Graphic Cards :: Main Display Doesn't Work When HDMI Is Plugged
Oct 25, 2013
Last night I got hold of a 27" BenQ GL2750HM, so far so good. I have my main display from the DVI port to HDMI port on the screen and my secondary screen is my 60" TV which is connected through HDMI port on the graphic card into the HDMI port in my reciever.
The main scheme for my setup is like:
- Radeon 7970 DVI > HDMI Main monitor (BenQ GL2750)
- Radeon 7970 HDMI > HDMI Reciever (ONKYO TX-NR609)
- ONKYO TX-NR609 > 60" TV
So to the problem now. When the HDMI cable is connected to the graphic card, I need to have my TV ON in order for my main monitor, the BenQ, to work and if I turn off the TV the BenQ is getting black, like a standby mode, however, there is "no signal" to the monitor.
This was never a problem with my other screen, I could have the HDMI cable connected to the graphic card, the TV off and the reciever OFF without the main monitor went black.
View 5 Replies
ADVERTISEMENT
Aug 19, 2013
I have a HP Pavilion dv6t-3000 CTO Entertainment Notebook PC.
I upgraded from windows 7 to windows 8 64 bit. I have an ATI mobility radeon HD 5000 series (Microsoft Corporation - WDDM v1.20) and an intel(R) HD graphics card.
Next to the ATI mobility in device managers, there is an exclamation point in a yellow triangle. when i open it up, it says
This device cannot start. (Code 10) {Operation Failed} The requested operation was unsuccessful.
I have tried updating it but it says it is up to date. i have tried going to the HP support page but it only gives me options for a windows 7 computer and says there is nothing for my computer for windows 8.
View 6 Replies
View Related
Aug 22, 2014
I have nvidia GTX 760 2gb ram with a Magnavox 39" Class 1080p 60Hz LED TV - Black (39ME313V).
The HDMI refuses to show up while RGB works Ive updated drivers the mirroring for windows 8 does not work.
View 3 Replies
View Related
Aug 8, 2014
i finally worked out how to get full screen on my tv when connected via hdmi from laptop, which is great. only now found that when i shut the laptop screen i lose the full screen on the tele and it sizes down to about 50% with the black boarder. on my laptop control panel "what does computer do when i shut the lid" i have selected "do nothing" on both wired and battery modes. How I can close the lid and keep full screen? (the tv is a celcus full hd smart something or other and laptop is hp running windows 8.1,
View 5 Replies
View Related
Jun 19, 2013
When I hook my laptop up to the TV with a HDMI cable my laptop screen goes dark and the TV only shows the task bar and the desktop background. Sound works. No mouse or actual programs are displayed. I would like to mirror the TV to my desktop. My laptop is a HP Pavillion Dv7-4285dx running Windows 8 Pro 64 bit.
View 9 Replies
View Related
Mar 25, 2014
I have a AMD 5650 that shows a black bar that is 1 inch on the left and right and about .5 inches on the bottom on HDMI. I've used the drivers that Microsoft provided and also beta drivers from AMD from Febuary 2014, nothing seems to work. I've taken a picture, I've underlined where the back bars are in red.
View 3 Replies
View Related
Sep 5, 2013
Well I have been having issues with my monitor. I had a Toshiba laptop I had hooked up to my monitor, everything worked great. It then crashed, I got a new Dell with Windows 8 64bit and Intel graphics. I have an HDMI to VGA adapter cause my laptop doesn't have a VGA port and monitor doesn't have HDMI. So I hook it up and get it to work but "Input Not Supported" was floating around the screen.
So I changed the resolution. The only resolution that makes the "Input Not Supported" to go away is 1600X200. Well its clear picture but I have the annoying black bars on the side of my screen. I have looked around and everyone says to go to the CCC but I can't find it on here and from what I understand that is for AMD only(if I'm mistaken how to make it work cause I have attempted it). So is there an Intel version or how do I fix it?
