Easy Transfer Autoloads On XP Machine
May 9, 2008
I asked the following question in the XP help and support NG, but they told me to come here instead. I transferred what files I needed from my older XP PC to a new Vista machine. Now whenever I boot up my XP PC, the XP PC opens up a folder onto the desktop called "Microsoft" which has another folder in it called "MigWiz". I can click it closed, but it is a pain to have to do every time I turn that computer on. I tried to locate the program name running msconfig.exe, but could not findit in particular. I also went to "Add/Remove Programs...", found the program, but said that certain other programs I have would/could possibly not run right if I removed the Easy Transfer application...one of which is UPnP. Is there another way to remove the Easy transfer program? Perhaps reverting to an earlier system restore point?
View 4 Replies
ADVERTISEMENT
Jun 15, 2008
I am attempting to transfer files & settings using the Belkin Easy Transfer cable from an XP computer to a Vista computer. All starts well by showing that the two computers are connected. But after finding the files and settings and providing the amount of data to be transferred, it starts gathering information but then shows a flashing disconnection icon in the upper right of both computers' transfer windows and freezes. This happens at a different place each time, but early in the procedure (after about 10 minutes). Would anyone have any advice? I have done everything by the book, as far as I'm aware.
View 7 Replies
View Related
Jan 5, 2009
the instructions for both the cable and Windows Easy Transfer program are practically non-existant. The directions for the cable said to install the software onto the XP machine (easy enough), and then connect the two computers with the cable, again, very simple. Then I was to follow the on screen instructions.
Instructions were as follows: "Windows automatically detects the connection". That's it, no buttons to click, nothing to type in, no load screen, no scan, nothing. So I waited... and waited... and waited. Nothing happened. So I unhooked the cable, disconnected both computers from the internet, disabled any and all firewalls, spyware software, antivirus software, anything that could possibly interfere with the connection. And I tried again... and again... and again. Not Happy, not simple, not easy! Am I doing something wrong? Did I miss a step? Or is Vista really the problem everyone has been proclaiming it?
View 4 Replies
View Related
Jun 28, 2008
I'm running Vista Home Premium on a 2 month old HP. There are 3 harddrives --- the original one from HP, the old one from my old computer(both internal), and a drive that is external, connected via USB, thatI use to hold my backup disk image files.For a few weeks, no problem. Lately, every time I double click on theexternal drive in Windows Explorer, Windows Easy Transfer startsrunning. If I right-click instead and then click on "Open", there'sno problem (Easy Transfer does not open). Any ideas on how to stop this unwanted loading of Easy Transfer?
View 9 Replies
View Related
Mar 23, 2008
I want to use 'Windows Easy Transfer' wizard to transfer solely emails and contacts from XP OE6 to Vista Home.
a) Can I pick this alone, with the wizard ?
b) If Yes, How ? -- I don't find a choice to transfer only emails and address book.
c) If No, what is the alternative ?
View 9 Replies
View Related
Mar 30, 2008
I bought a new Vista laptop about 3 months ago and have only got around to transferring stuff from my old XP pc just now. I decided to use Windows Easy Transfer and for the most part it was easy except for Outlook. It seems to have replaced my existing Outlook 2003 OST files with those from my old pc (also Outlook 2003) - does this mean that I have lost the last 3 months of emails or is the file I am missing been transferred somewhere that I can't see anymore. When I try to access local settings the UAC tells me that I don't have permission?
View 5 Replies
View Related
Jun 13, 2009
I have gone back to Vista after using Win 7. I used Windows Easy Transfer (WET)and loaded up an external drive. I found that Vista SP2 seems to have a slightly different WET gui and have not been able to xfer any data at all. I can get to the point of selecting path and password but then cannot get a path that the Vista version of WET will recongnize even though it shows up and can be selected the WET that is on the external drive. Went back to Vista to get ready for the release of the retail version of 7 and did not want to mess with the RC and eventual clean install next year.
View 7 Replies
View Related
Apr 19, 2008
I bought my wife a new Vista Home Premium notebook to replace her old XP one. When I used the Easy Transfer prg and the Companion, everything worked EXCEPT that her profile from the XP machine was created on the Vista one. By that I mean the Admin Profile on the XP was Nancy. The Admin on the Vista one was also named Nancy. Yet when the Easy Transfer happened, it created a second Nancy profile. One that had what I wanted to be in th enew one's Admin profile.
