I was able to set up win 7 on raid 0 before. Now I am trying to do a fresh install of win 7 again. Everything seems to be ok but when I get to "where do you want to install windows" menu I get a similar error message.
I tried to delete the partition and load the raid driver from asus. Also tried to split the drive. But still gets this same message. Bios is set up for raid. And I am installing win 7 from a usb drive
I'm getting this error when trying to install windows 7 rc x64:
"Setup couldn't create new system partition"
Then it asks me to check the setup log, but I don't know how.
Trying to install onto the 2nd partition of a 160 gb drive, split in half. It's disk 0, the first partition is active primary and has XP. The second partition is formatted ntfs primary and when I select it in windows setup, that's when I get the error message. I let windows 7 delete it and create a new partition and formatted it, but when I select it to install windows onto, it give me the above message.
It's a SATA drive running in native IDE mode on an AMD790GX board with a Phenom II X4 940 and 4 GB RAM.
It doesn't seem like it would be a drivers issues, since Windows sees the drive and both partitions, allows me to delete, create and format partitions, just won't let me install onto it. Any ideas?
Is giving the following error when trying to install windows 7 in HD:
"setup was unable to create a new system partition or locate an existing system partition"
I've tried to do some procedures, but also can not create partition, do not know what else to do.
I built a new pc and i want to put windows 7 pro on it. When i try to install i got the message "setup unable to create a new system partition or locate an existing one". How do I fix this?
View 9 Replies View RelatedThis is a fresh Windows 7 install on a 500GB HDD (previously used under XP) In the BIOS the Storage is configured as: Raid. Obviously I have the right raid ICH10R drivers from Asus (they are on a USB drive) Installation starts, Windows sees the disk, I specify the drivers, BUT when I click Next, I get: Setup was unable to create a new system partition. I can delete the partition, create a new one, format it, BUT when I click Next, I get: Setup was unable to create a new system partition. I used Gparted to delete the partition, and tried again - I used Seagate tools to zero the disk (sort of low level format) - If I try to install on a brand new 1TB HDD following the same steps, it installs fine... Both drives are Sata II and I used the same Sata port (only one disk at a time)
View 2 Replies View RelatedClean install of windows 7 on 2 160gb sata HDD's set up for a raid 0
when i select a partition to install the OS onto it gives me the error
"Setup was unable to create a new system partition or locate an existing system partition. see the Setup log files for more information."
any suggestions?
Yesterday i want to install windows 7 on my laptop but when i format Local disk C and click next it says setup was unable to create a new system partition.I boot through Pen Drive. I dont have a dvd rw(not working) and i have Data on other drives[/COLOR]...without wiping data and with wiping data.
View 9 Replies View RelatedSo i'm trying to do a clean install on windows 7, i've tried to format and then do the install but it still says setup was unable to create a new system partition
View 14 Replies View RelatedWhen I try and install Windows 7 64-bit on my hard drives I get the fallowing error.
Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information.
Its doing this with vista now.
After 8 long years I've finally upgraded my wheezy old pc, and now am drooling to play with this beastly new machine I've just assembled. My system specs should be in my sig below.But after 12 long hours of trying to install windows 7 pro, I'm more kinds of frustrated than there are words for.As in the topic title, I'm up against the "setup cannot find or create a system partition" error. My machine has a single 2 TB Hitachi Sata 3 hard drive, so there is no raid to muck things up, which seems to have been the primary cause of everyone elses troubles with this error. Using my old rig, I partitioned the new drive and transferred all the data from the old drives, leaving the first 75 GB partition empty and waiting for windows 7.
Then "the troubles" began. Research ensued.First thing I tried was to load updated sata 3 drivers from the mobo install disk. No help.Then I tried downloading the latest drivers from Asus and loading them from a flash drive during installation. No dice.Then I tried changing bios settings from Sata to IDE. No dice.Tried all of the above again with minor tweaks. Using the setup tools, I deleted that first partition and tried to make it again but setup gives me the title error.Well, of course I need that partition back so after some more research, I downloaded gparted, booted it up, but the video output is messed up and impossible to read.Then I slept for 6 hours. I woke up, tenacious and desperate, and figured I'd try diskpart (well above my paygrade) to make the first partition active and/or primary. Diskpart won't allow it? I disassembled my new system, plonked the old system back into the case, booted up into winxp off the old hard drive and with Easus partition manager and tried the same thing as with diskpart, but with the same results. No dice.Then, clearly somewhat crazy at this point, I put the new machine back in the case and tried ALL OF THE ABOVE AGAIN. No dice.Upon boot, POST sees the hard drive, but its not detected in bios. I don't know whether this is a hard drive problem, a mobo problem, a configuration problem, or completely normal for my gear. In any case, windows setup lists all the partitions.
I am having a problem with doing a fresh install of Windows 7. It is on a Dell Inspiron 1546 with a 150 GB hard drive. There was an original install but the computer was having issues as some files were corrupted. I used the Windows 7 disc to format the hard drive and booted from CD after restarting.
