I bought a Transcend USB flash drive in India - 32 GB - unopened packaging - which Transcend later claimed is counterfeit. Using several computers, I cannot access the drive.I cannot format the drive using both W7 and DOS formats on different computers. The format always runs almost to the end and then fails, reporting corrupted directory.I am not trying to recover any data - I only wish to repair (uncorrupt) the directory?
View 7 RepliesI am a moron and I messed up the disk partitions on my laptop. I was tryin to increase my Cdisk space by allocating the free disk space from my D. I used this software called "partition magic" and just when everything was going smooth..some error occured and the partition did not take place..to make things worse..I can't acces my D, The error message says "D: is not accessible.The file or directory is corrupted and unreadable."No clue what to do..I NEED to recover my data from my D drive..What should I do?
View 3 Replies View RelatedI got pop up in utorrent says a directory is corrupt, I start to run chkdsk on that drive. In this case in have drive letter E. I click on computer, then go to the drive, right click, properties, tools, check now. It says the drive is need to to forced to dismount. I click on ok. then in computers, the drive just show the letter, not size or disk meter. In the open windows on task bar, I did not see scan disk running, or maybe I accidentally closed because I was switching between several programs.
I thought restart pc the drive will show again, but after restart, the drive does not show up, it says 'E: is not accessible, the file or directory is corrupted and unreadable.' I tried to start pc 2 times, still same. I downloaded Partition Wizard Home Edition (minitool partition wizard home edition 5.2) and running it, it showing my files are still in the drive, but not accessible in windows. I also run chkdsk in recovery environment, but still says disk is corrupt, chkdsk cannot continue.
I just purchased a new USB 256 GB flash drive to transfer documents from my desktop to the flash drive after the process completed I rebooted the computer when I opened my computer the flash drive was showing invalid characters when I opened a flash drive document they also had invalid characters labeled to them and I get the following error " The filename, directory name, or volume label syntax is incorrect."
View 14 Replies View RelatedI've been using a flash drive for coursework and transferring data and windows 7 suddenly decided it was corrupted despite me finding no problems with it. So me being me decided to allow it to try and fix it and guess what happens, I wind up with a file with the same name as the folder it decided to remove and a new folder full of what looks like setting and configuration files (got a cog icon, cant remember what extension they have). How do I recover files that haven't been backed up???????
View 1 Replies View RelatedI have Dell 15r, which runs on win 7 home basic, i recently started using toshiba hard disk,i have some files in the external hard disk when i try to move them or delete them i will get this kind of error message. Error : 0x80070570 The file or Directory is corrupted and unreadable.
View 1 Replies View Relatedrecently i've been having a problem when trying to move ISO files from one harddrive to another. I've tried with 3 different ISO files and all come up with the same error:"An unexpected error is keeping you from copying the file. If you continue to receive this error, you can use the error code to search for help with this problem.Error 0x80070570: The file or directory is corrupted and unreadable."First time I got this error i just thought something had gone wrong with the download so i deleted the file and downloaded it again. Same problem. This made me think that maybe it was just that download but now I have tried 2 other files and gotten the same error every time. This only happens with ISO files though as in case it was the harddrive or connection issue I tried transferring some other .avi files and they went across without problem.
View 9 Replies View RelatedUp until last friday, my computer worked perfectly fine.Then after i came back from school, i turned on the computer and it went straight to startup repair. I kept receiving messages that said "The file or directory D:Windows is corrupted and unreadable. Please run the chkdsk utility" I let the startup repair work overnight but as i checked today morning, it was STILL going on. I then decided to use the chkdsk /f /r but it did not seem to help. I also tried to install windows again but it kept saying it was corrupted.Currently, i believe that my hard drive is failing(which is sad because i just replaced a failing hard drive about half a year ago that came with this new comp)
View 1 Replies View RelatedI have WD external HD, but to my surprise this evening I could not open it, it only display this message "The file or directory is corrupted and unreadable".
View 2 Replies View RelatedOne directory (Directory A) containing the same files as Directory B but with the wrong Date created / modified attributes.how to make all the files in Directory A have the same date created/modified attributes as Directory B.
