Network Lan Connection Windows Xp And 7 Computer?
Jul 18, 2011
computer #1: windows 7 hpcomputer #2: windows xp proI managed to lan cable connect and share folders/files between 2 windows 7computers. And the same between 2 windows xp computers.Then I wanted to lan cable connect and share folders/files between a windows 7 hp and a windows xp pro computerI tried for hours, running the same settings in circle.At a point it worked. But I don't know why it suddenly worked.The difficult thing was, to make the network icon appear on "the other computer".Do you have a detailed step by step manual, on how to config settings in
View 1 Replies
ADVERTISEMENT
Jan 7, 2012
I have 3 computers running Windows 7 Ultimate x64.
I connect them to a hub and set a workgroup name. Everything is working fine. All of them are able to see each other and access their shared drives.
However, once I unplug internet line (all computers still connect to the same hub), computer cannot see each other and cannot access shared drives anymore. Also, workgroup name is changed to 'Unidentified Network'.
What should I do to connect to a network without internet connection?
View 3 Replies
View Related
Jan 12, 2012
I have a hp compaq laptop and am able to use the wireless internet connection..however I also have a Dell Inspiron notebook, a few days ago I lost internet connection on the dell but the HP was still connected. I have contacted my internet provider and they say there are no connection problems and all is fine. They think the problem is on the dell unit. I have tried disabling and enabling the Lan and wireless network connection. The system recognizes the wireless router but wont connect to it why and what can I do.
View 7 Replies
View Related
Nov 11, 2010
For some reason my router and modem will not show correctly on my dell inspirion one desktop. Im running windows 7 and here are the net work connection deatils
Connection -specific DNS Belkin
Description Realtek PCIe GBE Family Controller
Physical Address 00-00-00-00-00-00
DCHP Enabled Yes
Ipv4 Address 192.168.2.2
Ipv4 Subnet Mask 255.255.255.0
Lease obtained Wednesday, November 10, 2010 9:45 PM
Lease Expires Sunday, December 18, 2146 4:17 AM
IPv4 Default Gateway 192.168.2.1
Ipv4 DHCP Server 192.168.2.1
Ipv4 DNS Server 192.168.2.1
IPv4 WINS Server
NetBIOS over Tcpip enabled Yes
The Connection was working about ten days ago and then suddenly stopped and read as an unidentified network no internet access. at one point is was not receiving packets but now it is but it still says no internet access on the IPv4 Connectivity. Media state is also enabled and the speed is 100.0 Mbps when i troubleshoot it says windows cant identify problem but in the details it says default gateway is available. when i use the cmd prompt ipconfig/all my local ethernet adapter has a physical address of all zeros.
View 9 Replies
View Related
May 12, 2011
Recently when I try and connect to the internet my wireless connection network says it is an unidentified network with no internet access. This never happened before.
View 2 Replies
View Related
Apr 22, 2011
I have a Dell inspiron mini tower that had some apparently critical either net driver deleted. I'm not entirely sure which driver it was or how to get it back. I've tried downloading a few drivers on another machine and then just transferring them to the bad one but it's not working (3 separate ones now). It was working perfectly before this "thing" was accidentally uninstalled.
View 8 Replies
View Related
Aug 11, 2011
I connected two notebooks via a TP-Link router (Wlan 54g). The first computer is a brand new Samsung RF511 Windows 7 Home Premium 64bit with Intel I7, 8GB Ram. The second is a 5 year old HP Pavilion DV5000 device with Windows 7 Home Premium 32bit.
It dosent matter if i connect via Homegroup or direct over the network to the files. The speed of transmission between the two computers is about 3-400KB. Sometime, i get about 7-800 KB.
View 2 Replies
View Related
Aug 31, 2011
I have an internet connection, but it is not recognized by Windows. I have tried repeatedly to set up a wired network connection but it does not work.
