Software RAID0 Fails To Initialize After Reboot
Mar 26, 2008
I've looked over whole internet, and I am very surprised to be unable to find any answers to this. I am setting up Windows Dynamic Striped (RAID0) or Spanned volume (GPT) over four SATA hard drives 1Tb each. Everything is successful. I format the drive, copy stuff on to it, read it back, its fast, very nice. Then I reboot. After boot up I foind out that my D: drive is gone, i.e., volume is offline (as reported by Disk Manager). I can boot as I am using separate (IDE or SATA) hard drive to boot the Vista from. Now, if I configure the striped volume to be less then 2Tb (e.g., stripe two 1Tb disks or four x 500Mb partition each), everything works fine. I reboot and the volume is still there running happily.
View 4 Replies
ADVERTISEMENT
Mar 23, 2008
I've looked over whole internet, and I am very surprised to be unable to find any answers to this. I am setting up Windows Dynamic Striped (RAID0) or Spanned volume (GPT) over four SATA hard drives 1Tb each. Everything is successful. I format the drive, copy stuff on to it, read it back, its fast, very nice. Then I reboot. After boot up I foind out that my D: drive is gone, i.e., volume is offline (as reported by Disk Manager). I can boot as I am using separate (IDE or SATA) hard drive to boot the Vista from. Now, if I configure the striped volume to be less then 2Tb (e.g., stripe two 1Tb disks or four x 500Mb partition each), everything works fine. I reboot and the volume is still there running happily. No windows event log I can find corresponds to this problem.......
View 4 Replies
View Related
Nov 24, 2009
Made image of disk using Macrium Reflect Restart and setup Raid in Bios, then using ctrl-i, use Intel Matrix Storage RAID to make Raid0. Then using Reflect I restore the image. But when I then reboot I get a very fast BSOD and Vista won't boot. In safe mode it seems to lock when loading crcdisk.sys. After doing alot of research it seems that I may need Raid drivers. So question is how can I instal the Raid drivers without losing all my data? I don't want to reinstall windows.
View 4 Replies
View Related
Mar 23, 2008
Is there a way to use the upgrade ability of Vista to upgrade xp pro to Vista Business without having to do a fresh install?
View 4 Replies
View Related
May 15, 2008
Vista 64 Home Premium.
Where is the tab/command to initialize (fdisk?) a new HDD?
I am logged in as Administrator (system says so) with full control/permission.
I can see the hard drives in the Device Manager/Disk Drives. All drives are "good" per the controller and I can see them as physical devices on the computer.
They all show as "Not Initialized" when I ask each to opopulate the Volumes info, and there is no obvious/apparent way to do it. Nothing on the controller shows it either.
Tried "Simple New Volume" under Disk Management--
doesn't/won't work because drive is not initialized.
One drive = one big partition = one drive letter.
View 9 Replies
View Related
Jul 20, 2009
I recently got Halo 2,and before I had I had ran a test and it said I met the minimum requirements. When I tried to install it however, it would change my resolution to 800 x 600, the display the message-(Initialization failed.Either insufficient system resources were found to run the game or game data is missing or damaged.Reinstalling the game may fix this problem. When I also try to customize game install,it tells me-Installation cannot be customized after game installation is initialized. I looked at some other threads and tried to update my graphics driver,but it said I had a custom driver installed and trying to install another driver may damage it.
View 6 Replies
View Related
Jun 9, 2008
HP Desktop (1 year old) Vista Home Premium 32 bit SP1. Had AVG 7.5 for about six months (with email scan disabled). AVG offerred Version 8 and I allowed it to download and install. Big mistake!! Gave me nothing but trouble. When I tried to uninstall it, I realized it wasn't listed in Install/Uninstall. But I saw that AVG had an Uninstall as part of their program....so I used it. (My second mistake!)
Now, whenever I start up.....a window appears: "AVG Anti-Virus System. Could not initialize AVG Anti-Virus kernel interface." How can I get rid of this window? It doesn't cause trouble...but I hate seeing it everytime I start the computer. As you can guess...I'm not a Guru...just a user..so please try to keep it simple...if possible.
View 4 Replies
View Related
Aug 1, 2009
I recently purchased an new HP with Windows Vista 64bit. I can download the Acrosslite but Windows will not initialize the program.
I get this message:
Could not initialize installation. File size expected 1316988 size retunrned 349692.
View 5 Replies
View Related
Mar 28, 2010
I'm trying to play Age of Empires II in my bro's netbook, but I get an odd message "Could not initialize graphics system. Make sure that your video card and driver are compatible with DirectDraw". Though, I've been searching, and it seems that it's not really an odd problem, looks quite popular. I even read some threads on this forum, but none of them had solutions that were still available.