View 7 Replies View RelatedI have a 10 files that have all been categorised into about 40 folders. These files have been damaged.I have a backup of all these files, but they are not categorised and sit in a single directory.Does anyone know of an easy technique to batch replace the damaged files with the originals?
View 2 Replies View RelatedI wanted to have copies of some of the intrinsic Windows 7 operating system command line .exe files located on another drive and directory. When I run C:WindowsSystem32Ping.exe /? at an Adminstrator's command prompt, it runs fine. If I copy this .exe to X:Tempping.exe (X: is on the same hard drive on the same computer), it will not run at an Adminstrator's command prompt. The file on X: has full permissions. I am running Norton Internet Security.
View 3 Replies View RelatedI have recently purchased a USB Harddrive.
I wish to share a directory on it, but when I tried through the share menu, or by clicking on 'share this' in Windows Explorer, Windows 7 told me that 'This folder can't be shared'. When I tried the advanced sharing settings, I get an error telling me that 'there are no more endpoints available from an endpoint mapper'.
Other directories, on my internal HDD, are already shared fine, and a quick test confirmed that further shares from the C drive also work. I am on Win 7 Home Premium and connect to a router via ethernet cable.
I had windows explorer open (Win 7 Ultimate) & suddenly my photos directory disappeared. I used the 'back' buttonm but got the msg that the directory was no linger avalable.
View 3 Replies View Relatedmy pendrive is been shown but it cant read the files in it ..it says the data is unreadable and corrupted..it was working fine ..but i dont know what hapeenf..whn i chkd in command prompt it said that it does not hav system files!
View 3 Replies View RelatedI have an external 1 TB hard drive. Its usually connected to an XP machine, but I can move it to a Win 7 machine. I am unable to delete a directory. I got a hint to try using the CMD window. The top of the dir list is:Quote: K:>dir /XVolume in drive K is 1TB HD[CODE]
View 1 Replies View Related'installation directory must be on a local hard drive' Its not the msi as ive tested it on another computer.The msi is a plugin tool called t-splines by autodesk. Ive also tried older versions with the same error Things i've tried so far
sys restore
safe mode
right click - take ownership
I uninstalled 7zip which i already had, then reinstalled with the .msi from the website to test if it was all msi, however it actually worked I was looking around for other .msi install software just to test it but can't find any?
i want root directory of c drive program
View 1 Replies View RelatedI damaged my drive, while I use decrypting my BitLocker encrypted External Hard Disk, due to numerous disconnection because of loose USB port. The Decryption was almost half way done. Now the drive is not shown in My Computer but it is detectable through other O/S like MAC, Linux as Unknown partition.
View 4 Replies View RelatedHow can you copy one flash drive to another flash drive,on the same computer?
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: AMD Athlon(tm) II X4 630 Processor, AMD64 Family 16 Model 5 Stepping 2
Processor Count: 4
RAM: 3839 Mb
Graphics Card: ATI Radeon HD 4200, 256 Mb
Hard Drives: C: Total - 702932 MB, Free - 657555 MB; D: Total - 12368 MB, Free - 1523 MB;
Motherboard: FOXCONN, 2AB1
Antivirus: Norton 360, Updated and Enabled
I recently installed Windows 7 x64. When I plugged in my external USB drive, it brought up the scan disk box and said I should check for errors. Ran it, and later I found some of my folders/files were corrupted. Tried a couple unerase utilities to get my critical info back, and failed. So, I ran scandisk again. Now almost all the files read as corrupted and it asks me to format the hard drive.
View 3 Replies View RelatedAt the moment, my Gateway M-Series laptop which has Windows 7 32bit will not do a system restore! It says my local disc ( C: ) has errors, it cannot check these errors so that I can restore the computer
My computer doesn't want to connect to the Internet also (lucky for me I have other means of accessing the Internet) and every time I open Chrome or any of my software it says there are corrupted files and the disk check will not run because there are corrupted program files? I haven't downloaded anything of late I keep a fairly clean hard drive, but when I went into system restore it set one of the restore points as 'DirectX Installed' which incidentally I haven't installed and isn't in any programs list.
