My system crashed on bootup. I was booting off my RAID. All 3 disks say error. When I try to install Windows 7 and repair it won't let me load the nvidia drivers. The nvidia drivers are .exe installations. Does any know where I can download the normal nvidia drivers to install?
View 1 RepliesCan't access any files. Need it urgently as it has all my uni stuff and need it to submit before deadline.
View 9 Replies View RelatedI have an HTPC that I've had for about 4 years now. Today when I booted it up it went into an infinite loop with the 'Startup Repair Utility" where it would just sit there claiming to be repairing the drive but never actually completing or providing a notification of the issues (typical Microsoft troubleshooting). Anyway, I finally was able to get into the advanced settings of the utility and get to a command prompt and see what was going on.
1)The previous RAID 1 configuration was setup as the main C: drive with the OS and also where I had all our music stored. But now during the boot sequence the bios startup it flashes in red complaining about the RAID array having degraded and when I finally got into a command prompt it was no longer mapped to C:, the two drives in the array were mapping independently as drive E: and F: respectively (the DVD-ROM is the D: drive).
2)My first concern was to get my music off it so I plugged in an external USB drive and went into command prompt and tried to xcopy from E:, it started to copy then failed catastrophically with a weird error so that would appear to be the bad drive. I then tried the same thing on drive F: (the mirror) and its cranking along nicely copying all my music over. My fingers are crossed but I suspect I'll be OK, its unlikely to get two drive failures in the same array at the exact same time
Once I get my data off the good drive how should I proceed? I assume I need to get a new duplicate drive installed and then can I not rebuild the RAID array from the good drive? I've never done this before, the machine came built for me so I'm not familiar how it is setup. What I do know is that it has a 'RAID utility' you can jump into at boot up by hitting F10.
Setup 4 disks on a windows 7 PRO unit using the disk manager raid utility. Created a JBOD. On re-boot, all drives are reflecting a failed message.
View 1 Replies View RelatedMy system is configured with a SSD drive for my Windows 7 x64 Partition (C:) and I setup two 500 GB drives in a RAID 0 config (Z:) to host only game installations. One of the hard drives suffered a heart attack (I can only assume as there was no warning signs) therefore wiping out my games partition (all my saves are backed up to a remote location). Now, I'm trying to re-do my raid setup with a new drive, but when I try installing Steam (it's an .MSI file), it tells me that: "Error 1327.nvalid Drive Z:" and crashes prematurely without any option to specify another point of installation, the same happens when I try to uninstall via "Programs and Features" in the Control Panel. Now, I have quite a few games that are still showing up, and I get the error "Ble bla blah no longer exists or
View 1 Replies View RelatedI went to boot up my laptop PC and I see H20Insyde asking me for a password. I have no idea where this came from. What could have caused this? I have always booted up and the only thing I see is my normal screen from Windows 7 that ask for my password.
View 1 Replies View RelatedInstalled a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies View RelatedI have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
I have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
View 1 Replies View RelatedI need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies View RelatedI had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
View 4 Replies View RelatedWhich configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
View 1 Replies View Relatedanyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
i have a spare pc a medion core duo it has win 7 as an upgrade and never had any problems, when it boots up now it starts a repair, after that it works ok, i have done a check on the hard drive etc but i cant find anything wrong? is there a test i can do to find out why it does a repair?
Running TSG SysInfo would be useless, because I am having to make the inquiry from an entirely different computer.The computer in question, however, is a Dell Inspiron desktop, running Windows 7. Five or six months ago, in setting my then-new Dell computer I evidently responded to a prompt by creating a bootup password, with an accompanying Hint. But through those months the computer never asked for the password, <b>until two days ago</b>. It prompted me with "wherehus", (the "hus" being "husband", referring to me) which I believe to be a truncated version of the hint I set up originally. It now suddenly wants the password. and why that change and why the hint is truncated, I have no idea. I apparently never wrote down what the password should be, like a natural-born fool.That hint had to continue with something like BORN, EDUCATED, SERVED IN ARMY, MARRIED, and the like. "BORN" could be Rochester, or Rochester Minnesota, or St. Mary's or St.Mary's Hospital or something like that. If it was "ARMY", the password would surely be Germany. And so on with names of grade and high school, university, or private business school, many of them having several possible "answers", as above. And maybe some other "wheres" that I can't think of. Of course any of those would be subject to capitalization, spacing, and/or punctuation. A password wilderness.I've worked over those possibilities exhaustively, and haven't struck the real password. I've more or less run dry with variations.That's not a technical problem that anyone could help with remotely, so I have to assume I am not going to come up with the password. And therein lies my present dilemma. I'm not asking for instructions in hacking the password back, as I know you won't do that. The computer came with Windows 7 installed, and I do have a brand-new, never-used, Windows 7 installation set, which I bought for a different computer but haven't installed because that computer doesn't have enough memory or hard drive space. Which leads me to a number of puzzlements:
1. Older versions of Windows, when installed, wiped out EVERYTHING on the hard drive, or at least left them irretrievable. I think I have heard that Windows 7 does not do that. Does anyone know?
