System Reboots Safe Mode Option Screen
Jun 21, 2008
I have done a clean install of Vista Ultimate (64), and since then, everytime I start my computer, it fails to boot correctly. It passes the BIOS page, starts the animated bar at the bottom of the page, and a few seconds later, the screen goes blank, and my VDU gives the messgae, "NO SIGNAL" After about a minute, the system reboots to the BIOS page again and continues up to the animated screen, and stops again. After it self boots for a second time, I get the SAFE MODE option screen. If I leave it on START WINDOWS NORMALLY, and leave it to complete the 30s count down, It boots again, and then completes the boot into Vista. If at the count down screen, I press enter, it goes into a boot loop that doesn't stop until I press the reset button on my box.? I have done a re-install twice and problem continues.
View 8 Replies
ADVERTISEMENT
May 6, 2008
I've been trying for 2 days now to upgrade from Vista Business edition to SP1. The same thing keeps happening. I get through parts 1 and 2 ok, but when the system reboots for part 3, it reboots several times giving me the choice to boot normally or in safe mode, then eventually it stops rebooting and just goes blank. I can reboot successfully in safe mode but the installation of part 3 will ultimately fail (the error code points to not being able to install particular components as a result of being in safe mode) and the system has to regress to the original condition. I tried all the suggestions on the MS Vista upgrade trouble shooting site (as well as several other sites)- including checking for specific updates - none of which apply to my machine - at least that what windows update tells me when I try to install them, checked the disk for errors, and checked the memory for problems. I also turned absolutely everything no- original MS off for start up including antivirus and some other stuff that I have and the same thing keeps happening. Each pass, from upgrade install to fail, and regress back to original condition takes about 5 hours.
I'm running Vista on a quad core machine with 4G of onboard memory (even though Vista 32 can only use about 3 gigs) and a smoking video card so I doubt this is a hardware problem. This problem appears to be similar to the original 'endless reboot' problem that prompted the original halting of SP1 distribution back in the early spring - I thought that problem was fixed! I tried to get real time help from the MS site but got a message that there was a problem with the site. - Good Greif! This is probably the most frustrating MS experience of all time. With all due respect to the folks at MS, if it was your intention to have people to switch from Windows PC's to Apples or even Linux based PC's, I doubt you could have come up with a better plan. I've already switched two of my home computers to Ubutu!
View 8 Replies
View Related
Mar 26, 2008
i bought a 64 bit version of vista and i have built a new system with an asus p5e mobo 4gb of ram 8800 gt graphics and everything shows to install at the complete installation time it reboots and it then tells me windows did not shut down properly and and give me the safe mode option or boot windows normally when i hit safe mode it says it cannot boot into safe mode and when i hit boot normally it says the computer restarted unexpectedly or encountered an unexpected problem and cannot proceed. to install press ok to restart and start the whole installation process over again.
View 4 Replies
View Related
Apr 17, 2009
Vista installed fine and everything works fine until, a piece of software asked to restart. Now I have to hope that is boots. Because when it the boot process reaches the microsoft corporation and finishes, the system gives a blank screen and hangs. If I wait long enough, 15+ minutes, it finally boots with the vista logo on the second screen and logon password on the first screen. This is a new pc, just built, I should not have this problem. The pc has an integrated nvidia 9400 with 9800gt. Can it be a grahics card problem? I used the cd to install the drivers that came with the 9800gt.
View 6 Replies
View Related
Mar 23, 2008
downloaded and installed vista SP 1 for vista Ultimate (64), upon restarting system, goes to system dump screen (blue screen) while loading windows. Can only start in safe mode, used system restore to fix. Tried reinstalling, same problem.
View 4 Replies
View Related
Sep 29, 2009
I have a laptop that I'm looking at that will automatically boot into safe mode. I've restored the system from the earliest possible restore point but that did not resolve the problem. The only clue that I can find as to the cause is the following event from the system event log. Event 7026, Service control manager eventlog provider. The following boot-start or system-start driver(s) failed to load: spldr Wanarpv6. is that this is the cause of the safe mode but cannot find any solutions to the issue.
View 6 Replies
View Related
Mar 23, 2008
I'm getting a BSOD right when Vista gets to the login screen on startup. The system will boot to safe mode, but I have no idea how to fix it from there. This happened suddenly on a system that has been running stable for 6+ months. At first I thought that perhaps some of my RAM was bad, so I tried booting with just one stick in (I have 4x1gb), but it wouldn't boot on any of them. My other suspicion was that I had installed drivers for a new keyboard that night before (as that was the only recent change to my system configuration), so I deleted those, but that didn't help either. I'm thinking my next move is to flash my BIOS, but I'm running out of ideas......
