Add Another Windows 7 To Windows XP/ Windows 7 Dual Boot?
Apr 8, 2011
I bought a new computer that came with a Win 7 HP license, however I already have a copy of Win 7 Ultimate on another smaller HDD that dual boots with XP.I have copied the Win 7 HP partition to the smaller HDD that has dual boot Win 7 Ultimate / XP using EASUS Partition Manager. Then I disk copied the smaller HDD to the new larger HDD thus wiping the original contents of the HDD.So far so good, the larger HDD now has C: Windows 7 Ultimate; D: XP Pro; E: Windows 7 HP. Of course the boot manager only has entries for the C: and D: partition.I think I can use bcdedit to add another entry but I am a little confused about how to do this, I've seen examples for Win 7 and XP or Vista but not for 2 copies of Win 7. Can anyone tell me what bcdedit commands I need to run? For instance I could run "bcdedit /create {} /d "Win 7 HP" but I don't know what to put inside of the {}, I think I need a new UUID but I don't know if I should be running "bcdedit /createstore" first or something else.
dual booting windows 7 home premium x64 with linux fedora 14 on dual independantly dedicated drives. i am a college student with moderate computer (windows) knowledge but am doing software development and would like to play around with some linux for a class. i have no prior experience with linux and have minimal knowledge of operation. i am currently running windows 7 and would like to keep it as my primary os. i do not wish to share media files across drives or os's, windows does that just fine as is and i dont want to get into a third drive. my current drive is a 1tb wd black caviar hdd. it is also currently 2/3rds full and the desktop is about 6 months old so i would rather not partition the drive for a dual boot. i would think that there are some other advantages for the os's operating independantly off their own drives other than if one hdd dies i should still have the other with its os still ok. i have read some topics about RAID configs with dual boot setups with dual drives like this but am not very familiar with RAID. is there a RAID config that would be beneficial in this situation? i currently do not have a RAID card. my tower internals are not very accessible and i dont like the idea of disconnecting drives depending on which os i want to operate.
i have a new work laptop with xp sp3 on it. I want to install w7 64 bit as a dual boot, but only have 1 physical drive. i cannot remove my current installation as it is pre-build from work, but can partition the drive etc. However on trying to install w7 64 bit I get a message saying cannot install windows 7 on efi drive with mbr, not gpt. Can I do what I want without screwing up my xp installation?
I installed Windows 7 on a partitioned harddrive with vista on the other half. After the installation i have my boot menu with:Windows 7, Windows Vista, Windows vista still works but when i try and load windows 7 i get a boot error message
I have dual boot with Xp and windows 7.when i log into my Xp all the restore points being deleted from windows 7.when i check the disk management information in 7 it shows windows 7 create a logical drive with my Xp primary drive.even i am hide the drive from both windows means Xp drive from windows 7 and vice verse.So i like to unmount or remove the drive partition of windows 7 from Xp and Xp primary from windows 7.So that they dont affect each others system files with being deleted the partitions.
I installed opensuse 12.1 on dual boot along with my other windows 7 installation. Installation of opensuse is successful and i can use it. But when I tried to use windows 7 on grub, it says bootmgr is missing. I've already encountered this problem a long time ago so i tried to use bootrec /fixmbr, bootrec /rebuildbcd and bootrec /fixboot in the recovery console in the windows 7 DVD. Rebuildbcd and fixboot did not work and it said something like it cannot find my windows installation. I also tried bootrec /scanos, it returned a windows installation on D:\Windows but my windows is in drive C. I think this has something to do with me messing up the active partition in disk management a month ago but i already fixed it by setting the active partition to the system reserved partition. Only fixmbr is successful, but now i can't boot on any OS because it says: Missing operating system.I also tried bcdboot C:\Windows but it failed with a message that goes like: Failure when attempting to copy boot information..
