I am trying to install windows 7 upgrade from a bootable dvd. I get the prompt to install and then it thinks for a while and comes back with the message:"A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVD or USB flash drive, please insert it now.
Note: If the Windows installation media is in the CD/DVD drive, you can safely remove it for this step."
I looked around the web and noticed this was a common issue with Vista, but I cannot seem to get it past this point. I have tried pointing it to any and all possible drivers I can think of for the IDE, SATA, motherboard, etc.
Then I decided to just try it from within windows xp, and it worked. I was able to install everything fine. So my question is if it can be installed from the disk like it appears everyone is saying, or if certain hardware requires it to be done from within windows.
I tried copying the driver folder from the system32 folder after 7 had been installed hoping the needed drivers would be in there, but when I browsed to it, it said no device drivers found.
Any suggestions around this? Is it even necessary? I am wanting a system that would be equivalent to formatting the hdd and then installing. Do I get that by installing within XP and then deleting the windows.old folder?
This is a relatively older Dell XPS 400, although everything worked fine once 7 was installed from within xp.
I have few questions on Windows 7 Upgrade. Currently I'm using windows vista home premium 64 bit and I bought an windows 7 home premium 64 bit upgrade disk.
first thing is I want to format my previous operating system and all the data in my laptop and install windows 7 in it using the Upgrade disk.
second thing is I don't have my vista installation disk with, my laptop was pre-installed with vista so in future if I want to switch can I get back VISTA using system restore.
third is can i install windows 7 on a new hard disk using a windows 7 Upgrade disk?
Per microsoft I need to do try a repair install from original disk. Is there a difference between running repair install from Windows or booting from original disk then selecting upgrade install? Is one or the other preferred? Directions say both attempt to preserve installed programs, but not all drivers, and both require reinstalling all the 60 or so windows updates released after my disk. so no differences there.
OK So to begin Im upgrading from windows XP Professional.. Before I decided to up grade I ran into this error on my PC: C:windowssystem32configsystem missing or corrupt
I tried the recovery disk and pressing r and typing in the commands in microsofts website and it said: access denied (or something along those lines) Ok so I gave up on that and when I start the computer I can go into BIOS and everything but as soon as it hits the screen where "windows didnt start last time, safe mode, blah, last known good configuration. If select any of them it freezes and if I allow the countdown it usually goes to a white / black screen and says that error up there ^^.
We couldnt get it fixed so I decided that I would upgrade to windows 7 and I purchased it online and downloaded it and it WILL not work with the computer. I go into BIOS and set CD/DVD first and press a key to boot from disk and it just restarts as soon as it loads and keeps redoing it. Occasionally Ill get a " the file is possibly corrupt, the file header checksum does not match the computed checksum.
I have Vista Ultimate installed today. I intend on buying Windows 7 Home Premium upgrade. I would like to install 7 on a new WD Caviar Black I just ordered as a clean install.
1) Is this possible or will Win 7 flag this as a new install because of the new HD and not let me proceed since I plan on buying an upgrade disk?
2) If not, what options do I have?
3) If I can do this, can I plug my old drive in as Drive D: or E: to transfer the data over?
Is it possible to do a fresh installation from a Windows 7 Professional Upgrade disk? I pre-ordered it, not thinking that I would be upgrading from a Windows 7 Ultimate RC. I really want to be able to start fresh and stuff. Is this possible in anyway?
I do have a recovery disc from HP, but I *really* don't want all of their crapware on my computer. Using the recovery is the worst possible scenario in this situation.
So, I need to know if I can install windows 7 x64 via direct boot when I start up my computer it is in ISO format. So like my default boot will be my DVD drive to install it. can I do that with it being ISO format?
I recently bought the full retail Windows 7 Home Premium, I installed it on my pc and everything is going great. I also have a copy of the upgrade offered to students and a valid key for that.
My brother wants to install Windows 7 on his comp (He's running windows vista premium 64) and I was wondering if I could use my Windows 7 installation disk to install it, and then just use the upgrade key to activate it? I want to do a custom (clean) install over windows vista, and then delete the windows.old folder.