View 4 Replies
View Related
Jun 19, 2009
I'm trying to install either Firefox or Flock and I get the following error: Quote: Could not initialize the application's security component. The most likely cause is problems with files in your application's profile directory. Please check that this directory has no read/write restrictions and your hard disk is not full or close to full. It is recommended that you exit the application and fix the problem. If you continue to use this session, you might see incorrect application behaviour when accessing security features. I click "OK" and the program does open with, as it says, incorrect behaviour.
View 4 Replies
View Related
Mar 26, 2008
When attempting to install Tax Cut State program a message comes up "TaxCutAZ.exe" application failed to initalize properly (0xc0000005) The program then terminates. Still can not get the program to load.
View 4 Replies
View Related
Apr 26, 2008
I have a HP Mefia Center that came with XP preloaded and I made recovery disks. They also offered Vista free. I got the Vista and it came with "Upgrade Assistant" I ignored the assistant expecting it was more PR crap. I installed the Vista and it worked ok but I saw that XP was better. The installation did not give any option other than "clean install". After trying to install an old program that failed I started have problems with failed initializing programs including IE7. I was getting data execution prevention errors. On startup I get; Application failed to initialize 0x00000005. A problem caused program to stop working.
View 4 Replies
View Related
Mar 17, 2010
Cannot open any *.exe files to include browsers. I have tried to do a system restore, but did not help. I have also tried everything in safe mode with no luck.
I have tried to run hijackthis, but it won't run either.
View 9 Replies
View Related
Dec 26, 2009
i have tried everything said in this thread & i still cant initialize the HDD. i get this error:- This request could not be performed because of an I/O device error.
i really need to get access to my drive as it has important files i really need
View 9 Replies
View Related
Apr 11, 2009
I receive the following message when I have logged on to my computer: Windows Defender "Application failed to initialize: 0x800106ba. A problem caused this service to stop." I have looked at Help and Support but have not found anything to identify what the problem is. I run Vista Home Premium 64 Bit OS.
View 6 Replies
View Related
Mar 23, 2008
When attempting to install Tax Cut State program a message comes up "TaxCutAZ.exe" application failed to initalize properly (0xc0000005) The program then terminates. Still can not get the program to load. how to correct this problem?
View 4 Replies
View Related
Jun 13, 2009
I get a message saying evertime I try to start it, saying
that the application failed to initialize 0x800106ba. a problem caused this program's service to stop.to start the service, restart your computer or search help and support.
View 3 Replies
View Related
Apr 8, 2009
I got this error message after I turn off Windows defender via GPO in AD on a Vista PC: windows defender application failed to initialize 0x800106ba? I am looking for solution for the error.
Scenario:
AD 2003
Vista enterprise installation
Office 2007 installed
McAfee installed
McAfee firewall is installed
Windows defender can be turned off
Disabling the Windows defender GPO results in the error after rebooting the system: windows defender application failed to initialize 0x800106ba?
View 8 Replies
View Related
Mar 23, 2008
I just downloaded a bunch of application and did a lot of work on my computer. I do however, have samantic endpoint virus protection and did a couple of scans with no problems. When i try to open windows defender i am getting an error that says. Application failed to initialize: 0 x 800106ba. A problem caused this program's service to stop. To start the service restart your computer or search Help and Support for how to start a service manually. I restarted and tried to open it but got the same error.
View 9 Replies
View Related
Jul 5, 2008
I have the following issue and hope that somebody can give me a hint about what might be going on! My system has two raid 1 arrays - one is running on XP Professional SP3 the other one is running on Vista x64 Ultimate SP1. When I start my virtual machines (either from the Virtual PC console or when double-clicking the *.vmc files) than everything is working fine on XP and the virtual machines are booting and running as expected. However, on Vista the following is happening (and I hope somebody has an idea):
1. Starting the Virtual machines from the console leads to an immediate reboot of my host machine (I can't even see any boot screen of the virtual machine - it is like clicking start in the VPC console -- > reboot of host).
Now I tried the following:.........
View 9 Replies
View Related
Feb 16, 2009
This message kept coming up after I turned my computer on. What does this mean and what do I need to do to fix this?? "Application failed to initialize 0x80016ba." A problem caused this program's service to stop. To start the service, restart your computer or search Help and Support for how to start a service manually."