After some tweaking I found I was able to check the disk and restore the computer but I would still like to know if any of you have any input on how to avoid future problems!!
I copied several large files (between 1 and 4 GB) from one USB hard drive to another. At the target destination several of the files had defects. They were in general not completely unreadable. Most could still could be opened but had clearly corrupted data. how can this be detected/prevented. Doesn�t Windows 7 have some kind of an integrity check when copying files? Also is there any good software to compare files for being exactly identical down to the last bit? Ideally with the capability to compare whole folder contents so that it hasn't to be done file by file.
View 8 Replies View RelatedHow to recover files if the hard drive is corrupted
View 1 Replies View RelatedI'm using Corsair SSD as Windows 7 x64 boot drive, and I moved both User & System Variables TMP/TEMP directory to a new common TMP directory in another hdd (Drive D) & also disabled pagefile on my boot drive (but enabled it for Drive D).
Question is, what happens if I take off my hdd (Drive D and Windows 7 / applications need a temporary directory which doesn't exist anymore ? Will Windows 7 be smart enough to create a new temp dir in the original location ? I wonder if the dependancy on the hdd as TMP directory becomes critical.
About pagefile, I understand Windows 7 needs a min pagefile of 400MB on boot drive to allow memory dump. What happens if I disable pagefile on boot drive & enable it on another drive ? Will memory dump work ?
We had an external USB drive with tons of media files on it connected to computer A running Windows 7 Pro SP1. The drive was safely removed and connected to another computer that was running Windows XP Pro 2002 SP3. I was told that the drive was not recognized in XP and that it was disconnected (I cannot say for sure "Safely") and returned to the Windows 7 computer. Once the drive came up I get the following:
K: is not accessible. The disk structure is corrupted and unreadable.
I know every drive fails eventually and I'm not sure how old this drive is. Any utilities to use to try and repair the file structure. I have only tried rebooting the Windows 7 computer and that did not change anything.
Before I even go further: yes, the "hide empty drives" has been unchecked)I had to reinstall my machine and I was able to to see the drive letters for the internal flash card reader. However I think something might have gone wrong when I give my external HDD a drive letter that was held by one of the flash card reader).I wrote "I think" because I am not really sure since I never wanted to use the internal card reader till today so I never noticed there was an issue. Anyway, the internal card reader does not show up even when I insert a card in the reader. Basically nothing happens. I have uninstalled the "USB Mass storage device" and it gets installed without any issue but the problem is still there: I can't see the reader. the INTERNAL flash card reader has a USB slot and when I insert a EXTERNAL flash drive, the EXTERNAL flash drive shows up.
View 4 Replies View RelatedI know, should have a backup, I was actually about to create a backup when the flash drive failed on me unfortunately. My newest backup is from about 5 days ago, so I'd prefer to be able to restore the current files.
I moved the drive over to another computer and tried to save a file but when I checked again the file was gone, like it never saved at all. Subsequently, after removing and plugging it back in the computer did not detect the drive (or see it in disc management). It does show up as a generic USB drive in the device manager, but there are no properties for it.
When I add it to a computer, it still adds drivers for it, but then nothing happens after that. It may also be a hardware problem, since the drive fell on the ground pretty hard a while back, but seemed to be working fine. There isn't an easy way to open it up and check.
I also tried using a few data recovery programs, but they couldn't detect the drive either.
I have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
View 3 Replies View RelatedI recently ran into a very weird windows 7 bit problem after installing it on my desktop. I cannot copy large files/ holders into usb flash drive or write large files to cd/ dvd. The copying/ moving process would stay on for about 5-10 seconds then freezes then I get an error message. That is:
H: refers to a location that is unavailable. it could be on a hard drive on this computer...
I have all the latest drivers.
And windows/ nero 9 can't use my dvd drive to burn files.
Some info about my system: AMD X4 630 CPU. MSI KA780G (AMD 780G chipset) mobo. I have 2 sata hdds, non raid mode. The DVD drive is IDE. 4gb ram ddr2 ram. windows 7 64 bit.
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
View 5 Replies View Related