Im running Windows XP Pro. For some reason my right audio channel no longer works. I have tried swapping sound cards but it's the same result. In my Sound Blaster config I click test channels and I hear the voice say left channel then it goes to right channel and I hear silence. Any idea how to get the right channel working?
View 10 Replies
One of the channels to my old on-board sound card blew out so I bought a new sound card this morning (PPA Int'l 6 channel pci). I have 5.1 surround speakers and when I play movies they all work fine and sound great. But one thing is missing. In the old sound card any sound in windows would play in ALL 6 speakers at the same time. So if I opened WMP it would play the song on all speakers. With this new sound card it will only play on the front right and front left speakers. Also in the audio properties, there used to be sliders for FRONT REAR and CENTER. Now those are gone. Ive loaded the software from the cd and it doesn't help. Also my Speaker Setup found in the advanced audio properties is set to 5.1 surround like normal. Is there some kind of program out there that will make windows use ALL channels for playback like my old sound card?
View 4 Replies View RelatedIs there any difference between the primary and secondary IDE channels? I have my hard drive on secondary and my DVD 16X burner on primary. I tried this because when I put my DVD burner on secondary it would only get Multi-Word DMA mode 2 while the HDD got UDMA mode 5 on the primary. This is a new burner and capable of UDMA 4. After troubleshooting I switched channels and got UDMA mode 4 on the DVD burner when on the primary as master and still got UDMA mode 5 on the only HDD on the secondary as master. I don't understand the difference and the computer works fine and it appears I am getting the transfer modes I am supposed to.
View 6 Replies View Relatedhow do I transition from audio/music overlay to original audio within the movie?
View 3 Replies View RelatedI don't get Audio when I play a DVD. Audio works otherwise.All the sounds one would expect. But nothing from a DVD.
I tried playing with the digital audio settings for each of the DVD drives
I just got a new computer with an AMD Duron processor, 512 M RAM and Windows XP. Only problem is I've got no audio. I've checked BIOS and sound is enabled but Windows doesn't seem to recognize that the speakers are hooked up. When I tried to play system sounds from the Control Panel, I got an error message that said cannot play sound, your sound card may be in use. The computer was a gift that was bought used and the shop didn't have any documentation with the system. I think this might be a driver issue but I'm not sure how to find out which driver to try.
View 8 Replies View RelatedI reinstalled my OS and all my software, shortly thereafter I noticed I had an issue where any sound that was coming through my headphones was being retransmitted through the mic, with further testing I found that this was not actually the case but rather any sound that would be output is being retransmitted as audio in, even if I had no speakers, headphones or mics connected. I have looked at and experimented with everything I could in every sound settings.
I have tried updated drivers, the only way for me to stop the issue from occurring is to mute the mic in the recording control, but that stops me from using the mic altogether. I need to be able to use my mic without recording anything that I am hearing as well.
First off I use windows XP with the latest service pack. I'm using the onboard sound card on my motherboard Asus striker II extreme.
The volume of my flash player (I first noticed it when trying to view a video on Hulu) but other flash embedded videos won't play sound either. I thought this was a flash problem, and tried the usual fixes uninstalling reinstalling, running the update utility and removing and reinstalling the plugin. Also it likely isn't a browser issue as embedded videos didn't play on either Firefox or Opera.
After restarting my computer after a few uninstalls I noticed my startup music wasn't playing as well. I'm thinking that it might be some registry error as it seems like the music is very quiet instead of muted, and all of the volume levels in the Sounds and Audio Device Properties menu are at the correct levels, and my other media players play music and movies just fine.
I've browsed the forums and haven't seen anyone with a similar problem or a fix, so any help would be greatly apprciated.
After hardware upgrades, my custom XP Professional audio workstation will not allow me to re-install my Digigram VX-442 audio card driver or on-board audio.
Error message is: Cannot install this hardware.The data is invalid.
i have lost audio driver
View 1 Replies View RelatedI have tried to play DVDs on my HP Pavillion notebook. I am running Windows XP Media Center Edition. I have tried using the Media Center (Play my DVD), Windows Media Player, Real Player, etc. In all cases, I get the video, but no audio. When I put in an audio CD, it plays fine.
View 3 Replies View RelatedI do not know how to determine the CPU load of audio on a motherboard how to determine if the sound includes a digital signal processor (DSP). I assume a DSP, especially for older CPUs (600 MHz. or so) is a big improvement because it offloads a lot of processing from the CPU. I am interested only in stereo. How can I know if an add-in sound card with a DSP is actually an improvement? Does the DSP overweigh other issues, eg. does a cheap Mad Dog Prowler 4.1 DSP sound card offer an improvement over the motherboard sound of a Compaq DeskPro ENS/P600? Truth is, I've been looking for but have not seen a treatise on this topic. Does anyone have any links for me to pursue?
View 5 Replies View Relatedmy audio/volume system tray icon has vanished and device manager says that all sound devices/drivers are working properly and are up to date, BUT - Sounds and Audio Devices Properties says I have no audio device installed. If I try to open volume controls
View 4 Replies View RelatedFormatted hard drive no sound Sound & audio tells me I have no audio device I'm running an E machine.
View 6 Replies View RelatedA new machine with a new XP build who is unable to hear audio from his machine. After taking a look at his machine I noticed he had no audio driver installed. Thinking that this was a simple fix I attempted to re-install the Realtek HD Audio drivers that are included with the machine (HP dc-5750). After installation and restart I receive the new hardware detected prompt and I navigate to the directory with the .sys file in it. When attempting to install it the wizard states that it was unable to locate the drivers. I know the drivers are correct and I have even attempted to download updated drivers.
This is when I started to search the forums, all stating to remove the drivers and remove the UAA hotfix from Microsoft and re-install both. (UAA first then drivers) This failed to produce any results, so I looked around more and found an article stating I needed to extract the files into a folder and direct the new hardware wizard to the commonfile folder in the folder. This left me still without sound or a working driver.
Im new to this forum but i am so thankfull that this site is hereMy problem is my 11 year old son downloaded a program that was supposed to find duplicate copies of files on his PC and delete them.Well he did this but in doing so he deleted some boot files(i beleave) and he cannot boot up.He downloaded the 4 bootdisk files from the net but still will not boot up from floopy drive either.The error message reads this>>> 'Windows 2000 could not start up because the following file is missing or corrupt....<windows 2000 root>system32 toskrnl.exe. Please re-install a copy of the file.His computer is a IBM with windows 2000 loaded.I beleave there are 2 copies of windows 2000 on his computer because when he tries to bootup it gives him a choice of either copies.Ive tried the windows 2000 CD to boot in the cd-rom drive but either its not reading or maybe its because the disk is a copy and not original.
View 2 Replies View RelatedCurrently my AIM program keeps on restarting and says "trying to reconnect..." and when it finally reconnects, it does the same thing again for about another 5 times. I've already downloaded a new version of AIM, ran AIM bot, and the program still progresses.
View 2 Replies View RelatedBrand new intel p4 has issues. Please help. it shows the intel p4 screen, start bios then gets a few 95,BA, 94, E9. Then gets a long consistent beeping noise. It sounds like the bios is messed up.Under system summary,says sys manufacturer intel system model D945gtp system type x86-based pc
View 9 Replies View RelatedI upgraded from Windows 98 to Windows XP, and every since I upgraded my computer had been a mess. I don't think my Virus Scan is working right and I have eTrust EZ Armor 2005 which is one that Microsoft recommends. My floppy drive isn't working either. I get a error message that says my driver is corrupt Error 39. My memory got full. I have 10 GB memory and I only have 4.17 left now. I have 512 Ram in my computer, but I don't know how much is left and don't know how to find out. Since I upgraded I can no longer shut my computer down from my desk top. I go to Start and click turn off my computer, then I go to shut down. I seems to go through the motions, but a screen comes up and says it is safe to shut my computer down, well it won't shut down with the button on thefront, so I have to push the button on the back of my computer.
View 3 Replies View RelatedI messed up my registry and now I can't get any audio, and my DVD and CD ROM drives won't play music/movies. Luckly I have a copy of the registry saved on my hard drive. When I try to merge the file I get this error " Not all data was successfully written to the registry. Some keys are open by the system or other processes" How do I go around this? I really do not want to re-install windows again.
View 6 Replies View RelatedWhile I was using the program, DVD Shrink, the screen from the program froze up. So I turned my power on and off to restart my computer. When I restarted it, Windows XP had a blue screen on which I never saw before that said it would go through 3 stages to fix any errors that shutting down my computer may have caused. After Windows automatically restarted, what comes on my screen with all the desktop icons is now messed up-- as programs automatically try to open, I get a box like this:
"ituneshe/per.exe- Bad Image The application or dll c:/windows/system32/att.dll is not a valid windows image"The same would happen for my anti virus program, and AIM.I can still access all my documents, and my internet works fine. But the startup process seems like the beginning of problems to come in the future. Does anyone have any advice how I can remedy this?
When ever i click on minimise the screen i wish to do so shrinks in the normal way but appears to disappear behind the task bar. So in my task bar i have nothing. But when i activate task manager its still running.
View 1 Replies View RelatedMy computer keeps rebooting on me for NO REASON all the time. At first I thought it was my Hard Drive because my computer had become forgetful and when i tested it I found that I had "137 Reallocated Sectors". So I went out yesterday and bought me a new one. I have reformatted and it's STILL rebooting. I am about to pull my hair out..it's getting so frustrating. Here are my specs.
View 4 Replies View RelatedMy sister sent me a link to a website with a 'funny video' and I downloaded it. Stupid, stupid, stupid. Anyway, I right-clicked and opened with VLC, and I have no idea how many different VLCs opened. The screen went black and suddenly my desktop is set to 4 bit color and 640x480 resolution. I can change the resolution, but every time I try and change the color, the screen goes black for a good 30 seconds, and when it comes back, it says "your settings have been changed do you wish to keep the bla bla bla" - but it's still at 4 colors. And while it's at it, it switches the resolution back to 640x480. I'm not sure what you need to know for this... I have WinXP and my video card is an Intel 82810E.
View 1 Replies View Relatedcuz of this stupid AIM virus, that was a .pif file... it started sending the message to other people, so i shut down my pc. Then i tried to reboot but my password wasnt working, so i went into bios, and not knowing what i did i went to change startup pass and changed it... now when i reboot it says use a startup pass, but it wont even let me type it in....and i dont know how to start windows xp cd at reboot cuz for some reason it doesnt go through even when i enter the BIOS....can someone please help me? my pc is messed up.
View 11 Replies View RelatedI have a big problem, I was trying to change the icons for my file types in explorer specificaly under tools/folder options/file types. Well I changed the icons for the AudioCD,DVD,Drive,File Folder and Folder there was no bad results from the audio and dvd nor the others, it just didnt change my icons to what i wanted it to be so whatever i moved on. Well after i did those things i started to notice that when im using explorer every time i open a folder it would open in a different window so im like maybe i forgot to put a check in the open in the same window in the folder options. So I checked and to my suprise it was checked. I started to search the web for answers and I found a forum and saw that the problem could be in my registry specificaly in HKEY_CLASSES_ROOT so I deleted the Folder,Directory and Drive registry folders in HKEY_CLASSES_ROOT now I cant access my C drive and my folders fortunatly i can use my browser and other apps i just cant access my drive and documents .
View 3 Replies View RelatedHey guys, not sure if this is the correct forum for this but here we go.I have 7GB's of HD space that is being unused. It is not labeled or anything it is just there. I got Partition Magic to try and merge it with my C drive (due to that is where it was supposed to be in the first place). Anyway, it is not working, is there a way to do this that I am missing (without having to reformat the drive). During initial install of XP, created to partitions of one 80GB HD (C and D).C has 13GB (Should have 20) and D obviously has the other 60.If it comes down to it, I am prepared to backup HD onto an external then re-install but would really like to try and avoid that.
View 2 Replies View RelatedI was trying earlier today to reinstall my Windows XP, but I have the upgrade version so I had to install ME first. All my hard drives were in the NTFS format, but when I just checked, everything is in FAT, and every hard drive, including my backup hard drive is only partitioned to 1.99 GB. I lost all the data on the backup drive, but I was wondering if I would be able to recover it by restoring the partition or something? How would you guys reccommend I recover the data on my backup drive?
View 10 Replies View RelatedIt keeps restarting itself. its pretty random, sometimes it wont do it all day or it will do it so often that i cant even log onto windows without it happening. it has been doing this for about a month. i have a virus scaner program and it is not detecting any viruses
View 2 Replies View RelatedWell, I really did it this time... I decided to upgrade my laptop to XP... backed everything important, did the upgrade...everything seemed good. Worked. Then it notified me that the Norton was not working, & advised me to uninstall & reinstall... so I did... only thing is, I went ahead with the restart! I should of looked for junk/trace files, especially since it said it didn't completely remove it. So, when I restarted it, XP keeps coming to a screen that checkes the file system, fat ,32 scans & fixes files... dump files, etc. I can get to the IBM Bios setup, but I don't really know what to do from there.When I use a boot (maybe the one I'm using is no good) it says C: doesn't exist... I did try to start in safe mode, one of the times it appeared... but it didn't change the screen still did that fix-it thing.
View 9 Replies View RelatedI installed the stuff on the CD and it tottaly messed up my pcWhen i restarted it kept on restarting and restarting it only came up to "Welcome to Windows'So I had to do a System Restore.
View 3 Replies View Related
