IP Protocol Disappeared

Feb 23, 2012

I am trying to fix a Samsung laptop for a friend. She admits to having 'fiddled' with the networking applets in Control Panel with the result that neither LAN nor Wi-fi functions any more.I have noticed that I am unable to use the GUI to access IPv4 Properties because the button is greyed out. Also greyed out is Uninstall. The only button available is Install. I have tried that, but after rebooting the situation appears to be the same.I have tried using the command prompt as Administrator and using NETSH to uninstall IP, install it, reset it etc, rebooting every time but without any noticeable change afterwards. Also tried NETSH WINSOCK RESET after the above. I have also tried the above in recovery mode with networking enabled. Again, no change!Unfortunately, the model does not have a CD drive. However, it has USB ports. Fortunately, I do have a generic 32-bit Win 7 Home Premium CD - which is the operating system installed on the PC. So I could copy the CD in one way or another to an external USB drive and work from that if necessary. If I knew what I had to do!There is a lot of valuable data on the PC and I don't want to be responsible for losing it. Of course, I could try backing it all up but she has saved stuff all over the place and I am bound to miss something! Yes, I could copy the entire disk ...... I know!! But we would still have to find and retrieve the data later.

View 4 Replies


ADVERTISEMENT

IP Protocol 'disappeared'

Feb 9, 2012

I am trying to fix a Samsung laptop for a friend. She admits to having 'fiddled' with the networking applets in Control Panel with the result that neither LAN nor Wi-fi functions any more.I have noticed that I am unable to use the GUI to access IPv4 Properties because the button is greyed out. Also greyed out is Uninstall. The only button available is Install. I have tried that, but after rebooting the situation appears to be the same. I have tried using the command prompt as Administrator and using NETSH to uninstall IP, install it, reset it etc, rebooting every time but without any noticeable change afterwards. Also tried NETSH WINSOCK RESET after the above. I have also tried the above in recovery mode with networking enabled. Again, no change!Unfortunately, the model does not have a CD drive. However, it has USB ports. Fortunately, I do have a generic 32-bit Win 7 Home Premium CD - which is the operating system installed on the PC. So I could copy the CD in one way or another to an external USB drive and work from that if necessary. If I knew what I had to do!There is a lot of valuable data on the PC and I don't want to be responsible for losing it. Of course, I could try backing it all up but she has saved stuff all over the place and I am bound to miss something! Yes, I could copy the entire disk ...... I know!! But we would still have to find and retrieve the data later.

View 3 Replies View Related

Remote Desktop Protocol Error?

Jan 12, 2009

When i am remote desktoping to one of our terminal servers from windows 7 and then shadowing a users session as soon as i connect to the users session via Terminal Services Manager I get the following error:'Because of a protocol error, this session will be disconnected. please try connecting to the remote computer again.'It appears to be a problem with windows 7 remote desktop, as i also have XP and Vista machines which i do the same on but they work fine!

View 9 Replies View Related

DNS_C Protocol Causes Lag Spikes Every 10-20 Seconds

Mar 4, 2012

I have noticed that svchost.exe is doing this connections every 10-20 seconds, and every 10-20 seconds there is a lag spike that jump the latency up to 1000ms and more.

I want to disabled this periodical connections that windows does...I don't know what Has caused this...I have tried completely disabling svchost.exe access to internet but than no application launched can connect to internet.

The connections are port specific, the remote ip to which it connects to is always 192.168.1.1:53, which for sure is the ip of the dns (redirected by the router) plus the port 53. I have tried completely disabling the access to this remote port for all the local ip and local ports with my firewall, but it just keeps avoiding it. I have used this method with the connections to microsoft with the port 3544 witch are being disabled.

View 2 Replies View Related

Can't Start Peer Name Resolution Protocol

Oct 14, 2009

Being somewhat bored I began playing around with Homegroups. I delved into HG awhile back but never really got into it. To make a long story short I can't start the service 'Peer Name Resolution Protocol' which is required for HG. There are 3 Peer type services. One is started (Peer Networking Identity Manager). The other one (Peer Networking Grouping) is not because it depends on 'Peer Name Resolution Protocol.' Both Homegroup services are started and I have IPV6 enabled on my NIC and in the LAN properties. Also the last time I played around with HG it seemed I needed the MS Firewall service started which it is. The event log has this: 'The Peer Name Resolution Protocol cloud did not start because the creation of the default identity failed with error code: 0x80630801.

View 9 Replies View Related

Get An Error Saying The Protocol (HTTP) Does Not Have A Registered Destination

Feb 19, 2012

When i try to open my shortcuts on my desktop,i get an error saying the protocol (http) does not have a registered destination. What can i do?

View 2 Replies View Related

Associating File Type Or Protocol With Program?