If forced to it, I could live with a wiped-clean hard drive if that's what the new installation would do. I have or can get installation disks for the software, and recreating or retrieving the data from backups would be possible, though a pain in the neck.
2. But is it even going to be possible to install the new Windows 7, with or without the hard drive contents? Since I can't boot up, how can I run the Windows 7 installation CD(s)?
3. Where, if anyone knows, is the password stored? If it's in some semipermanent memory in the computer rather than on the hard disk, might I be stuck with that unknown password even after a new Windows 7 install?
4. Or even if I installed a different new hard drive and managed to install Windows 7, would I still be stuck?
My computer crashed several months ago. I have 2 hard drives so I reinstalled windows 7 on my D drive. I also reverted back to an earlier version of the OS which corrected the problem on the C drive. How can I remove the OS from the D drive now that I don't need it. Whenever I boot up it asked me which OS I want to use. I actually reformatted the D drive but it is still asking me which OS I want to use. How do I correct this problem so it only sees the OS on the C drive. I couldnt find anything in the Bios to correct it. I have a Dell Inspiron 570.
View 3 Replies View Related7-ultimate I want to know if it is possible to make Windows 7 NOT use the free unused RAM as whatever the storage it is using for, as seen in the other thread? Like I don't want it to occupy 1GB of RAM
View 2 Replies View RelatedI bought a new pc from aria.co.uk, it came in good nic and works fine. I booted up the pc, noticing a very strange lack of any motherboard logos or bios buttons, and proceeded to insatll windows 7. I chose the 64 bit version, I got to the part where it says it is going to restart windows in 5,4,3 etc. It restarted, only for the windows installation to start back at the very first setup screen. I looked at the partitions in custom install and it said that both partitions had installed correctly, my problem was getting to the oncluding install option. I shut down the pc, and took out the windows disc and restarted it. Again no bios options, just a black screen saying "loading operating system" and then "windows did not start correctly" , it took about 20 seconds for the screen to change and then immediately restarted itself taking another 20 seconds? It loaded the windows files and I was releived to get to the final setup screen. After finishing the installation it told me it was going to restart windows, which it did, only for it to reset itself about 3 times, again saying "loading operating system"..... I had a play around with pc, altering the resoluton and stuff, and shut it down for about 5 minutes. When I turned it on it told me "windows did not start correctly" and took me system repair, in which it found a problem and couldn't fix it. The hardware was fine, but it said "a patch stopped the system from starting". It is very hit and miss and sometimes starts normally and sometimes takes me directly into system repair. I managed to get into the bios once by pressing delete rapidly at boot up, and hardrive was selected as priority, so that couldn't be the problem involving windows.
View 1 Replies View RelatedI am having a bit of an odd issue with my Alienware MX11 laptop. I just restored it to a previous "checkpoint" after just having the error "Failed to save all the components for the file \System32\000052af. This file is corrupted or unreadable This error may be cause by a PC hardware problem." After restoring via Control Panel it is running generally fine. However, my issue is wanting to reset it to factory default settings. I've reset to the Factory Image before with previous Dell laptops, but for some reason the repair menu will not load past the black screen with the grey bar on the bottom with the words "Windows is loading files..." After the bar fills white (very quickly might I add) it returns to being gray and sits there.
Is there another way to return to factory image or a way to fix this?
This laptop is still fairly young (got it last month) and the warrenty is still good.
Windows gives me a yahoo home at boot. I want the windows homepage at boot up.
View 1 Replies View RelatedMy IT shop recently rolled out several hundred new Dells with Windows 7. We've had minimal problems so far.
However, our HR and legal folks are bugging us to change the format of the LegalNotice screen at Win7 startup. All PCs are connected to shared network resources and they insist on the LegalNotice being activated, with an "appropriate use" message displayed and a click-through acknowledgement by the user.
In Win XP, this notice was displayed in a separate dialog box, with the message in a simple black-on-white textbox.
In Win7, the notice now comes up in the center of a blue graphic background, and is in a bluish font that is both smaller (in high screen resolutions, especially) and a harder-to-read typeface, which makes the notice virtually useless.