I don't see a problem and a disk seems easier than that .exe file you get from downloading on digital river, so I was just wondering if it would work.
Guys my first post and I have looked at the tutorials just wanting to clear up a few things. I have Windows Vista Home 32 Bit and upgraded to Windows 7 Pro 64 bit. I installed a new HDD at the time as I wanted Windows 7 on that instead of on the Vista drive. That has left me with the little issue of the product key not being valid, as I didn't install on the top of the older system.
Now I will need to activate it at some point and have just come across the forum and your excellent tutorials, now you have linked to Paul Thurrott's guide and he mentions a double install method which is supported by Microsoft. I would prefer this route as it looks easy, and less likely that I will do it wrong. My main questions are when I installed Windows 7 I stupidly clicked the Activate Online thing. Will double install or any of the other methods still work? Will the double install lose all my upgrades I have had to make to get all my devices working?
not to bothered but would prefer this not to happen as it took me 3 days to do my drivers and various other installs to get back to being able to run fully. Anyway so far I am very impressed by Windows 7 and well Vista will never be used again and once I have this little issue sorted I may well be getting rid of vista of my other HDD.
Just one final question how much RAM can I install now that I am running Windows 7 64 bit, I currently have 2gb (1gb per channel for processor). I know what type to get but what is the Maximum it will take for the OS. Anyway I know it is Christmas and not to fussed if I get a reply tonight or tomorrow, I hope some one can help me. Finally I would like to wish everyone a Merry Christmas.
I have a W7 upgrade disk which I purchase when W7 was release and my l copy of Windows XP SP2. Is there any way I can just install W7 on a newly formatted harddrive.
Reason:
I have a trojan virus they cannot be deleted, it can only be quaranteen. Unfortunately while quaranteened, it still creates temp files...more than a 100. After trying numerous outlets: Symantec, my product is Syamantec Endpoint Protection., Mcafee on-line, Trend Micro House Call and Web Root Secure anywhere, I am afraid I will have to reformat the drive andi install from scratch.
Well i am currently running Vista Home Premium sp2 and Windows 7 Ultimate (build 7100) in a dual boot config for about 2-3months and loving it. I was wondering if i could upgrade my Windows 7 install to RTM without affecting my Vista install? Do you get a choice which OS you want to upgrade or does it go by what OS you load the upgrade disc from?
My toshiba c650 laptop recently acquired a virus and now it will not boot. I was running windows 7 home premium 64bit at the time with ubuntu 11.10( I think) my computer crashed while I was running a mcafee scan and has not booted since ubuntu also does not boot due to the windows 7 system failure. Any way I was wondering if I bought a windows professional 64bit upgrade, could I Install it from boot? I also need to know if it would wipe all virus's from the hard drive. It would be best to mention that I have tried safe mode, safe mode with networking, my recovery discs and a blue screen repair discs all that happens when running these is a black screen with white cursor I left them all for an hour to see if anything happens but sadly nothing does.
I have vista on my first partition, 7rc on the third (second is vista data).
I had read about how you could upgrade from the release candidate and wanted to try it. Everything seemed to go fine, until the very final reboot. (Windows was upgraded to the new version). I saw my regular boot menu again, but then windows restarted the machine one last time, and when it came back up it just sat there, nothing happened forever. And Vista won't boot anymore either - I do not even get a boot menu. Just a blank screen with a flashing cursor, and nothing happening....
I tried the repair options, but windows can't find any of my system restore points (I did set a number of them!) neither vista nor 7. From a command prompt I did try to run bcdedit and it shows that my original boot menu should still be there, but the system is unable to find it. I am completely stumped. Can someone please indicate what to do to get my system to boot?
Recently my PC's registry became corrupted, leaving me unable to boot. As I really want to keep my files, programs, settings etc I would much prefer to do an Upgrade install than perform a Custom one and wipe everything.
However, the Windows 7 disk insists I boot into Windows before performing the upgrade installation, which is the one thing I cannot do due to my corrupt registry. Compatibility Report is as follows:
Compatibility Report
The computer started using the Windows installation disk. Remove the installation disk and restart the computer so that Windows starts normally. Then, insert the installation disk and restart the upgrade.