May 19, 2012

In Default Programs, When I select 'Associate a file type or protocol with a program'. When I select an extension and click the Change Program button, the program I want is not on the list, So I select [Browse] and select the program I want then nothing happens. How do I add a program to the list ?

View 2 Replies View Related

Upgrade Router Firmware To Support New Ip6 Protocol?

May 10, 2011

Should I upgrade the firmware of my netgear wndr3700 router so it will now support ip6 protocol instead of ip4. The update in in netgears website. The support for my router has expires so I would need to pay for support if there any problems.The netgear wndr3700 works perfectly right now with my computer and wireless blue ray player..

View 1 Replies View Related

Error In Tight VNC Viewer: Unsupported Protocol: RFB 004.001

Jan 15, 2013

I am seeing the following error when attempting to connect to a remote computer with TightVNC...

View 2 Replies View Related

Default Programs - Associate A File Type Or Protocol

May 16, 2009

How to Associate a File Type or Protocol Default Program in Window 7 ?

View 0 Replies View Related

Windows Live Mail Error ID Ox80004003 Protocol SMTP

Jul 18, 2011

- Cannot open ""New Message""
- Cannot send ""Mail Out""
- There are still 5 messages in ""Mail Out"' which cant be sent. Unknown error : smtp.ziggo, windows live mail error id -Ox80004003 protocol smtp, gate 25, safeguarded ssl : no
- Cannot ""Erase"", nor ""change to file "", messages from ""Mail in"".

View 1 Replies View Related

Protocol "http" Doesn't Have A Program?

Aug 31, 2012

In Windows 7 I cannot get shortcuts to open from my destop. I get the error message "The protocol "http" does not have a registered program". How do I fix this

View 5 Replies View Related

How To Associate A New "protocol" With An Existing Program

Nov 10, 2011

The control panel Default Programs options only work for programs that Windows 7 admits exist (with some VERY strange omissions, like MS Office) but it is easy to work around that by using windows explorer to let you associate any program that you can browse to with any file type that is already on your system.

BUT how to you associate a new "protocol" with a program (specifically Internet Explorer). My problem is that I have one email provider that automatically changes every incoming email hyperlink from http://etc to blockedhttp://etc

With WinXP and Outlook Express there was no problem because clicking on the link would automatically open IE8 which would of course fail to open the site, but I could easily click into the address bar and delete the "blocked" from in front of http

Now I'm running Windows 7 and Windows Live Mail and I can't get the links to open anything. When I click on the link, I get an error message "There is no probram associated to perform the requested action. Please install a program or, if one is already installed, create an association in the Default Programs control panel."

I have tried each of the functions under Default Programs and none of them will let you enter a NEW association. I found the one that says Internet Explorer is associated with http:// and https:// but there is no way to add any new protocol. Unlike filetypes you can't work around the protocols by using explorer.

View 2 Replies View Related

My BOOTMGR Has Disappeared

Jan 30, 2012

computer froze up...tried to restore system at three different restore points and was unsuccessful...Then tried to recover to factory settings which was also unsuccessful...According to HP the factory settings are corrupted....Cannot boot the system because the BOOT MGR is wiped out...Computer is dead in the water....Suspect computer virus that caused the system to freeze up.

View 1 Replies View Related

Windows 7 Disappeared?

Jul 22, 2012

The Dell Inspiron, with Windows 7, we bought our daughter last year worked fine until she left last May for an internship. We ran scan disc before the lap top was packed. When she arrived at her destinaction it did not work. According to the Geek squad, the hardware works fine, but there is not an operation system on the laptop. The laptop did not come with discs, but it has the Windows 7 label on the back with the product code. But when emailing Micrsoft support, they only want the PID which can't be retrieved from a computer that doesn't have an operating system.

View 3 Replies View Related

All Programs Are Disappeared

Mar 12, 2011

So, I'm on Home Premium 64 bit, and today everything was working just fine. After one reboot, nearly all the icons on my desktop were blank. As in, the individual icon pictures were just default. Every program I try to open all pops up with "Such and such file has been moved or Deleted" When running programs manually, I keep coming up with "Cannot run .ini or something to that effect if that helps. . The only thing I can get to work are Malwarebytes, Avira and Internet Explorer so far that I can find. No viruses have been detected by either of the scans and I just have no idea what to do from here. All MP3 files are also useless due to every media player that I have now appearing missing including WMP, Winamp, ITunes and such.

I really have no idea what to do here. The last thing I'd want is to have to format the computer. I have one 4gig thumb drive to back up some things, but that's about all I have. If those files aren't corrupted as well. I have no way of opening them to see.Tried a system restore before posting this and the restore failed.I know I am probably not providing all the information that I can, but if you need any more, please let me know. I'll be monitoring this thread all day.