LegalNotice is controlled by a couple registry settings, but they only allow you to activate it, set the box caption, and set the box text. No other format control is available, e.g., font type, size, weight, textbox background/transparency, etc.
One thought we had was to imbed the notice in the background graphic, but that raised problems with centering and placement due to differing monitor resolution settings. Plus we haven't quite figured out how to replace the default graphic.
I have a strange issue with my PC, I keep getting BSOD whenever I power my PC on. It BSOD's a few minutes after booting Windows or sometimes half way through loading with different error messages and usually repeats the same process about 3 times, after that all is fine. The PC will not crash at all, and would be on for hours on end, either idling, playing media/gaming/browsing etc. BSOD Error messages are often; driver not equal or less etc, USB Bug code, non page area etc.I have attached a few days worth of Minidumps that have been created (most recent).Please note, iv'e tested my memory (which most always suggest) and Memtest found no faults on a full test. And I know for sure it cannot be that otherwise it would crash whilst doing something that requires much more memory use.Iv'e took every USB's out of the ports and the problem is still there.It must be a corrupt driver of some kind or a problem with bootup/system files?
Specs:
Processor: Intel Core 2 Quad Q6700 @ 2.66GHz
Memory: 2x2GB DDR2 Samsung 800Mhz Dual Channel Ram
Hard Drive: 640GB + 500GB + 300GB Sata II & 300GB IDE
Video Card:XFX ATI Radeon HD5770 1GB GDDR5 DX11 Single Slot
Monitor: BenQ G2220HDA 1080p 1920x1080 (16:9)
Sound Card: TerraTec Aureon 5.1 Fun Card (2.1 PC + 5.1 Optical out)
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) SP1
Motherboard: Acer MCP73PV MicroATX Motherboard
PSU: OCZ 600W MODXSTREAM PRO PSU
I have had multiple instances now where Windows 7 hung after I started up and logged into an account. It seems to happen when I try to start a program by double-clicking on it. For example, it has hung when I tried to start CCleaner or Firefox. When I get into this state, Ctrl-Alt-Del does nothing. In some cases, I can right-click on the Taskbar and choose "Task Manager," but it won't run (I just get the hourglass cursor). Today I tried to start Firefox and nothing happened, and the hourglass cursor shows in the Taskbar, so I can't even see the menu for the Task Manager.
This is happening on a Toshiba laptop running Windows 7 Home Premium 64-bit. It seems to occur when I don't wait long enough for the login to finish. When it happens, the only way out is to hold down the power key until it shuts off the system. Of course Windows is too stupid to tell me when it is done loading stuff into memory and starting its services; why can't they simply tell me when the login process is done and the system is ready to use? I find it infuriating that a supposedly multi-threaded, multi-tasking operating system can be so flaky. But enough of my rant; on to the possible cause:
I strongly suspect that my problems may be caused by SpySweeper, since it seems to be the last program that loads at login. (Or at least it's the last one to put up an annoying splash screen.) I use the following programs on my machine:
Windows Defender
Avast! Antivirus
Malwarebytes Anti-Malware
SuperAntiSpyware
Spybot Search & Destroy
SpySweeper
I have read that SpySweeper sometimes conflicts with other programs, so I turned off real-time protection for Windows Defender. I have read conflicting opinions on whether SpySweeper conflicts with Spybot's TeaTimer program. Do I need to somehow turn off TeaTimer too?
Even if SpySweeper is the cause of my problems, I find it very disturbing that misbehaving or even deadlocked application programs should be able to prevent the Task Manager from running.
Can't get into windows, black screen with blinking cursor for some reason I can't even get into windows 7, after I get pass the screen that says "asus", my laptop brand, It goes into a black screen with a blinking cursor in the left hand corner like this: Click this bar to view the full image. I'm unable to do anything at that point, it just blinks. I can't even boot into safe mode now, the only think I'm able to get into is the Bios Setup Utility menus and Asus' express gate, which is just a media/internet/gaming/skype thing that doesn't allow .exe files to run. This came factory installed so I don't have a windows 7 disc to run fixes.
View 6 Replies View RelatedI need to install either windows XP or windows 7 on my USB stick so I can boot my computer from the USB and use it like a normal installation. Articles I read tell you how to install Windows on a USB but not how to allow your computer to boot from the USB like it would be a HDD. I know how to set up my BIOS and I don't need an explanation in that respect I just need a step by step guide or at least a good guide on how to install either XP or 7 onto a USB, not from I've done that 1,000,000 times.