View 4 Replies
View Related
Apr 8, 2009
I've got this major bluescreen issue. Two days ago, I just restarted my pc for no particular reason, and when it was about to start it gives me this bluescreen. It starts up, I get the loading bar, but then bluescreen. I tried to chose any of the safe modes, but none of them work, just gives me the bluescreen again. To sum all this, I can?t start my computer due to a bluescreen issue, not even with safemodes. It gives me alot of text, but the screen dissappears after a few seconds so I can?t even read two lines. I'm running a HP Pavilion m8055.sc with Windows Vista Home Premium 32bit
View 9 Replies
View Related
Aug 30, 2009
my sony laptop ( vgn-fz70b ) shutdown with no reason, all of a sudden when i try to restart i saw a blue screen of death and afterwards it shutdown and restart again.i try to press f8 to open in safe mode and to check what is the problem but unfortunately i cant access to safemode.i try to reinstall again the os but when i am in the part that choosing the drive i didnt see any drive. and < click load driver to provide a mass storage driver for installation >.i stop downloading cause i cant see any harddisk on their.and i check bios setup..
boot priority order:
1:usb optical drive (*)
2:internal optical drive
3:floppy disk drive(*)
4:usb flash (*)
5:usb hard disk drive (*)
6:internal hard disk drive
7:network
there is no change values for all of these which supposed to be is to set them who is 1st,2nd,3rd. *-means this drive is available when external device boot is enable.
View 6 Replies
View Related
Sep 26, 2009
i have installed litestep, didn't like it, so i pressed uninstall. nothin happened.i decided to reboot, did so, and when i log in, it shows My Computer in explorer! i thought it was just meant to be the desktop starting, not explorer. and there wsa also no taskbar anywhere. i pressed the windows button, nothin happening. anyway i tried safe mode, in which i noticed there was an exe file starting with the core drivers. that must be what is left of litestep.
View 7 Replies
View Related
Jan 30, 2010
I am trying to use a system restore disk for my friend's computer that I downloaded. The computer have Vista, now I have a 32 bit and 64 bit disc. How can I find out which version of Vista I have? I cannot boot into window or safe mode ( I could figure it out from there). I also tried to check the Bios and saw nothing. The laptop only has 2 gigs of RAM I think, so I would assume 32 Bit, but I want to be sure. Also, if I used the wrong one, would it mess up the computer? or could I just redo it with the other CD?
View 5 Replies
View Related
Aug 12, 2009
System would only boot up in safe mode, now there is a "unmountable boot volume" 0x000000ED. I just want the pictures off that drive. how should I get them if the operating system doesn't work? Can i plug the SATA drive into my Vista machine?
View 5 Replies
View Related
Feb 1, 2010
I am trying to fix a laptop.. it is getting blue screen.. things i did
1. Replace ram
2. Tried booting on safe mode/ last good configuration both didn't work
When I put a windows cd for repair (windows XP Home) and boot from cd.. its goes on the window where I need to select 1.c:windows but when i select that.. it goes on blue screen again.. I removed the hard disk.. connect it externally and ran a chkdsk /r and chkdsk /f then put it back to the laptop still didnt work..
View 9 Replies
View Related
Nov 29, 2009
My friend at work forgot his password and cannot log onto his computer. He is running Windows vista home premium on a Compaq laptop. We tried to go into the safe mode but the only screen we get is his password sign on screen. Even during boot we pressed f8 key but the password screen came up. He is hoping someone has an idea or answer so he can avoid taking it into get looked at and paying money.
View 9 Replies
View Related
Oct 12, 2009
Using my ISP (Roadrunner Carolinas) speed test site; I get around 200 to 400 kbps download speeds using IE in normal mode. If I boot to Safe Mode, I get around 3500 to 4500 kbps, which is what it should be (this is what I used to get in normal mode before I re-installed Vista). Running the same speed test with Firefox, I get around 1500 to 2000 kbps in normal mode, but if I try to download a file it ransfers at only the 200 to 400 kbsp rate (if I'm lucky). Here's more detail about the system and what I've done so far:
Installed all updates including SP2.
Using Windows Firewall, no anti-virus.
Updated network drivers directly from NVidia (Chipset is nForce750i)
Updated graphics card drivers directly from NVidia
Disabled all LAN protocols except for Client for Microsoft Networks and IPv4
Connected via ethernet cable directly to cable modem, no router.