View 15 Replies
View Related
Jan 25, 2012
win 7 64 bit Cisco wyfi, D-link router, IP address missing, computer says its connected but no internet access. How can I set an IP address?
View 2 Replies
View Related
Jun 22, 2011
I have a network set up with file sharing. I use a Windows 7 PC to host files that are shared with around 8 other PCs - some on Windows 7, some on Windows XP. The file sharing works but sometimes some users are unable to get access to the files. The error message is something like \PCNAME is not accessible. The user can connect if the machine storing the files is restarted but it will happen 4-5 times during the day.
View 3 Replies
View Related
May 2, 2011
I have a 3 PC router based workgroup network. 2 PCs are XP SP 3, one PC is Windows 7 When all PCs are wired, everything works just fine. All PCs (W7 and XP) can see and share files with all other PCs (It took a bit of doing but I got there eventually)If I try to connect the W7 PC wirelessly,
* the W7 PC cannot access/share files on the XP machines
* the XP machines can see and share files on the W7 PC
* The W7 PC can access the router and can ping the other PCs
There is no firewall in operation on the XP machine What do I need to do to get the W7 machine to access/share files on the XP machine via wireless connection?
View 14 Replies
View Related
Mar 28, 2011
Alright I am running Windows 7 X64 Bit. I am running a Linksys AE1000 wireless adapter with a Linksys router with Comcast cable. Anyway here is my problem. Before I didn't have to configure the IP4 settings as it was set automatically obtain IP and DNS settings. But now I have to put in those values manually to get online because if I don't I get the unidentified network in my the network area.I have done the following setting adjustments:-Disabled the bonjour service.
View 1 Replies
View Related
Mar 30, 2012
Just reinstalled my windows 7 home premium after having some issues and thus far everything is working swell, except for the fact that I can't seem to find any wireless connections under connections available- I can't even seem to set up wireless connections.
I know nothing is wrong inside the computer since my splash top allows me to go onto the internet wirelessly- so I'm guessing this has something to do with me just installing windows 7 home premium again.
Without the internet I can't download drivers or get windows updates-
Looked in device manager and there are three exclamations next to these drivers:
standard VGA Graphics Adapter
Network Controller
Unknown device
Can't seem to fix the exclamations since I can't get internet access (only have wireless net) Is there anything I can download and burn to get these drivers working?
View 2 Replies
View Related
Nov 9, 2012
my HP 6500A plus printer (wireless) all of a sudden I can't scan or use printer to print normal documents.
View 7 Replies
View Related
Oct 26, 2011
(the bytes sent and received). It seems skype calls and watching in browser videos shoot them up into the billions after a few hours +. Upon googling around i am quite alarmed. Why did my network randomly change to "network 3"? A few weeks ago it just said 'network'?
View 7 Replies
View Related
Jun 4, 2011
A week ago I put together a new computer and installed Windows 7 Ultimate 64 Bit, every thingy installed just fine even the Ethernet drivers that came with the Motherboard disk installed ok, but I get 'Unidentified Network' for my network and only local connection. I have reinstalled the drivers many times. I am on another computer hooked up to the same router and modem, but it is running Vista instead, but the internet works just fine, and it is using the same cable as my other computer so it can't be the cable.
My computer Specs:
AMD Phenom II X6 1090T Black Edition Thuban 3.2GHz
MSI NF750-G55 AM3 NVIDIA nForce 750a SLI HDMI ATX AMD Motherboard
EVGA 1GeForce GTX 550 Ti (Fermi) [2x - Sli]
SAMSUNG 1TB 7200rpm Hard drive
G.SKILL Ripjaws Series 8GB (2 x 4GB)
View 9 Replies
View Related
Sep 3, 2012
I have been having this trouble for awhile now where after Windows 7 loads, I do not immediately connect to the internet through a fixed hardwired connection. It is delayed by about 2-3 minutes. I have changed cables many times, refreshed my IP Config, released it, etc. Nothing has yet to seem to work.
