USG Device Not Recognized Error When HTC Inspire Phone Plugged

Jun 24, 2012

get my Windows 7 64 bit PC to reconize my HTC Inspire cell phone. What happens is when I plu it in to any USB port I get an pop up error "USG Device Not Recognized" and looking at my device manager/Serial Bus Controllers it says "Unknown Device". I uninstalled every controller and restarted PC and they re installed and still get the same error. I installed the HTC driver from their web site and still same error. Whats odd it doesn't work on this PC but works on my other laptop.

View 4 Replies


ADVERTISEMENT

Usb Device Not Recognized Error

Jun 26, 2011

I have a laser projector, and i control it with my windows seven notebook by usb.
Problem is, sometimes by a static shock of other devices or by other causes i do not know of, the notebook suddenly refuses to work with the usb drive anymore and the projector freezes.

but here is the part i want to solve. after replugging the usb drive windows says that the usb device is not regonised.... after plugging out and waiting 2 minutes and then replug makes it work again...if i do it sooner then usally it still shits about the device not being regonised.

View 9 Replies View Related

USB Device Not Recognized Error

Jan 11, 2013

USB Device not Recognized::error while connecting my external hard disk,previously it was working fine

View 2 Replies View Related

Cannot Get Rid Of (USB Device Not Recognized) Error Message

Jan 31, 2012

Whenever I use one of my USB ports, afterwards I get an error that lasts all the time that says USB device not recognized. I have gotten rid of it but then when I go back and use it again, that error pops up. The usb ports work, I use it to download pictures and other things, but I cannot get the error gone. Someone suggested I unplug the internet completely for a few minutes and it would reset itself, but that didn't work. I put the media card usb back into the port and went to where it says it is safe to remove hardware and then took it out, but that didn't work either.

View 9 Replies View Related

Hardisk Is Plugged But Not Being Recognized?

May 17, 2012

how do i get mt hardisk to start working

View 1 Replies View Related

Usb Pci Card - Devices Plugged Into It Not Recognized

Sep 9, 2009

I just installed a new PCI USB 2.0 card into my machine. I have a Line 6 Toneport UX8 that connects to the PC by USB as the interface for microphones and instruments. Because of the high volume of data coming down the pipe from this external interface it is pretty much a 'mandatory recommendation' to use a dedicated USB controller in a PCI slot.

Anyway, I installed the PCI card just fine but when I plug in the UX8 to it, Windows 7 reports 'USB device not recognized'. It is recognized if I plug it into one of the motherboard's USB slots though. I need to use this PCI card, otherwise the recording quality is useless. I know other people have this external interface and run it into a dedicated PCI/USB controller with great results. So I am hoping someone here can suggest what I can do to get Windows 7 to recognize the card and the USB devices plugged into it.

I'm hoping I don't have to reinstall the OS since it will be a pain to have to reinstall again when the commercial licenses come out in less than a month (I'm assuming I'll have to reinstall since I will be using an upgrade from my XP Pro that I have not used since trying out this Windows 7 RC).

View 7 Replies View Related

Unknown Device (Code 43) HTC Phone Connected To Computer Via USB

Nov 7, 2012

Since about 1-2 months ago whenever I hooked up my phone (HTC Rezound) to my computer through my USB chord I get an error message saying that it's an unrecognized device and that it was stopped because the device has shown previous problems. I used to upload videos and pictures from my phone to my computer about once a week for months straight and I didn't have a problem with it. Is there any way that I can adjust something in my computer to fix this?

View 1 Replies View Related

BSOD When Plugged In Usb Device?

Sep 18, 2012

including mouse, adapter, pendrive..

View 7 Replies View Related

Bluetooth Device Not Plugged In

Jun 7, 2011

my bluetooth device not plug in..why?and always show me message no bluetooth device

View 1 Replies View Related

System Interrupts High CPU When Any Usb Device Gets Plugged In

Nov 22, 2012

Whenever a USB device is plugged into my laptop (any of the USB ports), the CPU usage goes way up. It stays up even when the device is then unplugged, and the only way to bring it back down is to either reboot, or to go into "sleep" (when Windows resumes the problem is gone).

The Windows 7 resource monitor indicates that the problem is System Interrupts - Deferred Procedure Calls and Interrupt Service Routines. I have updated my drivers for each thing, and that has not helped. Not has lots of Google searches on this problem.

Running Windows 7 Home Professional 64 bit, on a Toshiba Portege R705-P41.

View 7 Replies View Related

Windows 7 Computer Won't Find New USB Device When Plugged In

Jan 5, 2012

I bought a new MP4 from ebay, and it came with a usb cable, however when I plug the usb cable in to my computer, it will not find the device. It will only charge.

View 2 Replies View Related

High Definition Audio Device Not Plugged In?