View 5 Replies
View Related
May 21, 2008
When I use Windows Easy Transfer am I removing the files from the old computer and putting them on the new one? Or am I just copying the files on the old and putting new copies on the new computer?
View 6 Replies
View Related
Mar 26, 2008
Will Windows Easy Transfer work with only XP? I'm getting a new laptop before my old one stops working and I don't want to move to Vista. I just want to move XP pro to XP pro.
View 6 Replies
View Related
Apr 9, 2008
I am trying to use Windows Easy Transfer to transfer documents and settings from a Window XP machine to a new Vista Professional machine. I am trying to do this over our network (SBS2003 if that's relevant). Windows Easy Transfer seems to be working fine to a point, but then it gets stuck on a particular file (on the XP machine) and doesn't continue. A flashing icon appears near the top right, but there are no options to skip a file or anything like that. I have tried deleting what I believed was the offending file, only to have WET stop on a different file. If there was a way to skip a problem file, that would be great, but the only time I see a prompt suggesting that I can do that is after I have already cancelled the transfer (on the XP machine).
View 4 Replies
View Related
Jun 24, 2009
i recently bought a new computer, its running Vista (64 bit) Home Premium, and when i first got it i attempted to do an "Easy Transfer" from my old laptop to this new desktop (the laptop was running Vista Home Premium ((32 bit i believe)), not sure if this may have anything to do with the problem)... but anyway, after the Easy Transfer was done, after shutting off my pc and restarting it, upon the windows startup screen the message "incorrect password" pops up first thing before i even try to type in any password o.O ... my pc is secured with a password and if i click ok and then type in the password it works fine, but at start up now every single time the first thing i see is "incorrect password" regardless of the fact that i havnt tried typing in the password yet, and like i said, if i just click ok and type in the password it works fine, so this problem hasnt really been bothering me that much, but i do find it quite odd and was wondering if anyone knew what this could be caused from (its the least of my problems with Vista 64 bit so far btw -_-) .... but yea, ive never seen a vista system show the "incorrect password" message before you even attempt to type the password in at startup haha...
View 4 Replies
View Related
Jul 29, 2009
1. On my old laptop (Windows XP) I first used MS Office 2003, I then installed MS Office 2007 Student and Home. Before uninstalling Office 2003 I stored some Outlook pst-files (e-mail, contacts and archive files). How can I import these files into Windows Mail/Contacts on my new laptop (Windows Vista/MS Office 2007 H&S). I tried Windows Easy Transfer, but it didn't work.
2. How can I import Mozilla Thunderbird files (e-mail, contacts) from the old laptop into Windows Mail/Contacts on the new one? The wizzard does not give the opportunity to select Thunderbird files.
View 4 Replies
View Related
Jun 28, 2009
If I decide to upgrade to Win 7 and do a clean install, could I use Easy File Transfer to retain my Outlook, Web Settings and Files? I have two internal hard drives, not raid, and an external eSATA drive. All 3 are the same size, 500GB. So I think I have the resources, I just don't want to lose data, favorites, contacts, files or emails. Having never used Easy File Transfer, how should I proceed? Store my easy transfere to my second HD "D", format C, install Win 7? I guess I need to buy a version of Win 7 that will read my Vista Easy File backup...duh... Is Win 7 Pro able to read Vista Easy File Transfers? I have two accounts on this computer, mine and my wife's, so there another issue too.
View 4 Replies
View Related
Nov 24, 2009
After I started windows 7 easy transfer on Vista Home Premium 32 bit, it runs for a while, then says "please reboot your PC and try again". Rebooted a few times and still get the same error. I got tried chkdsk at reboot time and 'Repair your computer' using vista DVD instal disk.
View 6 Replies
View Related
Jun 6, 2007
I got it for my XP Desktop computer, and on my Vista laptop... Ive tried to send files, and it finds and recognizes the files i want to send... but when go to transfer them, hte flashes the disconnected sign near the exit button. This is after about 30 seconds into it aswell.
View 4 Replies
View Related
Jun 12, 2008
I want to transfer all data from my main computer to a standby computer (without losing the data on the main computer) and then to synchronize them both on a daily/weekly basis, both with OS Win.Vista Business. I am advised by Belkin that their Easy Transfer Cable for Windows Vista is not 100% reliable for this purpose and they do not have a cable or software to do this job.