View 5 Replies
View Related
Dec 17, 2012
My network cards drop the connection and are listed as "unplugged" every time I game online, regardless of the game. I have 2 internal Realtek PCI GBE family controllers on an ABIT IP35Pro mobo. There is no set instance of why/when this happens only that it is completely random and I get the usual Event ID's in the system log after it happens:
The TCP/IP NetBIOS Helper service was successfully sent a stop control.
The reason specified was: 0x40030011 [Operating System: Network Connectivity (Planned)]
The Computer Browser service was successfully sent a stop control.
The reason specified was: 0x40030011 [Operating System: Network Connectivity (Planned)]
There are no other events, Application or Security that happen right before these events other than MS Application experience service entered the stopped state in system log. It could happen every few hours during the day to every 5-10 minutes after midnight( this is what is very weird since it did not do this prior to midnight this many times ). I sit behind a uverse router with it passing through a gateway from 2 powerline adapters. I have no problems downloading torrents, watching movies or anything l else strenuous on the network, but gaming. The only fix I have found is to disable the card and re-enable every time.
I have tried the fixes below with no luck.
1) Disabled Computer Browser service
2) Disabled TCP/Ip Netbios Service
3) Updated Realtek drivers
4) Rolled back Realtek drivers
5) Changed IP address
6) Reset TCP/IP Stack
7) Completely blew out Windows 7 Home and installed a fresh Windows 7 Ultimate I had
8) Disabled windows 7 from shutting these cards off
9) changed power management to never sleep the system
View 2 Replies
View Related
Jul 8, 2011
Ok, I'm going to give a small amount of back story here as it may be relevant to the current problem. Yesterday I formatted my Win XP PC and tried to install Windows 7 on it. 3/4 of the way through the installation my PC would restart, and upon loading back into windows I would receive this error message:�The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install Windows, click to restart the computer, and then restart the installatioThere were a number of possible fixes to this problem detailed hereI eventually got the installation to complete properly by removing my Sound Card and my Network Card.Ok, now onto the current problem. As stated, I have a new, clean install of Windows 7 32 which seems unable to connect to our BT Home Hub router. I have an ethernet connection to the router (lights: check, and cables are secure etc) and also a Wireless Network Card which may or may not be in a functioning state. By which I mean, I have had problems with it in the past but I can't remember exactly what is wrong with it. However, as I did with my XP install I want to connect via the ethernet cable.
In the Network and Sharing Center there are no networks listed.I have attempted to update the drivers for my MB and the Network Card, neither of which seemed to do anything.If I try to ping google or anywhere else it fails.This could end up being a very simple issue, but I'm completely new to Windows 7 (and skipped Vista) so I don't really no where to go from here, and am kind of burned out after spending 8 hours yesterday just installing windows.My PC specs:Custom BuiltOS: Windows 732bitMOBO: ASUS M2N4-SLICPU: AMD Dual Core 3 GHzGfx Card: GeForce GTS 250Network Card: Realtek 8185
View 8 Replies
View Related
Aug 21, 2012
My computer crashed and i have no internet for one of my three computers it says Wireless Network Connection doesn't have Valid IP Configuration?
View 1 Replies
View Related
Dec 12, 2012
I am able to access the internet through my wireless work computer and xbox. my home dell laptop will not connect to the internet. It is showing that i am connected to the linksys but Access type says no internet connection. I have already tried and ran FSS.exe becuase thought it might be a malware issue.
View 1 Replies
View Related
Jun 10, 2009
i have problem to set up a new conection.please tell everyone how to set up a new connection.i cant make access my home network.After make new connection i see is public network not home network.i see there two connection there and in home network no internet access. how to make one home network connection.
View 6 Replies
View Related
Nov 6, 2009
i am thinking it it might be because i have bridged my connection for my 360, but i have a red x on my network connection but i still have full internet. i already searched and did many steps...even the cmd one but no luck. so could it be from my wired 360 via bridge connection?