I've deliberately refrained from loading anything but the basics until I can get this sorted out..........
View 7 Replies
View Related
Jun 5, 2009
i have both Vista and XP in my system with Vista in C drive and XP in D drive..i want to work in full screen mode of XP.. but in vista i cant do it...So each time i have to reboot my sytem and get into XP to do so..so if i can load already installed XP on my vista, it would be helpful...can anyone help me out..remember that i have installed XP and Vista already and i am not using any Virtual PC kind.
View 6 Replies
View Related
Nov 2, 2009
I had my accounting software running which I minimized. I went out for a couple of hours and found out that my computer had reboot automatically as the minimized program was no longer in the task bar. I am running Norton Internet Security 2009, and Iolo's system mechanics 9.0. Only Norton is active. The other one I run it as I like. I also scan my
system with Malwarebytes frequently. Malwarebytes always finds two infections which are "Broken Open Command - notebook bad (%1) good (%1). Even after it is cleared, it comes back.I have tried to convey as much information as possible. My operating
system is Vista Home Premium 32bt.
View 9 Replies
View Related
Jan 29, 2009
About a week ago a strange new problem started. I have a Toshiba laptop with Vista Home and dual core processor. Lately on SOME occasions the computer reboots itself when I close the lid. It does not do it every time and will shut down fine every time normally. But on some shut downs, when I close the lid the system reboots. It might do this a couple of times in a row and it might not do it for 3 or 4 shut downs. I use the shut down from the start menu. I have changed all of the setting for power settings and what to do when the lid is shut to either never or do nothing and it does not affect it. This computer is only about 4 months old. I have done a restore point before this started but no help.
View 5 Replies
View Related
Feb 12, 2010
Windows Vista Home Premium on an Acer 4420 laptop was working fine up until Wednesday morning. I installed about a dozen updates and ever since then I've had the computer crash randomly but regularly when I have IE8 open. I get a fairly quick blue screen message and then the system reboots without anyone telling it to. If I simply have the computer running but do not have IE8 running it seems to stay stable. I've uninstalled all the updates but it hasn't made any difference--still crashing!
View 6 Replies
View Related
Nov 22, 2009
I have Vista Home Premium x32 with SP2 installed running on an Intel motherboard Core2 Quad with 3GB memory and a nvida 8800GT video board and a 400 Watt p/s, 500GB drive with plenty of free space. My system fan speeds up to full speed and then re-boots. The only warning I get is the fan noise. This happens 5 or 6 times then it won't happen again for a couple days. It seems to happen exactly 1 hour from the last time it rebooted.... no kidding, within a couple seconds of 60 minutes.
Anyway, I thought I would check the event logs for a clue. I noticed that the Shutdown Event Tracker was not available so I looked for a way to turn it on. Vista, at least my version, does not have the gpedit.msc (Group policy console editor?) and other articles indicated that is what I needed to activate the Tracker.
The only thing I can find in the other logs is a recurring entry: "The DgiVecp service failed to start due to the following error: The system cannot find the device specified." how to enable the Shutdown Event Tracker?
View 7 Replies
View Related
Mar 23, 2008
I've tried and tried, please I hope you can help me. I have a Toshiba A215-4817 laptop with Vista Home Premium 32bit. My troubles began when my cd/dvd was not operating properly. Toshiba support said my operating system was corrupt. I didn't believe that just because the cd/dvd wasn't working properly that the os is corrupt, maybe they were right.
I have extremely important info on my hd as I do taxes for a living.
In an effort to trouble shoot the cd/dvd I booted into safe mode. No-one tole me that the administrator account is disabled by default! So now I can't get out of safe mode. I have access to only my limited user account and uac is enabled. System restore doesn't change boot options.
I can't edit registry = access denied, cmd.exe when trying to activate administrator account = system error 5.
View 9 Replies
View Related
May 12, 2009
i'm on windows vista and i can't get out of safe mode does anyone know how to x
View 9 Replies
View Related
Jun 26, 2008
My son kept shutting the laptop w/o powering down and now it starts in safe mode. The first time I rebooted and this solved the problem but now that won't work. I can't get it to go back to normal. This has happened in the past but I can't remember what I did to fix it.