View 7 Replies
View Related
May 27, 2014
My wife has a nice new VAIO laptop. We connect it to a Samsung TV with an HDMI cable. Initially there were video artifacts on the TV screen, but after some fiddling they seemed to go away. Today they have returned. I have tried another HDMI cable and it didn't work.
The artifacts are only on the TV screen and not on the laptop display. They cannot be captured with a screenshot (I just tried this and am posting from my computer).
The web search picture (HDMI.jpg) shows small vertical lines in a row after some of the text.
Sort of like this: | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
But less than the height of these lines. There is also a set of the lines that follows the mouse cursor around.
The VAIO desktop picture (HDMI2.jpg) shows "sparkles" around the VAIO name and spreading to the left where it takes up the entire side of the screen.
View 1 Replies
View Related
Oct 3, 2013
Whenever I restart my computer I sometimes get in red letters a warning saying you have not plugged in your graphics card and a loud beeping sound. I already checked it and made sure it is fully plugged in, what's going on?
Also, only when restarting it occasionally gives me that warning. Other than that, its fine booting up, never gave me the error. Also if i get the error and press the reset button on the computer it'll do that until I force it to shutdown by holding the power button. And, my display works fine.
View 4 Replies
View Related
Oct 9, 2013
I have an ASUS s550C running windows 8 and my HDMI to my 32" RCA flatscreen doesn't work anymore. The cable works fine with the xbox, correct tv modes, but now as soon as I plug in the HDMI to the Ultrabook the Ultrabooks screen goes black and the tv screen says unsupported. I have tried extended, 2nd screen only, and all screen settings, 720/1080I etc.
View 4 Replies
View Related
Jul 15, 2014
Is there any way I can output the content of my samsung galaxy note 2 to my dell inspiron 7520 laptop via hdmi or vga socket? From my research I found that only the alienware laptops have hdmi input.
View 2 Replies
View Related
Sep 14, 2013
I just purchased a new windows 8 PC. I was attempting to hook the computer up to my tv through hdmi (the pc has no VGA input) and when I went through the normal paces to put the display on my tv (display desktop only on 2), the signal did not transfer and there is no display on either my tv or pc! how to revert the display back to my pc monitor without being able to see anything? Acer support was less than useful. It's an acer aspire z3-605 all-in-one pc.
View 5 Replies
View Related
Aug 25, 2014
I have a Lenovo Flex 14 - win 8.1 (64 bit).I have restored my pc and after the recovery the option to adjust the display brightness has "disappeared". The option is no longer in place in the charms bar or in Power Option and the adjustment keys (F11 and F12) are not working either.
View 2 Replies
View Related
Oct 24, 2013
Just upgraded to 8.1. Now, it won't let me extend my desktop to a second display like I had with 8.0 ....
View 9 Replies
View Related
Nov 18, 2013
I just upgraded to 8.1 and now a game that I play called theHunter wont launch. When I run the launcher it comes up with an error saying 'No Appropriate Display Modes'. It was working fine on Windows 8. The support at the Hunter hasn't been very useful and despite trying a number of different things I can't seem to solve this issue.
View 2 Replies
View Related
Jul 6, 2014
I'm having a terrible time after reformatting my 8.1 machine (desktop).Every time I try to adjust a display setting, such as gamma, some other process overrides it in real-time. Meaning I can't calibrate my display in windows color calibration, or even in my nvidia control panel, it instantly resets it while you're adjusting the slider. I don't know what this could possibly be, but I've uninstalled the Dell display manager, so I assume it's not the monitor overriding it. I also have nvidia control panel set to 'use other applications' for display configuration.
View 1 Replies
View Related
Dec 18, 2013
I use Windows 8 on a rMBP, but frequently use an external monitor that's 1080p. Since it scales 200% for the HiDPI of the rMBP, it's way too big on the external. Is there a way I can have it scale only the internal monitor, and leave the external one at 100%?