This is a frustrating cycle. I can't boot Windows, so I try to perform an Upgrade Install, which I can't do because I have to boot Windows.
Things I've tried:
- Various chkdsk commands, none of which have worked due to my drive seeming to be write protected
- System restore, which I was unable to do as apparently System Protection must be enabled on the drive and I'm unsurehow to do this
- All of the registry repair tools on Hiren's boot CD, all of which are either irrelevant to the problem or have given me error messages
As I have Hiren's CD I can access my hard drive through Explorer, so would it be possible to use Mini XP to attempt the Upgrade Install? If this isn't possible, how else can I repair my registry?
I have a digital download verson of Windows 7 Pro64 that i am trying to install over my Vista Home premium 32 install. I have burned the contents of the download to a DVD, however when i try to boot to the DVD it says BOOTMGR is missing. The file structure is the same on the 7 DVD as it is on the Vista disk, and both have BOOTMGR on the top of the Disk.I do have hardware that supports 64bit, and i can boot from the Vista CD, so i think the issue is with the burnt 7 Disk.
Gateway GT5636E w/Windows Vista Home Premium 32. Trying to install Microsoft Windows 7 Pro 64. The system is 64 bit compatible and I do have the BIOS set to start DVD optical Drive first and I know I need to do a clean install. Don't go there please.I am using an offical Microsoft install DVD. I place the 64 bit DVD in while Vista is running and shut down as instructions indicate. Upon reboot the system seems to ignore the DVD and reboots to Vista. Also, the 64 bit install disk will not even read in Vista. The 32 bit install disk will read in Vista.
I currently have Vista Ultimate x64 and Windows 7 RC1 x64 running in a dual boot setup. Each OS is installed on a separate disk drive. If I preorder Windows 7 Professional upgrade ($99) will I be able to do a clean install on a partition of my choice or will it force me to clean install over my existing Vista Ultimate partition ?? I understand that I cant do an upgrade in place from Vista Ultimate to Windows 7 Professional. My question is will the preorder Windows 7 upgrade force to me "kill" my Vista Ultimate partition ?
Current state: I have a Dell with Vista HP 64 that hangs alot Near Future State: I fought this problem on my Dell PC / Windows Vista for sometime now and I'm fed up. I'm going to get a iMac and use boot camp to have both Mac OS (Snow Leopard) and Windows 7. Best of both worlds on superior hardware (my and other's opinion, not my point though).Here's my question: I think I'm going to buy Windows 7 Home Premium 64 bit full installation (not upgrade) and use that to "upgrade" my Dell with Vista. Then when I get the iMac, I will use that same product to do a new installation of Windows 7 on the iMac (and decommission the Dell).Is this the right approach? I don't think Windows 7 upgrade will work for the iMac part of the plan. Is this true? Will I be able to "move" Windows 7 full install from Dell to iMac?
My mom's computer started having issues booting a day ago, it seemed like something was draining all of her cpu's power. I verified that was not the case, and ran the computer in safe-mode. I downloaded Ccleaner and cleaned her registry with it (Yes, I verified that the registry values it removed/modified were safe, most of the having to do with programs I know were removed from the computer.) After a re-booting it appears the BCD has gone corruptit would be an easy fix, but her computer, (Bought at the store in a IVY Tech college.) did not come with a windows install disk, so repairing the BCD has proven difficult. Is there any other way I can do it? (I did ensure she made some recovery disk's when she bought it, but as far as I call tell, all they can do is fully restore windows.)
I have downloaded windows 7 home premium upgrade ISO from the microsoft store. The burned the iso to disk using the image burner in windows.
My problem is that the disk will boot, and a "windows is loading" screen appears which only takes a minute. Then a windows background appears on screen with a cursor. That is all. No setup at all. What might be wrong here. I would like to make a bootable disk that works.
I can run setup from an OS, but that is not what I want to be able to do.
