Setting To Non-RAID Will Erase Disk?
Feb 3, 2013If I set a SSD drive to "Non-Raid" from RAID will it erase the disk? The SSD has all my stuff on it windows 7, the works. SSD won't boot b/c it says it's part of RAID and it's not.
View 8 RepliesIf I set a SSD drive to "Non-Raid" from RAID will it erase the disk? The SSD has all my stuff on it windows 7, the works. SSD won't boot b/c it says it's part of RAID and it's not.
View 8 RepliesI format a write-once disc (UDF format) but it write something to it (about 137 MB) so when i try to create a system repair disc it says 'disk is not blank- erase disc', but as it is a DVD+R i cannnot erase anything on it.What does Windows write to the Disk?
View 1 Replies View RelatedAs part of the chipset driver installation, it also installed the RAID and SATA drivers that Nvidia provides.I have a 300GB HDD on the primary IDE channel although I currently boot from one of my SATA hdd's.How would I go about transferring my OS to a RAID 0?Would it be possible to just system image my current OS onto the IDE drive and then format my two SATA hdd's, enable RAID in BIOS and then use Seagate Disc Wizard to install the system image onto the RAID 0?Is seagate disc wizard capable of transferring to a RAID drive??Have the RAID drivers definitely been installed with the Chipset drivers and will Windows recognise the RAID array?Have heard that you have to set up a boot partition the same size as the image on the RAID 0, would it then be possible to expand that to use the entire RAID partition
View 4 Replies View RelatedI just changed my disk setup from:
1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
My system is configured with a SSD drive for my Windows 7 x64 Partition (C:) and I setup two 500 GB drives in a RAID 0 config (Z:) to host only game installations. One of the hard drives suffered a heart attack (I can only assume as there was no warning signs) therefore wiping out my games partition (all my saves are backed up to a remote location). Now, I'm trying to re-do my raid setup with a new drive, but when I try installing Steam (it's an .MSI file), it tells me that: "Error 1327.nvalid Drive Z:" and crashes prematurely without any option to specify another point of installation, the same happens when I try to uninstall via "Programs and Features" in the Control Panel. Now, I have quite a few games that are still showing up, and I get the error "Ble bla blah no longer exists or
View 1 Replies View RelatedI recently upgraded my computer and part of the plan was to use two 2Tb drives in a raid setup for my main windows drive. I see that it only recognises about half of the raid volume and the rest is unallocated space. Is this a general limit on Windows or is there a work around this?
View 4 Replies View RelatedSetup 4 disks on a windows 7 PRO unit using the disk manager raid utility. Created a JBOD. On re-boot, all drives are reflecting a failed message.
View 1 Replies View Related1)You have two hard drives in your PC. Drive A contains Windows installation and other files. Drive B is an empty drive. Your Motherboard supports RAID 1(additionally 0 and 5) and you want to setup hardware RAID 1. Is it possible to switch HDD to RAID mode, enter RAID BIOS, create array using drive A, copy drive B content to drive A and run RAID 1 using two drives(drive A should rebuild array on next restart and copy mirror drive A on drive B)
2)You have two drives, drive A and drive B running in hardware RAID 1. You need to format drive B, copy drive A's content oto drive B(which should be non-raid drive now) and install non-raid drive B on another PC.
3)You have three drive A, B, C. Drive C contains Windows and other files. You need to setup RAID 1 using drive A and B and then copy Windows from drive C to newly created array consisting of drive A and B.
All three scenarios require no Windows re-installation.
How do I set Windows 7's Recycle Bin to automatically have a default disk space allocation for deleted files from external hard drives and TrueCrypt-mounted volumes?I remember in Windows XP, I can set a percentage of total disk space that will automatically used as storage capacity for deleted files by the Recycle Bin, and this will be to all external HDs or TC-mounted volumes.Windows 7 defaults to the 'Don't move files to the Recycle Bin. Remove files immediately when deleted' setting for newly mounted external HDs and TC mounted volumes. Since I am expecting deleted files to go to the Recycle Bin, sometimes this causes an 'Oops' when I delete files in external hard drives or TC mounted volumes, as Windows does not move deleted files to the Recycle Bin, but just deletes the files permanently.