Feb 21, 2012

my computer does not produce sound

View 1 Replies View Related

USB Device Not Recognized - But There Is No Usb Device Connected

Sep 4, 2011

It's recognized in device manager as "Unknown device". But I've not connected anything to pc. Also all of my usb ports are working at 1.1 speed. When I try to connect any device, I get the message "that it could work faster, if i connect it to hi-speed usb port".

View 6 Replies View Related

Computer Doesn't Recognize Any Device Plugged Into USB Ports

Nov 17, 2012

Anything that I plug into the usb ports isn't recognized on my computer. When I plug something in, my computer doesn't make the usual "bloomp" sound and nothing pops up. When I search for my usb in my computer, it's not there. My computer acts like I didn't plug anything in.

View 4 Replies View Related

Dell 15r Inspire Has Black Screen And Wont Do F8?

May 1, 2012

i have a dell 15r inspire laptop with windows 7 and when i came to open it there is only a blck screen and a flashing curser line in the left hand top i have tried lots of times to start it and click F8 and nothing happens when i do F2 that opens but not the safe start mode before that happend there was a message saying that my macafee needed upgrading so i clicked yes then it went blank and a black screen is there some way of getting it to boot i am passed myself as i have just bought it a few weeks ago

View 3 Replies View Related

USB Device Not Recognized?

Apr 22, 2011

I am getting a constant error. When the error happens I hear the usb connection alert sound and a pop box appears in the lower right corner of my screen. I tried installing the chipset drivers again and when that didn't work i did a system reinstall. The only us devices I am using is my wired mouse and keyboard. Both usb devices work.

View 1 Replies View Related

USB Device Not Recognized

Nov 5, 2011

While working on my laptop yesterday evening, my mouse & external hdd stopped responding. On ejecting & re-inserting them both started getting this message 'USB Device Not Recognized'.Now none of my three USB ports are working. Though on cross checking, the devices are working on other machine.The message is getting flashed repeatedly. Also, observed that my battery got drained while it was switched off throughout the night. Have never faced either of these issues with almost 20months of working with Windows 7 Pro.

View 4 Replies View Related

USB Device Not Recognized?

Jan 11, 2012

Ever since I moved into my new apartment a month ago I've been having problems with my USB mouse. I got a new one for christmas and the problems still persist. When i first moved in it was working ok but randomly not working then it finally gave out. Every time i insert the mouse receiver it would be like rolling the dice whether it would work or not. I've tried my tablet and my memory stick as well and those don't work either so i know its not a problem with the mouse.I've looked through forums online and have tried almost everything:I unplugged the power cord waited and plugged it back in.I've uninstalled all of the USB Root HubsI've unchecked the Allow the computer to turn off this device to save powerI've updated my ChipsetI've updated my BIOSI've tried Microsoft FixitI've installed the driver for the mouse from its website.

View 3 Replies View Related

USB Device Not Recognized

Dec 31, 2011

when i plug my Ipod 4g an message at the bottom of my page says USB Device not Recognized One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it.

View 2 Replies View Related

USB Device Not Getting Recognized

Jan 28, 2012

USB device not recognized.

View 1 Replies View Related

USB Device Not Recognized?

Apr 14, 2012

I keep receiving this popup in the taskbar. Tried disabling it, dindn't work. I wish to rectify this and I believe my computer thinks this device is wrongly connected or faulty when actually none exist. I left all USB ports unused yet I get this problem.

View 2 Replies View Related

USB Device Not Recognized In Windows 7?

May 24, 2012

I am trying to connect a Blue Snowball USB Microphone to record stuff with but when I plug it into the USB port it doesn't work. Windows recognizes the device and starts trying to install the drivers but then it fails and gives no explanation. In Device Manager it shows up as "Blue Snowball" but has a yellow exclamation point next to it. When I click on it and try to install drivers it says that there are no drivers available. The light is on the device so it's getting power. I checked their troubleshooting guide and turned the USB cord in the other direction. I've restarted my computer a few times, all to no avail. I am using USB 2.0 ports and my OS is Windows 7 - Professional 32-bit.

I consider the sound card but I can play music and use skype (if I connect a 3.5mm POS microphone to the back) just fine.

View 14 Replies View Related

USB Device Not Recognized, Only At 4/12 Ports

Oct 11, 2009

I have Kingston 2GB DataTraveler (DT) and windows 7 RTM 64bit does not recognize it when pluged into 2 front usb ports or 2 top back usb ports. Other 6 lower back ports work. I have Gigabyte GA-EP35-DS3 mobo. This mobo has 8 usb on the back and 2 usb headers. One header is used for Codegen 7in1 cardreader+1usb port, other is used for 2 front panel usb ports. Few things ive noticed:

1) my old apacer mp3 player works on all usb ports.

2) most of new higher capacity usb's are not recognized in those malfuncioning ports

3) if i plug DT into Codegen's USB port, DT is then recognized on all ports

I've read this thread, tried instaling new Intel's Infs, tried removing all usb devices exept Codegen's. No effect. Any suggestions for my case?