However when I try to install the new Windows 7 it sits at the part where it says: Expanding files. Then after a while an error pops up that says: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information
I have my HP Laptop which came with Windows Vista as the OS. I want to upgrade to Windows 7 so I bought Windows 7 from my local store.I entered the disc and did boot from CD. It reached to the page where it shows the disk partition. I deleted the partitions and created new one. However, whenever I create the partition, it creates a primary one and gives me saying Setup was unable to create a new system partition or locate an existing system partition.The stupidity that I did was deleted the partition which had the Recovery Drive in it. So, now I am stuck and not able to install Vista as well as Windows 7. I am not able to boot Windows as there is no OS in my laptop now.
View 9 Replies View RelatedSo I used to have vista, xp, and mac on my pc. After a while xp screwed up and left me with only vista and mac. My school handed out a bunch of software including windows 7. I saved the installer and key on my desktop and pretty much just left it there for two months. Eventually my vista crashed and could have only used mac. After a very short while my mac crashed to. I saved my key on a piece of paper but unfortunately I lost the installer.
This morning I found a iso, burnt it on another computer and popped it in. Everything was fine until I was asked where I want windows to be installed. Due to the fact that I tried to fix vista from dos, my hard drive configuration got messed up. Regardless of that I didn't care because everything was backed up on a external so I tried to format all of my hard drives and then instal windows. "Setup was unable to create a new system partition or locate an existing system partition." What am I supposed to do?
I have my HP Laptop which came with Windows Vista as the OS. I want to upgrade to Windows 7 so I bought Windows 7 from my local store.I entered the disc and did boot from CD. It reached to the page where it shows the disk partition. I deleted the partitions and created new one. However, whenever I create the partition, it creates a primary one and gives me error saying Setup was unable to create a new system partition or locate an existing system partition.
View 9 Replies View RelatedI have made a reformat on my hdd to install Win 7. But during install this message comes" Setup was unable to create a new system partiton or locate an exsisting system partiton" And if I start my computer without a DVD this message comes in the end "BOOTMGR IS MISSING"
View 1 Replies View RelatedRecently my SSD failed so I tried installing windows 7 from DVD on my HDD but I always get an error message: "Setup was unable to create a new system partition or locate an existing system partition."I've tried everything I could find here: I gave boot priority to the HDD, I unplugged every other device but nothing seems to work.
View 4 Replies View RelatedLast night after 8 hours of toil, I finally completed a clean install using a usb drive on my asus ux32vd using the brand new SSD drive I had just bought. The reason it took so long was I kept getting this error -> "Setup was unable to create a new system partition or locate an existing system partition." What I did to finally get it to install was get to the c prompt during the installation and run diskpart and make the integrated 32GB SSD 'offline' and then I selected the SSD and used the 'clean' command and left the SSD unpartitioned and raw. I had read that with SSDs on a clean install you should leave it raw and windows will install on it. And it worked. Now here's problem number 2, which feels worse than problem number 1. After installing everything went swimmingly. I started updating drivers, etc. I got to the point where I needed to do a Windows Update. There were 91 things that needed to be updated/installed. So I ran update with all 91 and that went fine until it went to restart - it wouldn't boot into windows. Instead it kept going into that startup restoration program over and over saying it couldn't fix the problem. I tried to delete the updates manually through cprompt by running dism, but this failed and I figured to hell with the hassle I'll just reinstall Windows since I know how now and then update windows one update at a time. BIG MISTAKE. I tried doing EXACTLY what I had done before - doing diskpart, offlining the integrated SSD, etc - however this time the error isn't going away. It's still saying "Setup was unable to create a new system partition or locate an existing system partition." I don't get it. I'm doing exactly what I did when I got it to work, but it's not working now. I can only surmise that the system is still recognizing the integrated SSD somehow.
View 9 Replies View RelatedA friend has asked me to install Widows 7 on a friends laptop which has XP. The laptop doesn't have a DVD drive (no drive at all) so I've had to stick the installer on a USB stick from disc using a program.The USB boots up fine on the laptop, just like a disc. I formatted 2 partitions (same drive) and tried to install windows 7 but I get this error:"setup was unable to create a new system partition or locate an existing partition"So now, I have someone else's laptop with no OS. The owner is a 70 year old computer illiterate man.i'm planning on trying to install Vista instead and if successful, upgrade to 7. I would have upgraded in the 1st place, but P can't be directly upgraded to 7.
View 6 Replies View RelatedI am unable to install windows 7 as , when I start the install and click on install it shows that setup was unable to create a new partition or locate an existing system partition.I have 2 hard disks , one of size 75 gb & other of 320 Gb..Previously , OS was installed on 320 gb , but i have formatted that drive before installing windows 7...
now my 75 gb hard disk is empty & one drive of 320 gb is also empty..It shows that 320 gb hdd ia on disk 0 & 75 gb on disk 1.I want to install Os in any of the above mentioned HDD.It shows that-> 1. all drives of 320 gb HDD as Logical & 75 gb HDD drives as Primary..
