Hard Drive Not Being Recognized Acer 6930?
Jun 8, 2012
here recently my acer 7552-6061 laptops hard drive went bad, and i swapped the hard drive out of my 6930 to check and see if that was truely the problem with my 7552g. It was the problem, so i ordered a new hdd for the 7552g. When i went to install the hdd back in my 6930, it would not recognize it.
I've tried:
Resetting cmos by jumping G1/G2
Switching from IDE/AHCI controllers
Removing and reinstalling ram/hdd
Downloading AHCI controller drivers from acer support ( which are not "compatible" with any hardware on the PC)
The HDD is not recognized in BIOS nor windows 7 setup. Also, BIOS takes a little longer to get passed now ( roughly 1-2mins compared to nearly instant before.)
View 22 Replies
ADVERTISEMENT
Dec 29, 2009
I have an Acer Aspire T630 Series Desktop with an Uli Sata/Raid Controller (M1573). When I try to install Windows 7 64-bit it will not recognize my Hard Drive. Can any one help?
View 3 Replies
View Related
Apr 1, 2011
i am having a problem with my acer aspire 6930 i think my hdd crashed recently, here is what happened i pressed power and the machine would not load to windows and with further check the hdd was not coming u in the bios so i replaced the hdd with a seagate 500gb sata, now this hdd is read just fine in the bios, i do to boot from cd and try installing windows 7, at first it looked like all was well until it passed over an hour and the install was nowhere near finished anyway this took 3+ hours and when it is rebooting to complete the installation, after it boots pass the bios it goes to a blank screen with a blinking line at the upper left of the screen, 5 mins after the line stops blinking 10 mins later it says starting windows 5-10 mins later the animated windows icon comes then that takes anther 20 mins to boot to the home screen, now i know this is not normal but cannot get any advise about it and i am forced to believe the motherboard may be faulty but i need advise in case i am missing something
View 4 Replies
View Related
Aug 14, 2012
I have a serious USB ports problem because the system cannot update the drivers for the 7 usb ports and this is the message I have been receiving for the 8 ports in MY nOTEBOOK COMPUTER;Windows cannot initialised the driver of the hardware" Code 37.Windows ne peut pas initialiser le pilote de périphérique de ce matériel. (Code 37)
View 1 Replies
View Related
Nov 28, 2011
After removing a virus, my 3rd hard drive is no longer being recognize. Myapologies if this should be in hardware, but I didn't know if it was something that had to do with windows 7The virus was anti-virus protection 2011.I used antizeroaccess, stopzilla,avg(which is my normal antivirus), malwarebytes, and kaperskyYes all of them. It was a nasty virus.My main hard drive c: shows up as well as my second drive. e:. My other drive used to show up as well as f: but since all of this it hasn't. Nothing else was changed besides resetting the cmos battery and a couple of disconnect reconnections, becasue the drive wasn't showing up.Ide channel 0 master and Ide channel 0 slave (set to cable select). are the 2 hd'sIde channel 4 is a disk drive.The 3rd HD is also set to cable select. but that shouldn't matter cause that's what it was set to before.I also tried another spare hard drive I had with the same connections as the 3rd hard drive ( marked as slave and cable select). It was not found either.not in my computer or in bios
View 9 Replies
View Related
May 23, 2009
I have THREE Hard Drives.
1) XP. Old PATA hard drive
2) Windows 7 SATA
3) New Hard Drive (E; with program files, back up, images, music.
Sorry, I had to edit this message as every time I went to type E colon, slash, it gave a smiley face. so the E; = E colon, slash to indicate E assigned hard drive letter, the new hard drive.
When I boot to XP with the new hard drive (E; shows up fine.
When I disconnect XP and boot to Windows 7, the new hard drive (E; shows that it installs fine (lower right in windows, shows that the OS see's it and says it installed fine), yet I cannot see it.
The configuration that does not work is two (2) SATA drives, one with Windows 7, the other, the new hard drive.
To be sure, I disconnected the Windows 7, connected XP (PATA) and booted again, sure enough, the new hard drive (E; is fine and shows up.
I then disconnect and attach the Windows 7 hard drive with the new hard drive, (I even tried moving the SATA cable around) and Windows 7 boots fine, shows me that it installs the newly found hard drive (E; but does not show up on my computer.
Now, here is what may, or may not be a bug.
The new hard drive was formatted NTFS in WINDOWS XP, the drive letter assigned was E:, when I boot to Windows 7, I have a Virtual Clone Drive which also has the letter E: assigned to it. Could it be possible that Windows 7 does not know what to do since the Virtual Hard Drive was there first and therefore, doesn't show the new hard drive when running Windows 7?
I have tried everything I can to get it to be seen in Win 7 to no avail. Again, it works fine in XP, but does not show up in Windows 7.
Has anyone heard of this problem before? Do I need to rename, or assigned a different hard drive letter to E:? If so, how do I do that?