View 0 Replies View Related

USB Device Not Recognized Only In Win7

May 8, 2009

I have a WD Passport 160GB portable HDD, which worked fine in XP on the same computer before I installed Windows 7.

As many other people experienced, the once the device is connected, it will show USB device not recognized. However, my mouse and keyboard, which are USB also, are working flawlessly.

Besides the Passport, I have a Maxtor External HDD which is not working also, I tried every single USB port on the computer and it just won't work. And this one is powered by a small power adapter, so it should not be anything related to USB power. On the other hand, the Maxtor HDD is visible from BIOS, just not in Windows 7.

My computer is single boot Windows 7 RC 64bit, clean install.

I'm using Q6600, Foxconn MARS P35 mobo, Seagate 7200.10 250GB HDD, PNY 8600GT, OCZ 2x2GB DDR2 800 ram. I don't think the hardware have any problem since in XP everything worked fine, and all the drivers are up to date according to the device manager in Windows 7.

Any advice?

View 9 Replies View Related

Iphone USB Device Is Not Recognized?

May 10, 2011

I recently used my new iphone USB got from Fry's (i used before without any problems) to my windows computer -- used itunes no problems -- any backups no problems. Suddenly it stopped working as it is not getting recognized by my computer. Now, getting error 43 on my device manager. I have windows 7 ultimate.I also used my usb with my ipod and iphone to my usb port in my car to use to play music and it cannot recognize it now. My radio turns off when I plug this in. My usb cable is new!! WTH! Then i used another usb in my computer and still won't budge! no recognition? Then used it in my car then to my work computer then to my laptopn and both usb's are not recognized. WTH?Note, all other usb devices work in my computer i.e.: External HDD and mouse/printer BUT my (2) usb cables don't work.

View 3 Replies View Related

USB Device No Longer Recognized?

Nov 13, 2011

I don't get the device not recognized. When I plug device into usb nothing happens

View 2 Replies View Related

USB Device Is Recognized But Cannot Open?

Sep 22, 2012

i play my usb with my panasonic recorder and when i try to use it with labtop
it recognized it but can not read

View 1 Replies View Related

CD Isn't Recognized As A Boot-able Device

Dec 8, 2012

I have recently replaced my laptop with a new hard drive and extra 4GB ram slot,My laptop is a samsung np400b5b-s02uk, i've put in a Seagate 750GB SATA-II HD and a 4GB 1333MHZ Corsair Ram slot, I am trying to install Windows 7 Home (x64) onto it, i insert the disc into the drive but a message appears saying boot device not recognised, i've selected it to boot from CD in the BIOS but still nothing.

View 2 Replies View Related

Intuos 4 + Windows 7 = USB Device Not Recognized

Jul 23, 2010

I've been encountering error Code 43.I've tried a lot and I am running out of options.I'm working on an Acer Aspire 5542G.My operating system is Windows 7.The USB device not being recognized is my Wacom Intuos 4 PTK.

- I've de-installed and re-installed my tablet driver.

- I've shut down and turned on the laptop.

- I've returned the laptop to original factory settings.

- I've taken the battery out, and put it back in again.

- I've de-installed and re-installed universal serial bus controllers.

- I've used CCleaner to clear up my register.

- I've used my google-fu to it's full extent, but I haven't found a fix.

View 8 Replies View Related

Xbox 360 Controller - Device Not Recognized

Jul 13, 2011

I've been having an issue with the xbox 360 wired controller since I built my new pc. When I plug it in via usb the device is not recognized by windows and no matter what I try it simply will not work.

Things I have tried: downloaded chipset drivers downloaded Software Downloads: Xbox 360 Controller for Windows tried the whole leaving the computer and all usb devices unplugged and off for a good few hours. ininstalled all the usb controllers and rebooted tried it in all usb ports, 3.0 and 2.0 searching for hours on google tried enabling/disabling usb legacy support in the bios tried running microsoft fixit thing (whatever that is) tried updating the drivers manually through the device manager but windows insists that the device is up to date. tried uninstalling and removing ethernet cable to try and force me to choose drivers. windows is fully updated I even bought a new controller thinking the last one was broken. The controller powers up when you plug it in, you can clearly see the green lights around the guide button flash but then nothing happens.

View 5 Replies View Related

Unknown Device-USB Controller Not Recognized?

Jul 31, 2009

I had an "unknown device" show up in devices and printers a couple days ago. It was also listed in device manager and said it was a USB controller. Everything worked and I've not added any new hardware. I have 2 partitions both with Windows 7 and the error showed in both. I've found that others were having the same issue, some needed drivers, some said cables needed replaced. Before I got serious with the troubleshooting, I read up a little and found a forum that said you should shut down then disconnect the power cord, wait a couple minutes then power up. Sometimes the motherboard needs to reboot and the devices will be reloaded or reassigned as they should be. It worked for me, it was an easy fix to an annoying problem.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved