How do you connect to another PC using remote access, I can connect to another computer at my house but I want to connect to my uncle's from Arizona to California. What IP adress do you write down because everyone has the same 192.168.1.1 so if i put that it will connect to another one in my house. Is there some other IP adress that I can use. How can i connect to his PC.
View 3 RepliesI am trying to configure Remote Desktop Access to work over the internet. Remote Desktop Access works on my local network.
Both of my computers are on Windows 7 Professionnal. My router is a Belkin F9K1002.
I followed the official widows tutorial. I forwarded the necessary port on my router (I switched from port 3389 to 50000, in case 3389 was blocked by my isp).
Every time I try to connect I get
"Remote Desktop can't connect to the remote computer for one of these reasons:
1)Remote access to the server is not enabled
2)The remote computer is turned off
3)The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled."
We have several remote systems that can all connect fine. I am having an issue with one box. It is a windows 7 home premium machine with netgear wireless nic. When I open mstsc to connect to a remote machine I put in the ip address and click on connect.I receive an immediate failure with the text "This computer can't connect to the remote computer. Try connecting again...blah blah"I have a server 2008 r2 with Network level authentication enabled. I have 8 other systems that are hardwired, at different geographic locations and all connect fine. I have not made any changes on the server side since this problem seems to be local to this client only. On the client I have made the following changes/observations. I have disabled the firewall, cleared the remote desktop cache, remove the MRU entries from the registry, verified that port 3389 is open via telnet. I have been bashing my head for days trying to figure out why this one box is not working. The problem occurs for every user on the box including the admin.I don't receive the box that prompts for warning if there is a server authentication issue but I think that is because I selected ignore at some point and said yes to continue. I'm not sure where that cache resides to delete that selection.
View 1 Replies View Relatedi would like to connect using RDC from my netbook (using windows 7 starter) to my desktop (using windows 7 professional) on the road.i have followed all the steps here: Allow Remote Desktop connections from outside your home network when i try to connect i get the dreaded "remote desktop can't connect to the remote computer" error message.
View 1 Replies View Relatedcan i connect to my server which more that 100 mts far away
View 1 Replies View RelatedI am trying to connect to another Windows 7 machine on the same router, but it will not connect. I have remote desktop enabled and checked under the computer settings, but when I right click the computer in the network & sharing center and try to connect, it won't work. I also tried manually entering the computer's network address but it failed. Both machines are Windows 7.
View 3 Replies View RelatedRemote Desktop Allowed
Regedit set to 3389
Norton 360 mstsc.exe allowed in traffic rules
ping to workstation replied
just can't get remote desktop to connect? any other things I should check?
Windows 7 (64-bit) will not connect to a remote location via VPN. I connect from my desktop running windows XP, but cannot connect on my Toshiba laptop running Windows 7.
View 2 Replies View RelatedJust recently immigrate to win 7, I used to connect my XP work computer via remote desktop from home, now I cant . The ping command works fine. How can I solve this problem?
View 9 Replies View Relatedi would like to connect using RDC from my netbook (using windows 7 starter) to my desktop (using windows 7 professional) on the road.
i have followed all the steps here: Allow Remote Desktop connections from outside your home network when i try to connect i get the dreaded "remote desktop can't connect to the remote computer" error message.
I have 3 computers with Windows 7 Pro.
I can use remote control between 2 of them, but I can not connect from any of those two to the third one. All the services needed for remote control are running, and I have tried several tutorials on how to set up remote control...and nothing. Again, only on third computer remote control does not work. On that computer I have 2 accounts: one standard and one admin. I have put admin account under "Select users" and did not help. Tried with enabled Administrator account and nothing. Below you will see the picture which describes the problem. I can not select who can connect.
Microsoft is gearing up to release a tool that will permit users of Windows Vista and Windows XP computers to connect to Windows 7 machines, and to take advantage of features that only the latest version of the Windows client brings to the table. Bridging Vista and XP with Windows 7 will be possible through the Remote Desktop Connection (RDC) 7.0 client.
The Redmond-based company has been cooking the client for some time now, and it appears that the baking time is almost over. There’s still no definitive delivery deadline, but with Windows 7 general availability now almost a month away, Remote Desktop Connection 7.0 GA is bound to follow.