View 4 Replies
View Related
May 31, 2008
This is probably a very simple question, transferring from xp to vista using easy transfer, over the years theres been a lot of stuff duplicated and deleted on my xp machine. I believe all these deleted copies and all the other deleted stuff stays on the computer, just not visible. Does esay transfer transfer all this deleted stuff as well,and if so is there anything special I should do to my xp machine to stop these copying. Don't want to fill the vista before i've used it with deleted stuff.
View 9 Replies
View Related
May 24, 2009
I am trying to transfer the e-mail from Outlook Express 6 on one computer to a Vista machine and import them into Outlook 2007. I have had no luck.
View 6 Replies
View Related
Jun 23, 2008
I tried out Vista Ultimate 64bit for a month and got whipped by driver issues. I installed Vista Ultimate 32bit on a 2nd partition and tried using Windows Easy Transfer to transfer files and settings from the 64bit installation and pick them up in the 32bit installaion. This is the error I get every time I try to complete the transfer: "The store you selected was saved on a 64bit machine. Windows Easy Transfer cannot apply the data." Is there a way to use WET to transfer files from a Vista-64bit installation? If not WET, is there another utility?
View 8 Replies
View Related
Jun 13, 2008
I've just upgraded to a new pc with vista and windows mail from Xp & outlook express (with virgin). To save my files and emails etc I used windows easy transfer software and copied the files to an external hard drive and then loaded it to the new PC. I initially had problems as my modem didn't install but virgin sent me a wireless connector and all seemed OK. However, when I click on send/receive mail I get an error message 'some errors occured while processing the requsted tasks - please see details below.' But there are no details! I have 3 email addresses.
If I click on the little arrow next to send/rec and then click on each email separately there is no problem. Equally, if I click on 'receive all' there is no problem. When I click on send/rec the first time I open windows mail there is no problem, but thereafter always the error message. I've had Virgin remotely controlling the pc for 90 minutes and they can't suss it!
Also, bizarrely at the top of the page it says inbox - outlook express provided by virgin net even though I appear to be running windows mail (it certainly isn't the usual outlook I have on my old pc). Did I inadvertently load outlook as well as my emails on top of windows mail and they've kind of merged?
View 5 Replies
View Related
Oct 25, 2009
I have a customer with two Vista 64 bits home editions trying to run software that explicitly states its does not work with 64 bit Vista. Oh, what a mess! Question: if I switch her to 32 bit W7 Pro, will Vista's "windows easy transfer" data file work with the transition from 64 bit Vista home to 32 bit W7 Pro?
View 7 Replies
View Related
Apr 4, 2010
When I browse for a printer on the network I can see the workgroup, I can see the PC with the printer, but I don't see the printer show up under the PC in the Add Printer Wizard dialog. This was easy for me back when there were two machines running XP.
I have installed the x86 printer driver on the Vista machine. Would this be easier if I upgraded the Vista machine to Windows 7?
View 7 Replies
View Related
Feb 6, 2009
Computer 1 is my home desktop running Vista Premium SP1. It is on the 'workgroup' workgroup. Computer 2 is my work laptop (on docking station) running XP Pro SP2. It is on a domain called 'amer'. There is an HP LaserJet 2100 connected to the Vista machine. It is shared. This is a wired network with D-Link router. At first I thought it was a sharing issue when I could not print from the XP machine to the printer on the Vista machine. But then I realized it is a network issue because if I try to browse the Vista machine from the XP machine I get the 'no access, you may not have permission', etc. message. To make it work, I :
1. start the XP machine (assuming the Vista machine is already running)
2. wait about 15 minutes for the Vista machine to see that the XP machine is there.
3. Browse to and open the XP machine from the Vista machine
4. Go to the XP machine, open its workgroup (amer) and then open the XP machine
5. Wait a minute or so, then while still on the XP machine, navigate to
Vista machine's workgroup ('workgroup') and open the workgroup. If the Vista machine appears I am good to go. I don't need to browse it, it just needs to appear.........................
View 4 Replies
View Related
Jun 24, 2008
Its been about three months since I've given up trying to network my Vista machine with my XP machine, but I thought I would try it again. here are my symptoms again:
*Vista (Ultimate) machine cannot see XP (Home SP2) machine.