View 9 Replies
View Related
Apr 25, 2011
I have two hard drives; an older 20gb hard drive that is was forced to use to install Windows 7 and a 1tb Seagate Constellation ES ST31000424SS SAS hdd. Neither my bios nor the disk manager in Windows 7 are recognizing the 1tb drive. I have checked and rechecked the connections and power and both seem fine. In all my computer has in it:
-Gigabyte GA-X58A-UD3R mother board
-8 gigs of ram
-an i7 quadcore bloomfield processor
-nvidia quadro workstation graphics card
This is my first build but i have been looking for some time at different threads and i can not find a solution to the problem. The Constellation is an SAS drive that I'm using a converter cable to change into SATA connections. The url for the converter is: [URL]
View 5 Replies
View Related
Jan 4, 2012
Attached an external sata hd with an esata connection. After power boot, external drive not recognized and also secondary internal sata hd not recognized.
Do I need to do something to the BIOS?Sinch stonooka has chosen the best answer to his/her question.Click here to view the answer that was selected.
View 5 Replies
View Related
Feb 26, 2011
I've been using a 1TB iOmega external hard drive with my laptop for about a month and a few days ago it stopped working and isn't being recognised, the power light comes on when i connect the usb cable to the laptop but there is no noise from the hard drive at all and it doesn't show in disk management.
I took it into work with me and connected to my work PC (which runs XP) and it works fine, also tried it on another laptop which is running Vista and it doesn't work.
Laptop is an HP Pavilion DV6
View 5 Replies
View Related
Jul 1, 2011
I have an external hard drive, and a lot of data saved on it. My laptop recognises it, but i can't access it. When i go to device manager and try intialize, it says it is not ready.
View 3 Replies
View Related
Aug 24, 2011
my external Seagate hard drive is no longer being recognized by my system. The information on this is absolutely critical to me- I am a DJ and Producer and this particular drive contains all of my song stems, acapellas, instrumentals, sample kits, and also backups of every program I use (as well as my OS backup).
I just recently moved into a new apartment and my drive worked fine before the move 2 days ago. I do not think I bumped it or damaged it (seeing as how I always put them in safe places on the go) and it is now no longer working.
View 9 Replies
View Related
Nov 15, 2011
I have a My Book Essential 1TB External. I'm on Windows 7 x64. After I updated I've been getting a lot of bugs and extreme lag. I would click on the drive in My Computer, enter my HD password and the drive would open up with all my folders, etc. But then when I wanted to drag folders from my External onto my PC hard drive it would freeze up and automatically quit? Windows would no longer show the External as attached to my computer. No matter how many times I click on the icon in the task bar for WD SmartWare, it will never come back up. I have to restart my PC everytime so I can renter the External. I then installed all WD software from the Control Panel, didn't change anything or help at all.I have no clue what to do or what has happened, but my External HD is pretty much useless right now. I have very important files on there, I need to get access to this immediately.
EDIT: Now my PC has trouble recognizing the External. I tried it on my Laptop also, it doesn't show anything. It shows up under disk management sometimes. For example it'll show up then simply disappear.
Finally after restarting my PC a bunch of times and switching USB ports back and forth, this CD DRIVE E: icon appeared for the WD UNLOCKER. Whenever I try and double click on it to open it up, the green bar appears to load as seen below, then the icon just disappears, it will not open anything. When the "CD Drive (E:) WD Unlocker appears like above, my external HD will briefly appear under DISK MANAGEMENT. It shows up then just goes away along with the E: drive icon. I don't know if the USB cable that connects the External to my PC is bad or not? My external was working an hour before all this happened, so I don't understand what is happening? Also, when I click on "Devices and Printers", an icon appears with "My Book 1130". This is what is shows.
My External does light up when plugged into my PC and turns off when removed. I can hear a ticking sound which sounds like the HD working? All these problems seemed to start after I updated to WD SmartWare 1.5.1.6. I even unistalled all the WD software. For some reason whenever I try to install "WDSmartWare_Software_Upgrader_for_Windows_1.5.1.6 " it just sits there and hangs, doesn't do anything.
View 9 Replies
View Related
Nov 17, 2011
Ok so i have like 6 laptops i wanted a bigger hard drive in my main laptop so i used clonezilla to clone the drive. Then a couple days later i am trying to put the old smaller drive in a different laptop but it will not come up in the installer. I have tried it in three different laptops same thing wont come up. but it does recognize in bios and if i plug it up in windows it does pop up and i am able to use it. Anyone have any ideas why it wont come up under the installer?
View 1 Replies
View Related
Apr 14, 2010
I have a toshiba external 200G hard drive. It was used on a Dell computer which ran Windows XP. I now have a new computer which runs windows 7. However when i connect the external hard drive to the new computer i start to experience problems with the files on there.
So there are a number of directories, my pics for example. When I click on it you can see the pics on some of the sub folders when you view via icons. Some you cannot see the pic, just shows a generic shot. When you try and open the pics / jpegs you get an error saying image not found, check 'full pathname / file' exists. The same is true for all files, docs etc
I have been able to load the same pics and docs via a cd, so it is a problem with my new pc recognising the hard drive as opposed to a problem with the files
View 4 Replies
View Related
Feb 21, 2012
iomega ego 500 gb was working fine until today and now it won't recognize the drive at all. it recognizes the partitioned cd virtual drive in it, but not the larger storage drive. I plugged it into two different computers and it is recognized and i can drag and drop files. I also plugged in a usb flash drive into the same usb port and it works...so the usb drive works. I was told to assign the drive a letter in disk management, but it doesn't even show up there.