View 3 Replies
View Related
Oct 10, 2013
I know how to select the second screen options, however, my Surface Pro and our Samsung Laptop both running Windows 8 cannot detect a second monitor/screen. We are connecting via the HDMI port, but it will not display no matter what option we choose nor whether we run it from the desktop or apps. This is what we use for work to display presentations for clients.
View 3 Replies
View Related
Jun 11, 2013
How can I enlarge the display, at present it is only using a strip down the middle. Pointless having a nice big screen.
View 3 Replies
View Related
Apr 3, 2013
Original error message: "Display driver NVIDIA Kernel Mode Driver, Version 314.22 stopped responding and has succesfully recovered"
I'm getting this error again and again, mainly in games. (Which seems logic, they use the graphics card most) Games without DX11 will continue after a black screen has occured, but at very low FPS.
Games with DX11 will just crash and stop working after the same black screen.
View 4 Replies
View Related
Aug 23, 2013
Both primary and secondary displays are 1080p, native. Windows says both are running at 1920x1080, but I can visually see the secondary display is running a lower resolution. The GPU is GeForce GTX 560M, with the latest drivers. I didn't have this issue with Windows 7.
View 1 Replies
View Related
Jul 3, 2013
My problem is that I can't change resolution on my laptop's display with win 8. It's quite an old, Toshiba Satellite M70. I installed win 8 directly from XP. Everything is working fine except this. I tried to install the old drivers in compatibility mode, but says the system requirement is not enough. Do I have any chance to make it work?
View 5 Replies
View Related
Apr 9, 2014
I'm using Windows 8.1pro,also I use HDMI to sometime output video files on a TV screen,that works fine. HDMI cable is always plugged in,primary display is set to my computer monitor.I don't always use TV screen and because of existing cable connection my OS extends image to second screen and my mouse cursor alway disappear when it goes to borders,that is an annoying situation,is there a way to disable/eanble extend display on second screen without unplug the cable,just like I can set default output sound device (computer/hdmi sound) ?
View 3 Replies
View Related
May 22, 2014
i bought new computer few days ago.i have sapphire HD 7750 2gb ddr3 - and im installed the driver for that by the CD but after i want to play some games . i get this massage Display driver stopped responding and has recovered.
View 8 Replies
View Related
Jul 13, 2014
I have a laptop where my LCD is broken on the left side, but the right side works fine. Is there a way I can change my display to only show on the right side? I've managed to make the display horizontally smaller, but I can't figure out how to change the center to the right side. This is annoying because I have to re-size every window every time I open it, and then I have to constantly scroll back and forth on web pages. I'd rather be able to maximize and have it only on the right side. See the attached picture to see what I'm talking about.
View 2 Replies
View Related
Jan 9, 2014
I am on a laptop with a gtx 765m. I am trying to connect a thunderbolt port to a display port monitor. My understanding is that thunderbolt is backwards compatible with display port. But, for the life of me I can not get it to work.
I am using a minidisplay port -> display port cord.
I have ended up hooking the monitor up with an hdmi cord for now. FYI the monitor is a 2560x1440 monitor if that matters.
View 4 Replies
View Related
Jan 30, 2014
I amm using windows 8.1 64 bit and everytime I open Photoshop cs6 for the time after a boot I get this message 'Display driver has stopped working but has recovered', my system can handle photoshop so I know thats not the problem. My graphics card is a AMD Radeon HD 8330.
View 9 Replies
View Related
Jun 2, 2013
For last couple days I've been going through a minor computer issue. I wasn't doing anything special, I just turned the computer off. And the next day the problem occured; After bios and Windows 8 loading screen ( the little dots going round, just below the windows 8 icon ) my screen goes black and there's no signal to the display. I've already tried formatting my hdd and installing windows 8, also tried doing Reset option, from the Windows 8 troubleshot system. I can't access my Safe Mode, because it tells that Windows can't finish the installation in safe mode ( After installing the new system I format all the data and it goes just fine until the windows icon and "Preparin your devices" sign. It goes 100% and gets black again.