I've been trying to install Windows 7 Pro upgrade as dual boot with XP Home, and keep getting the message (something like) "Disk read error - press ctr-alt-del to restart" at the first boot during the installation processHave checked the hard drive for errors, and there are none. Have replaced the hard drive with a brand new one, and get the same result.[I also tried installing Windows 7 Home Premium upgrade, and get the same result.] [code]
I ordered the 50$ Windows 7 upgrade disk. I realize that Windows 7 will need vista or XP already installed for the upgrade version of Windows 7. But if I want to upgrade my Vista 32-bit to Windows 7 64-bit, Will I be able to do it with this upgrade disk? after all I will need a fresh install (because 32 to 64) and this is the upgrade version...
I have a PC with XP Home and wish to upgrade it to Win 7-64. I purchased the Win 7 upgrade version. Will ditch XP when happy with getting programs installed in Win 7.I also have a new drive that I wish to do the install of Win 7.My plan is to hookup new drive, place Win 7 DVD in drive and run the install in Custom mode. This should install Win 7 on new drive and preserve Win XP on the old drive.To register Win 7, I have the serial info from the Win XP system and will insert when asked. I'm concerned about whether this method to register will work correctly as I was told that Win 7 must find a windows.old file on the installation drive. Will it work OK?
im usin 2tb segate new hard disk sir..in my system i cant able to boot my os and also my hard disk...its showin that hard disk boot failure insert system disk press enter ...i restarted many times its sayin the same problem...in my gigabite mobo bios my hard disk is not get detected sir....the problem is that wen im installin the new os for 2nd time its all went nice only sir but at the completion of the os it wil ask for the user name and password but in my system its frozen sir fully of black screen and i cant able to do anythin so i restarted my system from that im gettin this error as hard disk boot failure insert system disk press enter.....that my new hard disk and all of my data is in that hard disk only..this problem arises wen im installing the os for 2nd time sir.
I woke up this morning, and I found that my computer was displaying this message"Disk boot failure, insert system disk and press enter". There are a ton of needed documents on the computer, and I'm hoping that they can be saved some way.
I've been having this error even after reformatting and reinstalling Windows 7 on my desktop. I've done reformatting / reinstalling Windows 7 several times, yet the problem still occurs. I'm thinking of my HDD as being corrupted or messed up. The problem occurred after I accidentally hit the CPU when I was stretching my foot. The screen froze after that. Upon rebooting it, 'Disk boot failure, Insert system disk and press enter' occurs. After I entered the DVD installer of Windows 7, the screen just hangs.
I have been having a bit of trouble with windows 7 lately, namely that it won't start up right. When I boot from the drive normally, it gives me the classic "BOOT DISK ERROR: INSERT SYSTEM DISK AND PRESS ENTER" message.
However, I soon discovered that if I boot from the Windows 7 cd and do not boot from it (By ignoring the "Press a key to boot from CD or DVD..." Windows 7 boots up fine. I've tweaked my BIOS over and over, but the same problem persists. The drive is brand new and fine. What can I do?
My friend bought a new PC and needed to put am OS on it. He put in the W7 disk and the error message 'disk boot failure insert system disk and press enter' appeared before installation was shown. He has tried changing around BIOS and it also recognises the hard drive and DVD/ CD ROM drive. Here is the specification he was given:Case : CIT Reaper Black Mesh fronted Tower CaseMotherboard : Gigabyte 78LMT Motherboard TechnologyCPU : AMD Bulldozer FX 4170 4.2ghz 8mb CacheHard Drive : 1tb Sata Hard DriveMemory : 8gb DDR3 1600mhz MemoryOptical Drive : 24x Dual Layer Sata DVD WriterGraphics Card : Nvidia Geforce GTX 650 2gb GDDR5 With HDMIPower Supply : 750 Watt Branded Power Supply Also, he has tried booting BIOS in different order
When starting the computer, I keep getting "Disk boot failure, insert system disk and press enter". Nothing works other than putting in the boot disk and hitting the restart button on the tower. Then it will boot up and run fine. But how do I stop it from having to have the disk in order to load? Checked in the BIOS and the hard drive is the first load.