I can't connect to the remote VPN. I did it successfully 1 week ago, when using XP. Verifying username and password stays too long and after that this error occurs. I've tried many things, but none of them worked. It is 100% sure that I enter the correct username, password and domain name.
Here is my dxdiag:
[Code] .....
I'm using Win7 Professional at home and winxp at my office. I can connect fine from home to office but can't connect from my office to home. I have gone through all of the google searchs and all of the posts on this forum without any luck. I have checked that my modem has port 3389 forwarded. I have confirmed that it's listening on that port. I have checked all the firewall settings, and even turned off the firewall and still can't connect.
View 6 Replies View Related
I want to do some things on my sisters' laptop which is in other country. Here is the situation:
My computer has Windows 7 Ultimate (64 bit) installed and I am using ADSL internet connection.
My sister lives far away in UK and her lap-top is connected to internet using the wireless. Window 7 ultimate is installed at her computer too.
Since I am complete beginner, please provide me step by step tutorial. I have tried a lot of tutorials that i have found on the web, but with no success.
We have 2 printers (one color, one b/w) in our office and 4 local computers.
The printers are connected by USB to one of the computers (a PC running XP) and they are shared on the local network. All of the 4 local computers can print to either printer with no problem.
The problem is that when I use remote desktop connection from one of the PCs (the only one that has Windows 7) I can only print to 1 of the 2 printers (the color).
When I use remote desktop connection from any of the other 3 computers then I have no problem printing to either printer.
I've tried speaking to the IT guys who run our offsite server and they have been no help (despite being expensive) so I'm trying to troubleshoot as much stuff on my end as possible to avoid spending a crazy amount on them. what I can check, or what other information I can provide to make diagnosing this problem easier?
Last night I was on the internet at home absolutely fine and my laptop automatically downloaded an update, since then I have been unable to connect to my wi-fi. I deleted the updates and was still unable to connect, so I tried to used a system recovery restore point and every one I use starts but fails to complete.So, I did a factory reset after around 8 hours of trying to sort it out today and I STILL have the same problem. I can plug in the cable to connect and my housemate is having absolutely no issues connecting and neither is my phone so now I am at a total loss what I should do to resolve this. Prior to the factory reset I was able to connect to the wi-fi but it was stating no network access/limited access and now it simply won't connect to my internet at all. It finds my full strength signal but will not connect.My drivers for the Broadcom 4313 802.11b/g/n card are the most up to date and the laptop (HP G62) says it is working fine.
View 2 Replies View RelatedIs there a way to unattended remote connect to a desktop, using existing MS tools, and share the desktop, without having to wait on the other user to give me a thumbs up?I work on a remote PC, and need the user there to be able to view the desktop while I work on it. However I also need them to also not have to directly give me access each time, such as the case with the help me request application (Windows Remote Assistance normal setup)
View 3 Replies View Relatedis it true the only Professional and Ultimate versions of Windows 7 can accept Remote Desktop Connection requests? I read on a post from 2009 that "any version of Windows 7 can act as a Remote Desktop client, but only Ultimate and Profession can host a Remote Desktop."I'm not sure I completely understand that - I do understand what host and client mean. However,d despite lots of different setting changes, I can't connect to this Windows machine using Remote Desktop.
View 1 Replies View RelatedI'm encountering a very frustrating problem connecting to my office PC (which is Windows 7 Professional). No matter what client I use (Windows 7 built in remote desktop from a W7HP machine, Remote Desktop Client on Android, etc.) when I log on to the host machine it re-logs me on. Basically it seems to kill the previous log on session, logs it off, and then logs me in anew. This is really annoying. It closes all open apps and makes me reopen them. It takes much longer than a usual connection. I can't seem to find any reason for why this might happen, the only difference between this and the thousands of connections I've made over the years using RDP is that this is being done over our work VPN (A SonicWall VPN client). I don't see why that would make any difference but it's the only variable.
View 1 Replies View RelatedI have setup Remote Desktop on two different Windows 7 computers and I am unable to connect to them. I have followed several examples, which are the same on setting this up, but still unable to connect. The examples show trying to connect using the computer name and user name. If you are connecting say from your office computer to your home computer, do you not have to enter the IP address somewhere or does it just connect via the computer name?
I have yet to find anywhere to enter an IP address or connect any way beside just using the computer name. I am setting this up to connect Windows 7 to Windows 7.