View 1 Replies View RelatedInstalled a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies View RelatedI need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies View RelatedI had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
View 4 Replies View RelatedI have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
Which configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
View 1 Replies View RelatedI have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
View 1 Replies View RelatedI have an Asus Eee PC 1005-PE netbook. After dealing with Win7 Starter for a while, I formatted the drive and installed Ubuntu instead. But I decided I needed Windows still, so I dual-booted Windows 7 Pro and Ubuntu, since I get a Win7 Pro key for free from my university. I'm trying to sell the netbook now, and I want to erase my data but keep the OS (I don't need to keep Ubuntu on it, just Windows). I would just erase the whole disk and re-install the OS, but I don't have the product key anymore, and product-key retrievals I've tried haven't been able to give it to me for some reason.
View 2 Replies View RelatedThe erase a cd/dvd in windows 7 pro doesn't seem to work for me. So I use a program called "erase dvd". After erasing with this program I go to "computer" and right click on DVD. Then I right click on properties. Most of the time it shows as not having erased the dvd. By shutting down the computer and restarting I then get the correct figures.
View 3 Replies View Relatedsoftware that will erase a SSD, need it to fully erase and not a low level format.
Interested to know what success people have had with what software, if there are any open source softwares that do this job.
how do i format my c drive
View 2 Replies View Relatedanyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
I copied some files from a DVD that was having some reading errors to my pendrive. Somehow, a few files have strange characters at the end of the file name. I cannot rename or erase this files from my pendrive. Each time I try, I have this error message: "The file name you specified is not valid or too long. Specify a different name."
View 6 Replies View RelatedI've got a 3TB HDD. So far I had it in my desktop(Win 7 Ultimate 64bit). I made backup copies of my dvd collection on it. Now.I decided to move the HDD to a Sahrkoon mobile rack. I pluged the rack into my laptop (Win 7 Home premium 64bit). It did not show up in the explorer and it asked for initialisation. On the first screen it asked to choose from MBR and GTP as it was a brand new HDD. I chose GTP as I did befor, but still did not show up in the explorer, it wants me to create a new volume. I did not do that.
So here are my queations:
Did I erase my data by doing this?
How can I get them back and make my laptop see my hdd?
Is it recommended to use the Secure Erase, often ? Once in 2 months ?Before i do the Fw update, should i Secure Erase ?i want to make a fresh install of Windows 7, today. Should i use Secure Erase before that, or not ?
View 3 Replies View Relatedneed to do above.
View 2 Replies View RelatedHow do I erase music from a CD/RW on Windows 7 Home?
View 2 Replies View RelatedI as given an acer 5532 aspire laptop but it is password protected. How do I erase everything on it without the disk and password
View 2 Replies View RelatedOne of my computers has a virus. I want to erase all the information from that computer (computer A) and replace it with the information from my other computer (computer B) is this possible. They both run windows 7 but they are two different computers...
View 2 Replies View Relatedhow do u erase cookies in Opera brwoser?i opened preferences, a list of cookies are saved.
View 6 Replies View RelatedI have a failed hard drive that I'd like to send back to get replaced but obviously want all my data wiped first. The problem is that the drive has failed so miserably that it won't even mount to any system in order to perform any sort of wiping. I've connected it to my system directly, via a USB to IDE adapter, and via an eSATA adapter in both Windows and Linux to no avail. Sometimes it will show up in the Device Manager under Hard Drives, but that's as far as it gets - it's never assigned a letter and doesn't show up in Disk Manager. It doesn't show up in Ubuntu when I perform an fdisk either so I can't perform a DD.
This is a bit of a catch 22 as the hard drive has failed to the point where it can't be read, but I'm not sure what measures are going to be employed to attempt to validate and read the data at the manufacturer when they test it for failure. If the drive all of a sudden starts working, there is too much personal data on there for me to just hope doesn't turn up.
memory cared in my digital camera.
View 1 Replies View RelatedI have a tosiba laptop L755-5256 with no OS and need to erase hard drive completely first. then I need to flash bios from a 3.5 to 3.6 to set up for a new OS install.
View 1 Replies View Related