I just noticed that in Device Manager my printer is showing in the disk drive section as a USB device, and in the printer section it is also listed, where it shows my printer as a (DOT4PRINT), and lists a printer as: Printer IEEE 1284.4 compatible.
My friend's laptop (Acer Aspire One 722 - Windows 7 x64) has been shut down after opening an email and Windows never started up again. When you attempt to start up the windows, it stays the black screen and says "No bootable Device Found"! I inserted Windows Live Disk and loaded it (Windows XP Mini - Golden Edition). When I went to "My Computer", it did not show any local drive. I went to "Disk Management" and in there, there was also no unallocated or allocated space. I even removed the HDD and plugged it back in. No thing happened. Then I removed the RAM card and inserted it back. Again, nothing happened! By the way, HDD had movements when laptop was on (I had removed the beneath panel).I inserted Windows 7 Disk to install a fresh Windows 7. But when you get to the part where it asks you to choose the partition to install the operating Sustem, it shows one unallocated drive with 0 (Zero) capacity! The options to Delete and format are disable. Only the option "New" is active and it gives you (0) bite to partition!
I'm currently using a Windows 7 PC built by a friend of mine, but starting yesterday, its been acting up. The problem is there used to be two hard drives I can access, Drive B and Drive C. When I boot up the computer, BIOS only detects Drive C (if I'm not mistaken), and Disk Managements as well. I realized this when all the programs whose targets are on that drive are all broken on the desktop.So Drive B doesn't show up anywhere at all.
I have a 1 TB Western Digital Caviar Black hard disk. While installing Windows 7, a screen for hard disk partition was asked. I created 4 drives: 200 GB, 200 GB, 200 GB and 400 GB. And then the windows 7 got installed. But now when I log into my PC, I can only see first 3 200 GB drives. Where did my 400 GB drive go? What mistake did I do and how can I recover it back?
My computer has been running slow since we had all our files switched over from our old computer to our new one.It's an HP we got in December 2010. Programs run slow and whenever we turn the computer on from sleep mode,it usually takes 30 seconds or so to get anything requiring an internet connection to fully work. Disks won't open most of the time and I can't install anything. Whenever we try to scan our computer for viruses, it will end up telling us it couldn't finish the scan because it wasn't able to scan a certain file.
current printer: HP office jet 6500AI have had the same problem twice on 2 different windows operating systems with 2 different HP printers?Both time were for my parents. One with was with XP the other Windows7. They try to connect a HP printer with USB hoping it will get autodetected and windows will have the driver, it doesnt, they call me. I download what HP calls a driver but its a huge files (I think one was 30mb and the current one even more). I got around the first problem by installing the old printer to the XP through their router instead of USB but now they do not have a router. I think the printer is about a year old, the PC is new. So I googled the HP office jet 6500A and tried the two suggestions I found (right click, properties, run in vista mode and the other was a new usb cable....) but neither worked.
I tried to reformat my dads hard drive to reinstall windows 7. It was in 2 partitions, so I ran the windows 7 disc and it ran through the motions, I formatted the c to re-install windows and it wouldn't let me. I went into dos under diskpart to try and format it that way, still no luck. I connected it to my computer then under disk management deleted the 2 partitions so there was only 1 now which had the size i.e, 600GB Unallocated. I connected it back into my dads computer and ran the set-up again. Now the computer wont even detect the drive. I need to re-format the drive to like factory default, is this possible, also do I have to do it in dos.
I have a format activity on my laptop. Before formatting, I had two partitions. Now after formatting I am able to locate the other partition via disk management service. but it is not showing under my computer. What should I do?
When i connect a sata hard disk which is loaded with windows 7 as a secondary to another windows 7 system to take the data backup it is not showing the drives but i can see it in the device management in windows 7.
i keep geting this poping up on scan my speed is dead shoud be at 16Mbs , its at 157kbs it slowing every thing i think . i have a new modem router a netcom nb604n
i have 500gb external hard disk n 3 partition in it.. now al 3 disks am not able to open . tried formatting but it gives error msg saying i cant format the disk..tried using command prompt as well but no use .so how can i format the diskd now?
my computer is acer aspire 3630.i have windows 7 32 bit os.my philips dvd drive is now not detected by my computer.when i was installing a game,beause of low battery,my computer shutted down.when i started it again,my dvd drive is not detected.it is not showing in the device manager and bios manager.what shall i do.
I plugged in my eSATA drive while CrystalDiskInfo was running and the computer froze. There was no way to regain control of the computer so I restarted.So now this eSATA drive is not recognized by the computer. The eSATA drive works in another computer.What's really weird is that another eSATA drive I have works in the computer where the crash happened.I've tried uninstalling all drivers (both hidden and visible) in Device Manager that relate to the drive.
i have this problem whereby whenever i resume the computer from sleep, the dvd drive disappear from "my computer" and device manager. It could not be detected as well. All the hard disks were detected.
The only way was to restart the computer.
The dvd drive is connected via the IDE cable to the mobo , using the Jmicron IDE/Raid chipset.
so I got a new asus P8z68-V pro motherboard. Im re-using my current 750gb SATA drive. I plugged it into the sata port, and start the computer. When it starts it says "no hard drive is detected!" I go into the bios, and on the bottom it has a disk drive, and a SATA drive. It recognizes that the sata drive is there, but when i go to start up it says no hard drive is detected. I have tried a few different sata ports and it is the exact same thing.
I've got an issue during post installation. One of my hard drive is never given a drive letter, but it does show up as a possible install drive during setup.
I always have to go into Drive Management and assign that drive a letter (and moving my DVD drive down a letter to keep the letters in order).
Under Drive Management the drive has the Properties (System, Active, Primary Partition), so I'm wondering if that is the issue.
Is there a way to change Drive Properties (if that is the case)?
my acer computer stop-ed working while been surfing net, first frozen ,switch it off by pressing power button, then comes message :reboot and select proper boot device, i checked the bios then nor hard drive western segate 1tb neather dvd been detected. i tried to hold f10 but does not work?
having an issue with a brand new HD I bought. Right now Windows 7 will not detect the HD as a drive.It shows up in the BIOS correctly, but not in My Computer. It is in a Frankenstein setup: SATA connection into the SATA port on the MB (it is enabled and showing), with power from an external HD enclosure.I don't think that would affect it though, as it is just drawing power from a different PS.i did some digging and found it in the System Information under 'discs' instead of 'drives' like my original HD.[URL]...
my pendrive is not detected in any computer where all other pendrives are being detected and problem is my inmportrant data is in the ones which is not beng detected?
for some reason my internal hard drive after installing it and reinstalling windows 7 it does not show up for some reason... I have check the cords to make sure they are in correctly
My Boot menu says it's there but my OS does not see it?