View 7 Replies
View Related
Jan 22, 2013
In a few weeks (I can't wait! ) I will replace my laptop with the Surface Pro.
Right now, though, I have my laptop connected to two monitors: One via VGA and other via DVI. I'm running Windows 8 Pro x64, so this all works great.
So the big question is whether it is possible to have multi-monitor support via the one-and-only DisplayPort that is on the Surface Pro? If so, what--if any--additional hardware would I need?
When I'm docked at home and using my Surface Pro as laptop, I really need to keep the functionality of using both external monitors (one is 31" and the other 29"). I would really hate to go back to only being able to use one.
View 9 Replies
View Related
Jul 25, 2014
So I'm running 2xR9 290X (crossfire) with 3xQnix Qx2710 monitors. One of the qnix monitors was purchased with HDMI/DisplayPort connectors along with the usual DVI connector (normally these monitors only come with the D-DVI input)
I had a 2 monitor (with just the two DVI-only monitors) setup for a while that was working fine.
Since installing the third monitor I'm experiencing several weird things:
- On boot, until the Windows login screen comes up (Windows 8.1), there is nothing on the non-primary DVI monitor (so my setup is my primary monitor is one of the two DVI monitors, and then the left and right monitors is another DVI-only and the DP monitor).
- If the monitors go to sleep, or I put the computer to sleep and wake it up, any windows that were on the non-primary DVI monitor are moved over to the primary DVI monitor. Windows on the DP monitor do not move in this configuration.
- Within CCC, after sleep / monitors off, I have to restart CCC's control of the color settings for the non-primary DVI monitor. (I'm forgetting what the actual button says, but it's the button under the Display color controls settings where you can manipulate the R/G/B channels - I have to use the GPU for color matching since the monitors don't have any inherent ways to change R/G/B levels
If I only connect the two DVI monitors this is not an issue.
If I connect one DVI and the DP monitor, after sleep/wake any windows that were on the DP monitor are moved over to the primary monitor (again, note that this didn't happen when all 3 monitors were connected).
I have tried the newest version of CCC, as well as the current beta version - same behavior in both.
I have tried using HDMI instead of DP - same behavior
Aspects of this sound similar to the issues discussed in this post : [URL] ......
What I don't understand is why the second DVI monitor is acting so oddly when all 3 monitors are connected. Why would there be no picture when the computer boots?
View 1 Replies
View Related
Mar 20, 2014
I'm not sure if this problem is with the GPU, but I think it might be a good place to start.
Up until recently, I was running Windows 8.1 on a custom build with the following: Athlon II X4 610E processor, Silverstone NT01-E cooler, MSI 890-GX MoBo, 4GB OCZ DDR3/1333 RAM, Zotac GeForce GT 240 GPU, AuzenTech X-Fi Home Theater Sound Card, Western Digital 2TB Caviar Green, Corsair GT 120 SSD, Samsung SH-B083 ODD, and Silverstone NightJar ST40F PSU.
With this build I noticed that there was a certain tendency for the screen to "flicker" when the video changed (ie, starting a Netflix video, a Hulu video, movie on WMC, etc). It generally occurs at the start of a video and it's conclusion, being most annoying on Hulu because it does this at the start of a segment, just before the commercial break, and during the commercials.
Since I'm transitioning to gaming on my PC, I replaced several components, upgrading to a EVGA GeForce GTX 770 DUAL SuperClocked GPU, Intel Core i5-4570 processor (stock cooler), CORSAIR Vengeance LP 16GB (2 x 8GB) RAM, ASUS Q87M-E LGA 1150 MoBo, and CORSAIR CX series CX600 600W PSU. I also reinstalled Windows 8.1.
I had hoped that this would clear up my issue as a side benefit, but that is not the case. In fact, in some instances it's frequency has increased, mostly only occurring at the times I've come to expect, but I was watching a Hulu video just a few minutes ago and the number of times the screen flickered was nearly unbearable.
View 7 Replies
View Related