I need to create a custom/unattendable setup for Windows 7 Professional for my new laptop that I will be purchasing soon I will also need to install certain Windows Componants along with other customisations.My current laptop is running Windows XP Pro SP3 and i'm looking for a piece of software that will enable me to complete the setup tweak.I have donwloadedand installed vLite[URL]on my XP machine but it has asked me to download the WIN AIK(Automated Installtion Kit) from the Microsoft Website. This is only combatable for Windows Vista andServer 2008 and is 1.3GB in size.
View 2 Replies View RelatedI tried to dual boot Fedora 18 with my Windows 7. They are on two different hard drives. Fedora 18 worked but I was unable to boot up Windows 7. Frustrated, I decided to just delete everything from all the hard drives and try to do a clean install of Windows 7 using the USB-DVD Windows tool to make a USB Windows 7 installer. I then got the following error when trying to install Windows onto my hard drive:
"Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information"
I tried unplugging the other hard drives and got the same error. I also went to the command prompt and used Diskpart and did clean all. Still the error shows up. Something that might be useful is that when I did disk list in the command prompt it showed my hard drive but with 0 free space. Not sure if this is useful but the drive I want Windows 7 on is a solid state drive but the one I had Fedora on is a normal hard drive and I had an extra harddrive that I used for storage that is a normal hard drive as well.
while installing windows 7 from the installation DVD, everything works fine till the screen where it asks me to select the partition on which i would like to install Windows. When I select Partition 4 and click Next it gives me an error saying "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have only one HDD and no external USB's or drives attached to my CPU.
View 5 Replies View Relatedhow to go one step further and create a desktop shortcut (or hotkey) to the speaker setup page where you choose your audio channels? (ie/ where you choose between Stereo, 5.1 Surround, 7.1 Surround, etc.) It's one click after getting to the Playback page. After getting to the Playback page, you'd click "Configure" to get there. It's this page here:
I need to switch quickly between "Stereo" and "5.1 Surround" and I'd like to get here with a single click (or hotkey). Does anyone know?
I want to have a Factory Reset of my computer. In order to launch a System Recovery, I need to create Restore Discs. When I launch the Recovery Disc Creation, it says:"This computer does not have a burning drive, which is required to make DVDs. Please contact HP Support for asistance."My computer did not come with a build in CD Drive. Even plugging in a USB CD Drive will not make creating the discs possible. So. I ask you. How can I reset my computer to Factory Condition?
Computer Specs:
Windows 7 Home Premium (64-Bit)
Model: HP Pavillion dm3 Notebook PC
edit: This notebook came with a Recovery Partition built in.
How to Automatically Create A System Restore Point at Startup ?
View 0 Replies View RelatedI'm doing a fresh install on windows 7, instead of a disk it's on a thumb drive
I have a 500 GB Partition I want to install windows toI went through setup and formatted the disk when I try to continue with the installation and get this error.
I have a Windows 7 Home Premium 32-bit with SP1 (OEM). I have already installed the Windows and activated online. Also i have installed all my motherboards drivers such as audio, lan, raid and gpu.The whole process took me around 1 hour 30 mins.Next month i'm planning to format my hdd and clean my pc (cleaning the dust from the fans, cpu).I do that every month.In the future i don't want to install Windows all over again (by installing it from a disc) it takes too long for my liking. Also with my OEM version of Windows i think you're only allowed 3 times activation by going online, then after that you have to call up Microsoft which is a hassle.What i want:
* I want to create a full system image of my whole hdd/windows/pc
* After a month or so i insert a disc or from another hdd and copy the entire image to a new hdd or a formatted hdd and have all my previous windows all installed with activated and with all drivers.
I have a 1TB drive that partitioned with 120gb system and rest is a non primary/non boot data partition volume... I've never used windows 7 create system image, but want to. When I try to create a system image it insist on backing up both drives. I don't see how to deselect the data drive. Is this because I have installed something system related. on the data drive? And Finally, how will recovery of a system image works if I get a blue screen, do I need to install windows 7 again first or have a repair CD? I noticed when I started a create system image it asked me for the destination drive, no exact path on the drive, does the image have be created on the root of the destination drive?
View 1 Replies View RelatedI have been trying to install windows 7 on my hd and initially started with ubuntu on partition 1 then resized partition to leave unallocated space for windows 7.Now I am installing windows 7 from cd and can't get past 'where do you want to install Windows' page because of error stated in title.I've tried having unallocated space, a ntfs partition, and now have completely wiped the hd of ubuntu's partitions to clean install windows 7. None of the attempts have gotten me past the location of install page.
View 4 Replies View Relatedpreviously i have windows xp on my lappy. then i removed it and installed windows 7. but it wasnt restart. then with the help of windows recovery somehow i restared. but some of the drivers are not installing, and showing that system doesnot meet minimum requirments. then i tryed to find the problem. i observed that system reserved partition was not created. so i reinstalled windows.
View 3 Replies View RelatedI am building a new system for a friend. I was wondering how do I enable the setup screen for a first time user after I have installed the OS and updated all the drivers and windows updates? Like how do I make it so that when I give him the system and he turns it on for the first time it'll ask him all the setup info like when you start a new computer for the first time.
View 3 Replies View Related