View 9 Replies View RelatedI'm having trouble installing windows on a new rig I just built. I'm not sure if its a driver error or maybe some other hardware error I'm overlooking. Here's the problem I'm encountering. I've tried to install 3 different windows. Windows 7 64bit(burned), Windows 7 32bit (burned), Windows Vista OEM. Upon the fresh install my computer goes to the "Loading files from disk" than will try to boot up to the install. When the boot up screen comes on with the horizontal bar it freezes after about 10-15 seconds, then nothing.I have 3 hard drives I've tried to install every copy on (2 SATA HDDs, and a SSD). Same symptom. My old HDD with windows still on it, I tried to boot it up and it still freezes(shouldn't boot up anyway right?). When I try to load safemode on the HDD with windows on it, I am able to. I tried installing the Vista copy through this method and it is successful until the PC reboots during the install and freezes back up bootup. This made me think it was a driver error.
I also mistakenly tried installing windows with no HDD's attached to the motherboard.. That also made it to the bootup screen, but froze(duh) at the bootup screen too. So from that mistaken test, could this be a hardware issue if its freezing at the same spot with and without the HDD? [code]I've also tried removing the video card and using the onboard video, leaving only one stick of ram in, and I've swapped ram from another PC to test(can't remember the model ram). I haven't tried swapping the dvd drive yet. I've read places that a heatsink could be causing this problem, but if I can get into safe mode on an old windows install could it be hardware such as the heatsink/cpu, or just drivers?
I keep getting BSOD whenever I power my PC on. It BSOD's a few minutes after booting Windows or sometimes half way through loading with different error messages and usually repeats the same process about 3 times, after that all is fine. The PC will not crash at all, and would be on for hours on end, either idling, playing media/gaming/browsing etc. BSOD Error messages are often; driver not equal or less etc, USB Bug code, non page area etc.I have attached a few days worth of Minidumps that have been created (most recent). [URL] iv'e tested my memory (which most always suggest) and Memtest found no faults on a full test. And I know for sure it cannot be that otherwise it would crash whilst doing something that requires much more memory use.
Specs:
Quote :Processor: Intel Core 2 Quad Q6700 @ 2.66GHz
Memory: 2x2GB DDR2 Samsung 800Mhz Dual Channel Ram
Hard Drive: 640GB + 500GB + 300GB Sata II & 300GB IDE
Video Card:XFX ATI Radeon HD5770 1GB GDDR5 DX11 Single Slot
Monitor: BenQ G2220HDA 1080p 1920x1080 (16:9)
Sound Card: TerraTec Aureon 5.1 Fun Card (2.1 PC + 5.1 Optical out)
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) SP1
Motherboard: Acer MCP73PV MicroATX Motherboard
PSU: OCZ 600W MODXSTREAM PRO PSU
At the screen where the Windows 7 logo is, my startup freezes and then many different coloured pixels appear at the top of the screen.This happens when trying to boot into safe mode as well
View 1 Replies View Relatedspecs are im getting all this info right off the system info)
Processor: Intel(R) Pentium(R) Dual CPU E2180 @ 2.00 GHZ 2.00GHz
Installed memory(RAM): 3.00GB
Sytem type: 64-bit operating system
Hard drive - 80GB
Motherboard: Desktop board media series intel DG33TL
I just clean installed windows 7 ultimate 64-bit i have tried 32 bit as well but i have had no difference in booting up i did not install anything yet as the boot up is very slow i have tried different hard-drive as well i have 2 80 GB hard drives one is maxtor and one is WD both are IDE...i disconnected everything extra that i had on my comp like Nvidia Geforce GTX 460 video CARD using on board video card i had a wireless card installed took that ooff as well took off the extra fans i had. Previously i had windows xp installed and it working very smooth so i have no clue what can it be as there is no virus before i installed it i had cleaned it up and installed it clean.
At present I have my WIN 7 set to Boot up without a Password. I would now like to change that siuation back to a "Password Required" Boot.
I have tried going into User Accounts >Change Passwords where I get the three boxes "Current Password", "Change Password" and "Confirm New Password" all blank as expected.
Its what happens next that has me puzzled. I tried leaving the "Current Password" blank , entered a new Password into the "Change Password" box and re-entered this into the last Box .
I now get the message " The password you typed is incorrect. Please re-type your new Password"
Since a Windows update at 3 AM this morning Windows Explorer keeps freezing and i can't do anything beside a reboot using the power button of my computer. It seems to be random. It mostly happens when i open a file or a folder, right click on something or do anything involving explorer.I tried to do a system restore but didn't fix it. I'm wrting this in safe mode and so far i have no problem.
View 5 Replies View Related