View 2 Replies
View Related
May 17, 2009
I have a Verbatim/SmartDisk USB 2.0 Firelite external drive. The drive is recognized by the system and shows up in the Device and Printers management tool. While I can see the drive, I cannot view the data on it.
I have another external USB drive by Western Digital and it is fully recognized and accessible from Win7 RC1. The Firelite is recognized and accessible on a WinXP system. It was working on Win7 Beta.
I am running Win7 RC1
Thoughts?
View 8 Replies
View Related
Oct 22, 2009
I just installed windows 7 and noticed that my internal hard drive is being recognized as an external disk drive. Whats going on and how do i change it?
My hard drive is a TOSHIBA MK3252GSX ATA Device, my computer is an hp dv5.
View 9 Replies
View Related
Apr 7, 2011
I have an Iomega portable hard drive, which is compatible with windows 7, however, when running the Iomega Encryption Utility using the reconfiguration option to set a password for the hard drive, it told me you must format this drive before use, anyways, my windows 7 doesnt recognise it anywhere! yet before the encryption ran it did! in disk management it only shows my C drive, the Iomega showed up in my computer as a G drive but it doesnt now. Its like the computer cant see the hard drive! I read about formatting the disk but it wont give me that option when the device is plugged in.
View 9 Replies
View Related
Aug 10, 2012
and i got problem with my brothers WD external hard drive, it's not recognized in my computer, my brother says "it lost the drive letter or may be some files broken" he had some knowledge about that but we can't fix that one.
View 9 Replies
View Related
Nov 12, 2009
I recently purchased a WD Scorpio Black 320GB 2.5" HDD for my Gateway MX6920 notebook. I wanted to upgrade to this larger, faster HDD and replaced it into my notebook and attempted to install Windows 7. During setup it stopped and gave the error 0xc00000e9 for "unplugging a removable storage device such as an external USB drive ......".
I tried installing Windows XP and it gets to a blue screen to choose a Repair of Windows or a fresh install. Choosing either one returns a blue screen that says system can not find a Hard disk connected.
I put this drive into an enclosure and formatted it in another computer. Also it is recognized in BIOS. I'm running BIOS version 77.08 if relevant.
View 2 Replies
View Related
Aug 12, 2011
my computer not faund iomega hard drive
View 1 Replies
View Related
Dec 9, 2009
hard drive registers in BIOS, but not in the windows 7 Ultimate 64 bit installation screen. Any questions I will answer RIGHT away. Oh dear God please help me. I took it in to a repair shop and I think I knew more than they did and left without any substantive help (but a $40 bill ). Do I need to format the HD? Would drivers help? All the websites say everything should be compatible - no problem - but nothing here.
WD Blue 640 GB (single HDD)
AMD Phenom ii
GA-MA785GM-US2H Gigabyte motherboard
OS: Windows 7 Ultimate 64 bit
View 4 Replies
View Related
Nov 23, 2011
how can i get the simpletech external hard drive to be reconized by my computer
View 1 Replies
View Related
Dec 21, 2011
the iomega_HDD(F use to be reconized and it was droped and now it is not reconized. the ubs connection is good i tried on another divice and it was reconized. The light on the imogea_HDD(F is on when plugged in but it makes a ticking sound and it is not reconized?
View 3 Replies
View Related
Apr 7, 2012
i am gettin the msg "Windows has stopped this device because it has reported problems. (Code 43)"...
View 3 Replies
View Related
Apr 13, 2012
My Iomega external drive stopped working. One minute it was fine and the next I could not see it anymore. Tried two different laptops and neither sees it.
View 4 Replies
View Related
Apr 21, 2012
usb are not recognized and no power seen at external hard drive
View 1 Replies
View Related
May 31, 2012
my maxtor onetouch external drive is not being recognized by my computer
View 2 Replies
View Related
May 31, 2012
my maxtor onetouch external drive is not being recognized by my computer?
View 1 Replies
View Related
Jun 14, 2012
I am trying to fix a iOmega harddrive for a friend and the issue that he has is that the iOmega is not being recognized by his computer. The device has power, the disk is spinning and the led is on and stays constant, no flashing or anything. I have tried to see if the device was in Device Manager but it is not. The device is not being recognized by Windows 7 at all. No beeping noises when I plug it in or anything. I have tried multiple USB ports as well as other computers. The device just isn't being recognized.
View 1 Replies
View Related
Jul 4, 2011
I have an external Samsung 640Gb hard drive which is not showing up in Windows Explorer, even though Device Manager shows it as recognized and working properly. I am running Windows 7 Home and this is something new as when I bought the drive it showed up in Explorer. I really need this drive as all my backups and programs are on it!
View 3 Replies
View Related