*XP machine can see and access the Vista machine.
*Xp machine shows up in the Vista Network Map, but not the Network Folder.
*Both machines can ping each other.
*I can access the XP machine via IP address, I can access the shared folder but not a shared printer.
*IPConfig for Vista shows that NetBIOS over TCP/IP is disabled even though it is enabled in the Network Adaptor Properties dialog. (NetBIOS over TCP/IP always enabled, the middle radio button)
Other information:
*Everything worked as it should once apon a time, then it all went to Hell. It could have been an update, tweaking software, or antivirus setting, but I notcie too late to do anything about it.
*I know it can't be that I don't have the same User/Password on both machines (I tried it anyway but it still didn't work), because it worked awhile back without having the same accounts on both machines.
*I had Bitdefender 2008 on the Vista machine, the Firewall log had entries that the ports 138 and 139 were being refused, despite having the XP machine being on the trusted list (by its IP address). So I uninstalled the Antivirus, but the problem persists.
*The XP machine has Zone Alarm Internet Security.................
View 5 Replies
View Related
May 30, 2009
It seems today is my day for asking goofy questions
My windows 7 dual boot OS is the one I use to play all my games now, which by the way, I did not know this would be the case, hence, why I only made it about 40 GBs, leaving the Vista partition the bigger of the two.
Well, it has come time to install, yet, another game but I only have about 5 GBs left and the game needs 10GBs to install. Sure, I could uninstall the other 2 games I have already installed but, I am only half way done with them.
Anyways, I have plenty of space on my Vista partition and I would like to know if Acronis Disk Director is as easy to use as I have read. Aside from this, do I need to be worry about loosing any info (images, documents, etc, etc) on my Vista OS once I start the process or should I stop worrying so much.
View 9 Replies
View Related
Apr 28, 2008
Is there an easy way to select more than one item when trying to copy picture files to an email or website for sending over the internet? I remember I used to be able to select the first item and hold down the ctl or shift key select the end item and all the items inbetween would be highlighted for copy? Now, with windows vista, I have to click each one and sometimes it won't even let me do that, I have to do one at a time, depending on what I am doing.
View 6 Replies
View Related
Jul 5, 2008
I have the following issue and hope that somebody can give me a hint about what might be going on! My system has two raid 1 arrays - one is running on XP Professional SP3 the other one is running on Vista x64 Ultimate SP1. When I start my virtual machines (either from the Virtual PC console or when double-clicking the *.vmc files) than everything is working fine on XP and the virtual machines are booting and running as expected. However, on Vista the following is happening (and I hope somebody has an idea):
1. Starting the Virtual machines from the console leads to an immediate reboot of my host machine (I can't even see any boot screen of the virtual machine - it is like clicking start in the VPC console -- > reboot of host).
Now I tried the following:.........
View 9 Replies
View Related
Aug 20, 2008
Does anyone know if there's some reasonably easy way to get hold of all the windows updates for Vista x64 since service pack 1? I'm working on a slipstreamed disc and would like to include them, but it seems like it'll take HOURS of clicking.. And I *really* don't feel up to THAT task.
View 5 Replies
View Related
Sep 25, 2009
I have been trying to find information on hp easy setup frontend but not having to much luck on finding out what is is, do I need it and if not how to remove it if possible or if it harm my HP Pavilion computer if I do remove it.
View 5 Replies
View Related
Sep 29, 2009
If you have a good DVD video and want to share with others, you may need to convert DVD to MPEG4 in order to reduce its weight.For those who seldom do DVD to MPEG4 conversion, it may be troublesome when it comes to relative settings. With Leawo DVD to MPEG4 Converter,such troubles and worries are taken away. What left to you are only a few clicks within everyone's knowledge. You can also deal with the video through extra editing functions like extracting soundtrack, cropping out the black margin, cutting away head and tail, etc.
Then, how to convert DVD to MPEG4? Take Leawo DVD Ripper for example, it provides a typical easy-to-use interface, on which users may face the basic settings only. The first step is to load a DVD resource. It is possible to load DVD resource either from a DVD disc or a folder on your harddisk. When the loading process is complete,a list of DVD video content is shown by titles and chapters. This information is contained in a file by an extension of .inf, so if you don't see the list, it is probably the inf file is missing or corrupted...........
View 4 Replies
View Related