View 6 Replies
View Related
Jul 2, 2011
I want to change DNS address but when in "Network connection properties" I select the "Internet Protocol Version 4 (TCP/IPv4) line the Properties button is not active and I can not click it to open and change the DNS address.Also I see now that Properties button is inactive for all the other lines too.. I can't find the reason of that..Did I restrict something by mistake? or is it another problem..I'm on Windows 7 Home Professional..
View 8 Replies
View Related
Apr 7, 2011
If I am connected to the network I am not able to logon. Once I disconnect the network cable I can logon and than I need to reconnect the cable again to be able to work properly.If I lock the screen and I want to unlock it again I need to disconnect the network cable to be able to logon.See the pic for the error messages: (its in dutch sorry)We tried to remove the object in AD and added it again but no joy. All accounts (also admin accounts) on the machine have the same impact
View 8 Replies
View Related
Feb 3, 2011
I am having an issue with a windows 7 laptop (premium)If I am connected to the network I am not able to logon. Once I disconnect the network cable I can logon and than I need to reconnect the cable again to be able to work properly.If I lock the screen and I want to unlock it again I need to disconnect the network cable to be able to logon.SWe tried to remove the object in AD and added it again but no joy. All accounts (also admin accounts) on the machine have the same impact.
View 2 Replies
View Related
Jul 16, 2009
I have RC 7100x64 connected (per cat cable) to a wireless router. Windows 7 created a home network. Router is perfectly fine and my 2 laptops automatically login into the internet. In the beginning my despktop also jsut was able to be online after booting up.
At some point (I did all updates, installed all my software) the PC does not connect to the internet anymore. Tehonly way to get online is to:
- open Network Center
- leftclick "Connections: local area connection" --> disable
- go to trouble shoot problems
- then it finds " the local area network adapter is disabled"
- I click " fix it" and it will work.
I attached the screens
How can I make it connect automatically (as it did before)? I set all services I could think of to " automatic" (IP Helper etc.). From researching I read that XP had a similar problem with SP3. not sure if it is related, but coudl an update be at fault?
Everything is up to date, Kasperksy keeps viruses away, I did not do one of the registry-cleaner tools.
Since it worked at first, one of my isntallations or updates must have done it. I also did some of the "service optimizations" from here bu tundid all of them to resolve my problem.
One could say I should isntall a newer built, but first I just want to use it before I buy the real deal in October. Second, it used to work with RC 7100 and going through all the trouble reinstalling is a hassle.
Everything else works well.
View 5 Replies
View Related
Oct 9, 2011
Out of the blue, I lost my Network and Internet connectivity Windows 7 gave me excellent troubleshooting tips like to check if I have a cable connected.Device manager tells me that my network adapter is working properly (Realtek GBE).When I try to connect to a network it tells me no network connection found. The machine is still configured as it was out of the box (relatively new machine - Dell XPS Studio 9100 - Windows 7 Home Edition 64 Bit). It been working fine for almost a year. I sincerely hope reformatting and reinstalling Windows 7 is not the answer to every windows 7 problem
View 9 Replies
View Related
Feb 26, 2012
So, we have a network of about one terabyte of storage on it. It is normally connected to my laptop, a desktop and our Playstation 3. Obviously it connects via internet with our wireless router and such but for some reason it won't connect to my laptop? I have everything except a few programs on the network (Everything from my documents to my pictures to my other programs are stored on the network)...thus not being able to access it is a HUGE difficulty
View 2 Replies
View Related
May 28, 2012
I am doing some troubleshooting and I want to completely remove my network connection. I remember with Windows XP when I did this, it would re-detect the network card and reload the drivers and settings after I rebooted.
I can disable the connection but not delete. How do I remove the connection in Windows 7 x64?
View 1 Replies
View Related
Jul 22, 2012
My computer took so long to identify network and lately it cannot identify anymore.
View 1 Replies
View Related