View 9 Replies
View Related
Mar 4, 2009
My daughter suddenly experiences: Windows Defender: "Error Code 0x800106ba Application failed to initialize" This is a fairly new machine (running Vista Home Premium) and it was delivered with McAfee virus protection installed. The initial McAfee license is about to expire so she renewed that license for a permanent licence today. There may of course be a connection here, but I fail to see what that connection could be.
She was guided to http://support.microsoft.com/kb/931849 which suggests to initially remove (uninstall) Windows Defender and then reinstall it. The only problem with this is that Windows Defender is not included in the list of installed programs that can be uninstalled, and when she tries to "reinstall" it Windows Defender is reported as already present on the system. I checked on my own system where Windows Defender is running without any problem, and the same applies here: Windows Defender is not listed among installed programs.
View 9 Replies
View Related
Apr 14, 2008
so im not a computer expert and I just got my computer a few months ago. Recently I donloaded Skype 3.6, but i never knew it wasn't for Vista, so it messed my computer up. I deleted it, but now my right click dosnt work, only my touchpad and my computer it 100x slower. Someone told me i should just reboot my computer, but no matter what i try it dosnt reboot, any idea's on how to reboot??
View 4 Replies
View Related
May 3, 2008
I have had this issue for many months, now. I loaded Vista x64 Home Premium to run in a dual-boot configuration with my XP Pro. I do critical work so I didn't trust going to Vista exclusively. I mainly wanted it to see if I could utilize all my RAM and speed up Photoshop processing. I have had it working three or four times, (except for tablet functionality) then when I must re-boot because of SP1 and other security updates or in one case, I installed Office 2007, it does nothing on restart; black screens and just sits there, totally unresponsive.
No blinking of the LED which shows drive activity. When re-booting, F8 isn't working (nothing happens). Regarding the previous instances, I gave up trying to get it to respond and went back to booting into XP, which always works fine. Then after a period (usually a month or more) I will try booting into Vista, on restart, and viola, it works again! WTF is going on?
View 8 Replies
View Related
Oct 16, 2008
Occasionally when I've been away from the computer for a short time and it goes into sleep mode (it`s set for 15 minutes), I can't bring up the display simply by hitting a key. I have to shut it down and restart. The boot button on the console will still be lit and I have to shut it down before I reboot. This probably happens about 30% of the time. The other 70% it comes back up with a key touch.
View 6 Replies
View Related
Jun 21, 2008
I used to have Windows XP on this PC and I have recently replaced it with a clean install of Windows Vista Ultimate 32 bit. Since then my computer will no longer reboot. When I click start > restart it will shut down like it should, then it will go to the POST screen and from there it goes black and nothing happens (where it would normally load windows). I have taken out my C: drive and put it in another PC and it worked perfectly. I have a C and D drive which are both 2 separate hard disks and always worked fine in XP. How can I fix this? They are both IDE. I have to now power off the PC and power it on again to restart.
View 4 Replies
View Related
Mar 23, 2008
I received this after my computer locked up when trying to open up windows Mail "Windows Mail could not be started, initialize junk filtering. Your computer may be out of memory or your disk is full. (0x80070002)" After closing that error out I get "Windows Mail could not be started because MSOE.DLL could not be initialized.
View 9 Replies
View Related
Apr 8, 2010
When I try to boot windows I get the black Windows Error Recovery screen with the options to Launch Startup Repair or Start Windows Normally. If I select start windows normally the systems quickly restarts and takes me right back to that screen. If I select Startup Repair, I get the blue screen of death, "A problem has been detected and Windows has been shut down to prevent damage to your computer". Even trying to use the boot options, launching startup repair still gets the blue screen, safe mode still just restarts and takes me back to the beginning. All of this started sometime last night when the computer must have installed updates and then tried to restart itself because I walked out this morning to the blue screen. Any suggestions? I do not have any sort of disk for the computer, its an HP. I am writing this from another computer, as I obviously cannot make the problem computer start at all.
View 9 Replies
View Related
Jun 18, 2008
I just installed Vista x64 and found it failed to connect to my home network. Diagnostic indicates the Vista is failing to get IP from the router. This did not happen when I installed Vista x86 or XP x86, x64. Other machine running these OSes have no connection problem. What could be wrong with the Vista x64?
View 9 Replies
View Related
Apr 1, 2008
Until several months ago, I was able to scan in Vista Ultimate (SP1). Recently, however, when I start WFS.exe, nothing happens at all. I don't see the application in my task list or on the screen.
View 9 Replies
View Related
Mar 21, 2008
trustedinstaller.exe crashs. All pre-SP1 updates are installed. Using Vista Ultimate x64.
View 7 Replies
View Related