I can't get Win 7 to boot after setting up dual boot (Ubuntu 10.10) on my GF's laptop. I'll describe the problem and everything that has been tried so far. REALLY hoping somebody has an idea, I'm getting desperate.I installed Ubuntu last night via the Live CD. Used the Live version to install alongside Windows and partition the drive, install Grub, etc. At reboot, after POST it would just go to a black screen with a flashing cursor. I could only run off the live CD. A forum member determined the Grub was trying to load from the wrong partition. We changed that and voila! Grub now loads properly. I can boot into Ubunto via Grub with zero problems. HOWEVER: when I try to boot into Win 7 from Grub, it just locks at the same flashing cursor of death screen. The 7 partition is till intact, I can see and access all the files on the 7 partition from within Ubuntu, however 7 will not boot. I have tried downloading and burning the Win 7 repair disk and doing all of the following,Running the automatic Start Up Repair - several times. All it does is remove Grub, but booting still goes to the flashing cursor and I have to reinstall Grub again to be able to do anything after POST.I have used the command prompt to run "bootsect /nt60 SYS /mbr". Has the same effect as above.I have used all the bootsec.exe /fixmbr, /fixboot, and /rebuildBCD commands. Again, all have the same effect and I have to reinstall Grub to get anywhere.I don't have an installation disk to try and just do a repair install because Asus apparently doesn't feel that I would need one of these. All I have is the recovery disks from the Asus AIRecovery application that want to just re-format the entire drive and start over. This isn't an option. It's my GF's laptop (mine gave up the ghost last week) and we both have WAY too much highly important data on here. Not to mention she would castrate me . Now from all my research the only other thing I've come across that sounds possible is that the boot flag needs to be set to a different partition. Somebody had a somewhat similar problem and it turned out the way Dell set up the system the boot flag had to be moved to a recovery partition and it worked fine. I'm wondering if Asus has something similar going on, but I can't figure out how to move the boot flag. I'm going on 12 straight hours of working on this now
I have installed a year before UBUNTU on my pc with dual boot (i.e. use either window 7 or ubuntu).the NTFS partition that contains the UBUNTU was corrupted and i wanted to take the dual boot from my PC. I used the instructions from the web site: http://www.makeuseof.com/tag/how-to-...t-environment/but the disk management tool would not let me delete the NTFS partition.Could any one help me delete the NTFS partition and use just windows 7 as the only boot. step by step help would be great.
I got windows 7 running fine for a while now and ever since my XP did not boot anymore.I was not worried to much about it since i did not need it at the time.But now i really REALY need it,See i got all my Cubase projects in there and my cubase plug-ins al setup in XP and i need to get to the projects?At first it did not do anything and using easyBCD did not help either.I cpoied ntldr and detect to the root of C: wich contains my XP and now it shows the bootscreen but hangs on a black screen.The thing is right before the bootscreen shows i see the text" invalid boot.ini" flashing by very quick.I am able to enter that winXP install in safe mode and i tried safe/vga mode as well wich works but thats all.
I have a laptop I bought a year ago on which a created a dual boot Win 7 (32bit)/Win XP SP3 install, each on a separate partition. It was my first Win 7/XP dual boot install, and my first personal system that I allowed to have a Win 7 install on it at all, so although I have plenty of experience working on pretty much every previous version of Windows, I have very little experience with Win 7 and dual boot configs.
Today about 2 hours ago my audio spontaneously stopped worked for no good reason, so after shutting down each program to see if that cured it (which it didn't), I restarted the system. Out of the blue, for the first time I've ever experienced it, I received the msg "MBR Error 1" - Press any key to boot from floppy. I don't have a floppy of course on my laptop, and if I press any key I simply get the same msg. I turned the system off for a few minutes to make sure it was a good cold boot, but every time I still get the same msg. I tried switching the BIOS setting from IDE to AHCI (IDE is required for XP to boot, AHCI required for Win 7), but I still get the same error msg before I'm even prompted with the OS boot selection, so it made no difference of course.
I looked up this issue and found various suggestions, but none of the ones I found took into consideration a dual boot config., they were all Win 7 specific solutions. I don't what to try and repair the MBR only to have it screw up my dual boot config and be unable to access XP, which is what I use almost exclusively, nor do i want to lose access to Win 7 if at all possible.
I had a backup HD of my complete system that I saved several months ago when I upgraded my HD, and I periodically refresh the most important files on it, so I'm currently running on the laptop in question using my old HD, and it's working just fine. Worst case I can just clone my old HD to my newer HD that's screwed up, but I'll still lose a lot of changes I've made to the OS since I upgraded the HD and have to reinstall and config a number of programs, so that's my last option. I'll also have to back up about 200GB of data from the newer HD which is much larger than my old HD, and then restore it back after the clone, something that will take a lot of time and unncessary effort if I can just fix the MBR.
I had Win XP on 1 HDD & installed Win 7 on a different HDD. I think I accidentally did a dual boot install because Win 7 won't boot without the the XP disk connected to the motherboard.
That was fine until my XP drive died yesterday. Now Win 7 won't boot. The first time I tried to repair, Win 7 was not even seen. so I booted into diskpart and made the partition active. Now it could be seen as an OS.
Then I did a startup repair. It did whatever it does & when it was finished I restarted the pc but it didn't boot I went back to diskpart and confirmed the partition was active. I went back startup repair and tried again.
This time it said it could not detect a problem, but it still will not boot. What else can I do? My pc is homebuilt. Right now I have the 1 sata drive, 2.53 ghz cpu, 4gb ram, onboard video & sound
I lost access to my windows 7 drive (Dual-boot windows 7 & Ubuntu). every time I try to run Windows 7 I get the message: Bootmgr is compressed, Press CTRL_ALT-DEL to restart. I could run Bootrec /fixmbr or diskpart or attrib to rebuild my mbr table through DOS command window using my windows 7 recovery CD. The problem I cannot access drive C: where my windows 7 are. I get the error message: Cannot open volume for direct access or system cannot find the drive path or specified. I still can access all my windows folders and files through home folder in Ubuntu. I don't want to reformat and reinstall windows. Is there is a way to run the DOS commands within Ubuntu
Hi everyone. I installed Windows 8 today. I did partition the disk like in a guide, however, I missed where to install...I downloaded a Windows 7 iso image today and burned it to a disk, will I be able to install Windows 7 again from a disc? I still have Windows.old folder in my C drive, is there any way to dual boot Win8 and Windows 7?
I have two SATA hard disks on my Dell Precision 690. I had Windows XP (x64) pre-installed in first disk. Recently I installed Windows 7 in the other disk. The Windows 7 works well and I get options to log into either Windows at startup. But I curiously observe that I cannot VPN to my employer from that Windows 7 installation.Also, I installed LogMein and that too is blocked. I have installed VMWare on the Windows 7 and I could perfectly run VPN and LogMein from that VMWare installation. I have tried hundreds of advises and settings in the Services section to no avail. I even cleaned the Windows 7 install and started afresh; still cannot log to VPN
I have a install of Windows 7 on my computer which I am not willing to remove and reinstall. I would like to try out the Windows 8 developer trials, it seems logical given my situation to dual boot, allowing me to keep my current install and test Windows 8 simultaneously. I have a spare 80gb hard drive I could use, or I could create a partition on one of my existing hard drives, but a partition is much less ideal. I have tried dual booting linux on the hard drive before, but the linux drive over rode my dual boot set up (I obviously did something wrong), and I could only boot to linux.
How can I safely dual boot Windows 8 on this hard drive (or a partition if necessary), while keeping my Windows 7 install and data in-tact? Just to let you know I have over a TB of data spread over 2 drives but only 2 TB of hard drive space, so I can't back up a lot of my data, just a heads up.
I've got Winxp media centre NTFS installed and I've used Casper [URL] to copy Windows 7 premium from another hard drive to the Winxp hard drive NTFS partition.Do I activate the Windows 7 on the Winxp hard drive ? Will it cause problems ? The hard drive Windows 7 is installed on is a used hard drive .I don't want to dual boot with 2 hard drives.I've also downloaded EasyBCD.
I need to have win2k on my computer (hp dv7 win7 GR) which is the best way to go meaning stable system and proper operation. I have tried a virtual pc but it made a mesh wile I was trying to install my ethernet plotter, scanner, printer, and some programs that require a usb key to work.
I wanted to dual boot Mac OS with my Windows 7 but everything I do it comes wrong, simply doesn't work. I tried dual boot with iatkos v1.0i, iatkos s3, iatkos v7 but still nothing.
i have a hard disk 500gb and i made three partitions.the 1st partition i installed windows 7 first.what i did today?i wanted to install windows xp to the 2nd partition.i installed and now that is the biggest problem.i cant in to windows 7 anymore.when i turn on my pc it has only windows xp.it hasnt dual boot to choose what operation system i want to in.so what to do?i want windows 7 and xp with dual boot to choose
I tried to make a dual boot with windows 7 and windows 8, but when I made a partition, the hard disk drive (C changed to dynamic.Can I still upgrade to windows 8?how can I convert it back to basic disk?I have windows 7.
I had Windows 7 installed on my PC. Today I installed Windows XP in another partition. But now when I restart my PC I don't get a DUAL BOOT mode screen. It automatically logs in XP. How do I log in WINDOWS 7 now?
A friend of mine made a dual boot system on my laptop. The problem is it loads windows 7 without going to the boot manager screen to allow me to choose which one i want. My laptop came with xp and it shows that the hard drive has been split. And it also doesn't have the recovery in the laptop.
I recently purchased a pc that has Windows 7 on it. (2.6ghz and 4gb of ram). I have an old pc that is currently running XP. What I would like to do is move my XP drive over to my new pc and be able to dual boot both OS's but I am not sure what I need to do. Will simply plugging in my 2nd drive be sufficient or are there changes I need to make such as in the BIOS, etc?
I am using Windows7 Ultimate x64 on a Notebook computer and so far OK. However, a network program came from government can run only on x32 of Windows. So that I am planning to have dual boot system now. I am wondering what will happen on my account and local mail-box.I have Windows 7 x64 on C drive and D drive is prepared for Windows 7 x32.
Q1: C drive has /users directory and my account info is there. What will happen on this directory if I install Windows 7 x32 with same user name and same password?
Q2: I am using Thunderbird with IMAP server. Can I use same mail-box both from Win x64 and Win 7 x32 time to time? I have moved most of mail to Localfolder.
I have win 7 installed in my PC on C: drive. I have a empty D:drive with 102 GB of space, in where I wish to install Windows XP. But during the installation process I came across with a error " setup could not find any hard disk". Upon research I find that SATA controllers in new computers doesn't support XP installation. In one of the forums they suggested to change SATA module in BIOS to modify from AHCI to ATA. When I try to do that it popped a statement " cache flash module" has to be disabled. I disabled it and modified the AHCI to ATA , which resulted in another pop up saying that " these setting changes will result in reinstallion of existing operating system" . procedure where i can install XP into D:drive without loosing the existing operating system.
I'm planning a bit of an upgrade of my Windows 7 running machine (see spec).
What I hope to do is install a second internal hard disk drive and run Windows XP Home Edition from that, while running Windows 7 on the original HDD, dual boot.
What I would like to know is: Is it possible to run a dual-boot system from two separate HDD? What's the best size and brand of HDD to choose?
I have a Lenovo Z575 with a AMD A6-3400M APU processor and 6 gb of RAM, I am running Windows 7. My Question is Is there a way to create a dual boot with my setup With Windows 7 as the default OS and Mac OS as a secondary OS?
If I make a partition on my 500gb hdd (D for example) and format it as HFS+ and then change my BIOS settings so that D boots before my main C drive which is currently running Windows 7, and pop in an install disk for Mac OS X will it install normally with the .dmg file format? Or will I still have to find a way to convert the .dmg file still? I would like to have my computer dual booted so I can run either OS at any given time.