View 9 Replies
View Related
Mar 23, 2008
I had an issue with one of my games and it directed me to go into safe mode to uninstall it. Now that it's uninstalled, I can't get out of safe mode. I've been through this forum in and out. I've done nearly all the things that it has stated that come close to my issue. I'm still in here. I've been in and out for 3 hours now. I've gone through the msconfig, and told it to restart in normal mode, I'm still in safe mode. I've used the F8 button while starting it, and told it to go to safe mode, I'm still here. I've even checked to see if it was the resolution, I've set it to my default settings of 1280x720, and restart it, it's still in safe mode. I've done EVERYTHING that I can think of.
View 6 Replies
View Related
Jan 7, 2010
I am having a strange problem with my Windows Vista Home Premium installation. The login screen loads and I can write the user and password boxes, but when I insert the password for my user and I hit the enter button or click the arrow button it does nothing. Clicking on shutdown options button does nothing. Pressing ctrl+alt+del does nothing. And after about 30 seconds it reboots and all the same happen endlessly. I tried all the recovery options ( boot in safe mode, last working configuration, disable restart at error, etc... ) and all have the same behavior.
I booted with the Windows Vista Recovery Tools from the DVD and I used chkdsk. It says that found errors and corrected them but when I run again the chkdsk the same errors are reported and corrected. Used sfc /scannow with the offline options and it says that found some corrupted files and is unable to correct them, but when I check the logs no relevant errors are found. Tested the memory and the hard drive using ubuntu live cd and the results were that both are ok. With ubuntu live cd I am able to boot and access all the windows files.
This is not the error "installing updates 3 of 3" or the black screen of death after welcome screen. This happened when I was using the pc and suddenly it freezed and I pressed the power button to do a hard shutdown. After that these symptoms started. Until there everything was fine. I didn't download any virus, as I am a computer programmer and I know what I am doing I just can't understand this error. What do you guys think it is? Is it a virus or some of the system files are corrupted or a hardware problem? I would not like the reinstall vista option because I have a lot of data and a lot of programs installed. What other options do I have? By the way the Vista I have is Service Pack 2.
View 4 Replies
View Related
Apr 24, 2008
I press f5 or is it f8. but either way I get to the Safe Mood Selection screen and no matter what option I select, Safe Mode or Safe Mode with Prompts, of Safe Mood with Network support, it doesn't matter it boots normal to my user sign in screen and then it freezes.. no mouse or keyboard functions... If I run the recovery disk and tool options then mouse and keyboard work but I still cannot boot up in safe mode nor can I boot up normal.. I just need to get into safe mode and then I believe I can resolve this but since I can't get into safe mode I don't know what else to do?
View 9 Replies
View Related
Nov 14, 2009
I had trend doing a new scan a more complete one while it was doing it i went in i could stop it hit cancel stop safe box and computer wouldreturn to normal I thought that was 6 hourds ago well after i deletedtrend it still in a safe mode.
View 9 Replies
View Related
Nov 14, 2009
I can say is I changed trend to do a real good cleaning of all of folders etc. When I got the safe mode I found trend was doinmg a scan so I stopped it and then it said close and stop safe mode which I did. I also deleted trend to. I m really bad I dont know what I did. I use that I had brain surgery and I m just dah sometimes.
View 5 Replies
View Related
Mar 23, 2008
I have a new motherboard (abit nh-m2sv), X2 +3800 processor, 2 gig pc4200 memory ATI graphics, DVD RW, Maxtor SATA drive, all are suppose to be Vista ready, but vista either won't install, or installs with BSOD's then will only run in Safe Mode.
I have tried Home Basic and premium, the same issue, I install my old faitful XP and it goes straight in. I have run memtest, all fine, I have removed the gfx card, no change, I have tried an IDE hdd rather than a SATA no change.
View 6 Replies
View Related
Jan 19, 2010
Vista will not boot into Safe mode or Normally. The mouse pointer sits on the screen and can be moved but the logon screen does not appear. When I go into startup repair it says it "Could not detect a problem". I have run a chkdsk /f which ran clean. What else can I try to make the logon screen appear?
View 5 Replies
View Related
Sep 8, 2009
I?m have a troubling issue with my computer as it is stuck on a cycle boot when it passes the windows loading screen and then it simply restarts and does a POST test again. I tried pushing F8 key and selecting all the options
safe mode
safe mode with command prompt
safe mode with networking
Go to last working configuration (advanced)
Start Windows Normally ect....
but as I selected safe mode all the windows emergency drivers are loading then the screen go black and repeats the same problem above. I don?t have a cdrom neither an fdd only a usb flash drive.
View 8 Replies
View Related