Here is what i would like to try and do. I have two computers, a Desktop and a Laptop. My Desktop sits at home, while my laptop goes with me to school or anywhere else that i need it.Now, i would like to see how i can set up my computers (or network?) so that i can access my Desktop files via my laptop online.I want to try and carry as few files on the laptop as possible, such as if ever lost or stolen, i wont have my data or files compromised/stolen.I also plan to install a SSD on the laptop, in order to try and make my battery last longer, but SSD's are still too expensive (i have a 250 HDD right now), I'm thinking of getting a 64GB SSD and trying to carry as few files as possible. Getting a 250 GB SSD is just way too expensive right now.I have heard that Windows has a thing called Remote Desktop Connection, but i have tried to use it, but i never got it to work somehow. I am running Windows 7 Home Premium.
View 2 Replies View RelatedJust wanted some advice on remote connecting to my machines on my LAN. I have a desktop running Win 7 Home, a laptop running Win 7 Pro and my media machine running Win 7 Home. I would really like to access my media machine running Win 7 Home remotely on my LAN from my desktop machine also running Win 7 Home and i wanted to use RDP as it seems straight forward for what i need. I understand that it does not work when trying to remote access from a Home Premium machine to another one which is a real pain! I was wondering as i have full access with RDP on my Laptop running Win 7 Pro could i perhaps copy all the RDP files from the Pro version to my Home Premium version to allow full access to RDP on both my Home Premium machines?
View 2 Replies View Relatedhow to Remote Desktop Connection connect to a Windows 7 standard account?All attempts to Remote Desktop Connection connect to a Win 7 standard account fail with:Attempts to the same account change to administrator succeed. But I cannot afford the risk of this account being administrator.The machine running RCD is Win XP, on the same switch.
View 3 Replies View RelatedI have a hosted Linux server running CentOS 5 with Samba 3.4. Everything is setup and it is accessible via Linux machines by typing [URL] in a Firefox address bar. I am trying to set up a local network share on a Windows 7 Home Premium x64 SP1 computer. I have tried entering the IP address in 2 locations:1. Map Network drive. I select a drive letter and type in the ip \12.345.678.9 It asks for credentials and I enter the user info for the user I created on the Linux machine. It thinks a moment then pops back up asking for credentials. It doesn't say they are invalid, just never goes through.2. Connect to a website (under Map Network Drive). I type the IP [URL] and click connect and it pops up a dialog saying "The folder you entered does not appear to be valid. Please choose another".
I have tried creating a loopback adapter and trying to setup a connection via SSH using the guide found at [URL]. After completing the tutorial (substituting my server IP address for the destination address given) I try using the Run dialog as indicated and get a "Windows cannot connect to.." error and the diagnose connection button. One thing that may be causing problems there is that the loopback adapter is labeled as an unidentified network and thus stuck as a public connection, and I am unable to change it. Searching for solutions to that brings up things I can't access (no group policy editor on Home Premium) or results in no change (setting DHCP server, which I tried setting to my router).
I can connect my local laptop to a remote desktop using Cisco Any Connect VPN on windows 7. I can use the internet, send emails, work with files on the remote computer.However if I switch back to the local laptop computer and use the internet, send emails, or open files the remote connection closesI get the folowing errorRemote Desktop Connection has stopped workingA problem caused the program to stop working correctly.
View 7 Replies View Relatedwhen i start making a connection using broadband 'error 711' occurs saying 'remote access connection manager could not start in time.
View 1 Replies View RelatedI want to shutdown other computer in our network so in CMD i type 'Net View'I see my other pc so i do 'Shutdown -i' i type pc name shutdown and then get access denied!
View 9 Replies View RelatedI want to remotely access to my office another PC which is working on win2000. I have administrator rights of that PC and trying to connect as remotely but none. Kindly give me procedure for access. I am using win seven.
View 1 Replies View RelatedI have an asministrator account on both computers with the same password. I have tried to shut it down with the command itself and the GUI. It always returns with the same error: "DESKTOP-PC: Access is denied.(5)". I have downloaded psshutdown, but I don't really know how to use it.
View 9 Replies View RelatedI want to use registry remote to edit registry of another computer in my network,But I can't access HKEY_LOCAL_MACHINE(It's say I have no permission )I use administrator (built_in) user,But i can't change permission by registry remote
View 1 Replies View Related