View 2 Replies View Related

Windows 7 Disappeared From Mbr

May 11, 2011

I have had Windows 7 installed on my PC.Last night I installed Windows XP Professional (as i have some programs that do not work on 7) on my PC. I had intended it to be a sort of double boot with Windows 7 i.e. i wanted to have a boot selecter where i can choose whether to boot XP or 7. However my PC now directly boots into XP and does not allow me boot into 7.Is there a way to re-insert Windows 7 into the mbr so that i can have a choose which OS i want to boot?.

View 1 Replies View Related

Wallpaper Has Disappeared?

Jan 2, 2011

I decided to change wallpaper (desktop), but the new one didn't look nearly as good once it was on the computer. So I decided to go back to the previous wallpaper, except it has now disappeared. I've looked everywhere, and have followed various suggestions found on internet (namely on Windows 7 Forums), but to no avail.The previous wallpaper was NOT a pre-installed Microsoft wallpaper, but an image I had directly installed some months ago.I would do a search on my laptop, but cannot remember the title of the photo.Florio

View 5 Replies View Related

The Bar At The Top Of My Documents Has Disappeared

Nov 18, 2011

When I click on "My Documents" I often then go to the Desktop by clicking to the right of a small window/bar at the top. It then opens up "Desktop", which is just above it in the"family tree". I click on "Desktop" to quickly go to it.

Suddenly this bar has disappeared. How to I get it back again?

View 2 Replies View Related

C Partition Just Disappeared Along With OS?

Mar 5, 2012

my computer last night randomly shut off while loading a tv show off Internet. upon restarting windows failed to boot. when prompted with restore and recovery it failed. unable to access safe mode and when it says it is recovering it just says it is finished with no progress restarts to no avail. upon looking at command prompt diskpart, my c partition(30gb) no longer is visible or exists. this is where my windows seven was stored. so i now only have my e drive partition which is a (1 tb drive) repairs do not work, the only option i have is to install on my e drive which warns me it will overwrite my data. i would like my c drive back and be able to boot successfully.

View 7 Replies View Related

All Icons Are Disappeared

Feb 27, 2011

my start menu is not working also my all icons are disappeared

View 2 Replies View Related

Favorites Bar Disappeared?

Nov 7, 2011

Why has my windows 7 toolbar disappeared, and how do I get it back?

View 4 Replies View Related

Folders Have Disappeared?

May 12, 2012

Until recently, my Windows 7 desktop showed a series of large folders in thelower/center part of the screen for various files and photos, but now they'vedisappeared.

View 3 Replies View Related

The Toolbar Has Disappeared?

Sep 9, 2012

The tool bar (file, edit, view, insert, helps, etc. has disappeared) at the mid-top of windows 7 face page. How can I get it back?

View 2 Replies View Related

Ethernet Driver Has Disappeared

Jun 5, 2011

My D-Link router is not working virgin want me to connect my laptop to the router with the ethernet cable,but it appears I do not have an ethernet driver. I need to download one but from where? I have tried system restoring but it hasnt brought it back and they say they cant fix my router until the driver is there. my other driver are realtek and I am using windows 7.

View 3 Replies View Related

My Hosts File Disappeared

Jun 13, 2011

Yesterday I realized my hosts file went missing. This happened within the last week. UAC is on and my computer is clean so I assume this wasn't caused by malware, but I'd like to know what program did this. Is there any sort of log I can access that will show me that information?

View 3 Replies View Related

Icons On Desktop Have All Disappeared

Jun 18, 2011

For some strange reason my icon on the desktop have all disappeared. I can find them when I go to Documents and click on desktop but I can't seem to put them back on the desktop.

View 5 Replies View Related

Favorite Links Disappeared?

Sep 7, 2011

I got the rogue fake virus, the one that looks like MS windows doing scans etc... Anyhow, I got rid of it but my links in the favorites bar have all but disappeared. I can locate the favorites file with a search and all my links are in there but for the life of me I can't remember how to move them back to where they belong, in the favorites menu bar in IE.

View 7 Replies View Related

All Desktop Icons Disappeared?

Nov 17, 2011

I installed Nero Kwik Media successfully and all the desktop icons disappeared. I cannot drag them from the Start menu. I have WIN7.Any suggestions what I should do to get them back? By the way, I uninstalled the program thinking that maybe the desktop icons would come back. Of course, they didn't..

View 7 Replies View Related

Toolbar Disappeared With Favorites On It?

Feb 7, 2012

My Tool bar disappeared with my favorites on it!

View 1 Replies View Related

Desktop Icons Have Disappeared

Sep 6, 2012

The issue I need assistance with is that my desktop icons (graphics only) have dissapeared. The text remains and if I click on the text I am directed to the programme. I have checked the location of the graphics on the system and they are still there.During this time I have also had intermittent error messages which appear for seconds "Windows Explorer is not working" and then it reloads and I can continue. but still no icons.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved