option. So I decided to reformat the windows 7 harddrive. I did this in command prompt mode. After doing so when my computer restarted it said it could not find any harddrive to boot. Windows 8 is installed on the other harddrive, the one that was not reformatted. So how do I get it to start using that harddrive as the boot drive? I checked my bios and even physically disconnected the old HD that had windows 7 on it, but none of that seemed to work even though the Windows 8 HD is definitely in the boot order in the bios.
I am dual booting Windows 8 and win7. I actually have Windows 8 installed on its own hard drive and win 7 installed in its own hard drive. The win7 hard drive has been in use for the past 2 years and I have had Windows 8 running for about a week now. I purchased another hard drive for Windows 8 and left the old Win7 as it was.
I also have 3 other hard drives in the system. Everything is formatted NTFS.
So my system is as follows
Drive C - Boot Drive - I physically swap out the dedicated hard drive for Win 8 or Win 7 Drive D - internal 250 GB sata drive Drive F - internal 250 GB sata drive Drive H - internal 250 GB hard drive.
I have been running this config for about 2 years under Win7 with no problems.
The problem that I have now is when I swap the boot drive and boot up a different OS than last time (Like booting Windows 8, powering down system, swap boot drive, boot Win7) the system always says that there are problems on the 3 non-boot drives. It runs chkdsk(it least that is what it look like) and processes the 3 non boot disks one at a time which take about 10-12 minutes for all 3. Most of the time it finds no problems, but about 1 out of 5 boots will find a problem with one of the disks and then fixes it. The disks seem to be OK while I am running. I then power down and swap boot drive and reboot the other os and we start all over again. I am powering the system completely down for each reboot to make sure that the disk cache is flushed.So far the disk problems have been fixed by chkdsk at boot, but I am sure the day will come when the disk cannot be fixed and I will loose data.
I have a Microsoft Surface Pro 2 and I am running Windows 8.1 Pro Update 1.
I have been unsuccessful at building a WinPE image that provides BitLocker support. I searched around the internet and found many posts. Eventually, I ended up trying to build it with the various added packages I discovered in the various posts. However, in the end, none worked and this is the message I am getting after booting into my WinPE environment:
manage-bde.exe - Application Error
The instruction at 0xa20afa3b referenced memory at 0x0000013d. The memory could not be read. Click on OK to terminate the program
Here are the commands I eventually ended up using to build my WinPE image:
I have an older tower running W8.1 update 1 and Wxp - each OS is on a separate hard drive, when I boot the computer I get the choice of booting to W8.1 or earlier OS. I am now ready to remove the XP drive and delete all the information, my question is:
Is there a proper method to remove the choice of OS on the boot screen, or will it be removed if I just remove the hard drive with XP on it?
I have new pc that has windows 8 pro installed. I would like to dual boot with windows 7 because certain software for work is not compatible with win 8. I was reading that I can create a vhd from windows 8, boot to the windows 7 installation media and install win 7 to the vhd, then I have the option to select win 7 or 8. Am I missing something here or is it as easy as this? Also do I need Win 7 ultimate or will he professional one work? I do not want to partition the hard drive.
I set up a dual boot with Windows 7 and 8 and it is extremely slow up until the Windows 7 and 8 appear. From that point on both load quickly. Also under the Windows 7 icon it says "recovered". Otherwise eveerything seems to be functioning normally.
Well, I had a dual booted machine booting Windows 8 and Ubuntu.
Windows 8 was starting to play up so I decided to completely reset the computer. I backed everything up, booted to Windows 8 and hit the 'Reset PC' button.
After answering some questions (full erase, whole disc etc), it informed me that it was going to restart. I clicked accept.
Short Story: - Corrupted Windows 8 partition - Corrupted Windows 8 recovery partition
Long Story: Instead of rebooting back to anything, I got left sitting at a grub rescue prompt. From there I told it to boot windows 8. I then spent five minutes staring at the booting screen. Nothing happened.
I powered off and tried again, this time pointing grub rescue at the windows 8 recovery loader partition. Well, initially that looked like it worked. I got the nice metro UI, and chose 'reset this PC' It then informed me that the recovery partition was missing some files. The only other option was to shut down.
I tried booting just plain windows 8 again, but had the same problem as before (nothing happening), And now when I try to boot the recovery loader, Grub tells me the EFI file isn't where it expects it to be. (Interestingly, how are you meant to boot to this without having a non-windows bootloader?)
Additional Details: Computer: HP Envy M6-1206TX. Pre-installed with Windows 8. Bought about 1 month, 1 week ago.
The Questions: Since windows 8 came pre-installed, I don't have a Windows 8 disc, are there any possibilities for me to get back windows 8? (other than contacting the store I purchased it from)
After going through the license agreement, my interpretation is that I still have a license for Windows 8, but I am not under their limited warranty (due to dual booting). I do not wish to buy another license, as I already have one.
One last question: If you acquired the software on a disc or other physical media, your proof of license is the genuine. Microsoft certificate of authenticity label with the accompanying genuine product key.
Neither my laptop, nor the box, nor any of the paperwork provided in it had this 'certificate of authenticity.' I suppose that means I have no legal rights to the software. Who's fault is this, HP, Microsoft, or the store I bought it from?
I have previously posted about the recommended Windows OS for my new laptop... and Then I decided to install Windows 8.1 Pro alongside my previously installed Windows 7 Ultimate (32-bit)... Is it OK to install and dual-boot Windows 8.1 Pro with Windows 7 Ultimate?
And also tell me about the partition size allocations for both Windows, I have two partitions each of 24.7 GB for both the OSes, is this size worth applicable?
Didn't plan ahead Dual boot Windows 7 and 8. I only initially allowed 100 GB for my primary Windows 8 on a 2 TB drive. I'm hardly using the W-7 and now find myself out of space on the W-8 (C) I'd like to repartition to give (C) 1 TB and 1 TB for (D)
Is it possible to have two hard drives in the computer and to be able to choose which one to start with ?
I have in mind that one hard drive has all my normal programs and the other is used for Flight simulation program.
Both hard drives would have win 8 installed. If I could use one hard drive and partition it so the flight sim is on a separate partition. However, for two reasons I wouldn't want this as the flight sim with scenery requires a lot of Gigs. and secondly I believe that it would run faster on its own hard drive.
So. Is it possible to set up the computer to decide which Drive I wish to start ? and if so, how to set it up ?
My Old laptop died. Not a Harddrive issue it functions fine. I had Vista installed. I now have a new HP ENVY DV7. I would like to set up my new system to allow booting from either my old hard drive, or my new system. How to accomplish this?
So, previously I had Windows 8 and a system image of that drive. I want to dual-boot it with Win7, so I replace my Win8 with Win7, and reinstall Win8 on another partition. Can I restore my Win8 with the previous system image, or will it affect my Win7?
I have created dual boots before but in each case I did it the "usual" way by doing a fresh install of a second OS on a new drive (or new partition) and then letting the newest installation figure out how to arrange boot loaders or boot managers or whatever, i.e to figure out the dual boot parameters for me.
In this case I want to set up a dual boot using what is now 2 separate drives each with its own complete install of Windows. Of course, I can boot to one or the other by disconnecting the drive for the one I don't want to start up, but that is obviously a hassle.
Is there an easy way to set it up so that one of them (Win 8.1 pro) actually recognizes the other and asks me which one I want at boot up. I know if I re-install one of them I can do it, but I want to just set up the dual boot, and not touch either of the OS installations per se.
I get to the new win 8 graphical boot screen, but the timer is not working at all. I've tried to change the timer from the default 30 seconds to 15 seconds & back again with no success. It will sit on that boot menu for as long as I choose to wait before making a selection.
I have two hard drives One is a SSD and the other is a WD 64 MB cache 2 terabyte drive. I have Windows 7 installed on the SSD which works fine. I later, when I received it, installed Windows 8 on the other drive for a dual boot. It works, the screen comes up allowing me to choose between the OS's. Like I said picking 7 works fine but when I go into 8 it boots up, shows the Metro and is locked solid. I havent waited more than 5 mins but i get tired of it locking. I have 16 gigs of Kingston Ram, 2 ATI 6950 with combined 4 gigs. AMD 8 core and a ASUS motherboard. Everything was bought this year. Except for the Video cards. I am trying to update the ATI software but it is locked so i cant.
I've been doing the above ^^ for some time now. I've been using W8.1 as the main OS for my notebook. Yesterday I rebooted into Win7 to poke around. Every time that it said 'Starting Windows' it bluescreen (very rapidly) and restarted.
I tried the disc auto-repair, and this cut the bridge to W8.1 of course. When I tried Win7 it then said that there was another problem. The logon screen appeared, as if in safe mode, then produced numerous errors about being untable to log on or start logon services. I could not resolve this.
I eventually decided to try the manufacturer inbuilt restore of Win7 while leaving data alone. This seemed fine until it says 'preparing Windows for first use', then it said that the installation was interrupted (not by me or power use). I tried this several times but no use.
Shortened, I could not get back into Win8, I tried all the repairs, though it should only have been a bootloader issue, right? The Win8 bootloader will look back and see Win 7 and offer both. I formatted that partition, reinstalled Win8 on that partition, removed all data from the Win7 drive and then tried a complete reinstallation of the entire hard disk with the manufacturer restore disks. This worked.
I would like to poke around with W8.2 when it comes in the Spring. I need to understand what happened. My top two guesses are:
1. Minitool Partition manager, I suspected that program of being ... ruthless in hard drive partitioning and resizing in the past.
I'm trying to dual boot Windows 7 Ultimate 64-bit and Windows 8 Pro. I want to have each OS installed on separate Hard drives. I want the default OS to be Windows 7 (loads automatically) or goes to the boot manager screen and choose either Win 7 and Win 8.
I've been running Windows 7 on an SSD hard drive with a UEFI Boot. I'm looking to install Windows 8 on a WD Caviar Black 1 TB drive.
-Burnt Windows 8 to DVD to boot and install from. -Re-ordered boot order to boot from DVD -Windows 8 install starts -Windows 8 drive screen - format the WD Caviar Black 1 TB to install Windows 8 on. -ERROR Message appears - Can't find media location (I didn't write it down but will on next install I will update). Something like 0x00007B. The solution I found was to disconnect my Windows 7 drive (and all other hard drives).
(Issue: won't that affect the set up of the dual boot?)
-Disconnected Windows 7 drive and was able to install Windows 8. -After successful install of Windows 8 I re-started my system expecting to see the dual boot menu options. However, Windows 8 loaded directly. -Changed boot drive order to SSD (with Windows 7) then WD 1TB Drive (with Windows 8). However, Windows 7 then loaded directly. -I rebooted into Windows 8 and went to the boot order menu in Settings > Control Panel > System > Startup and Restore > (might be a few other tabs). The drop down box shows Windows 8 but no Windows 7.
So, I'm sure I did something wrong on the install. Any thoughts?
If the SSD is a UEFI boot should the WD 1TB (Win 8 install drive) be the same? Is it critical to have the Windows 8 drive connected while installing Windows 8 to the other hard drive? If so, I will have to solve the error message I get after formatting the WD 1TB drive during the Win 8 install. (I know not having the specific error code doesn't work - will update tonight with that info).
Also, I have a 2TB drive that I think has a MBR partition. Would that affect things? Should I even have that? I'll confirm that too. Just hoping to possibly get the ball rolling with answers.