AMD Manufacturer That Makes Solid Video Cards?
Dec 6, 2011
I'm looking to buy a AMD Radeon 6950, 6970 that's 10.4 inches in length or lower.I recently purchased a Sapphire Radeon HD 6950 Dirt3 addition to replace my Crossfire setup of HIS Radeon HD 5770 cards.The card ran great for a day, and then I noticed artifact tearing and constant crashing to blue screen was an immediate sign the card was bad. But I gave it the benefit of the doubt, went to safe mode, disabled the card, uninstalled the old AMd drivers, swiped the registry for AMD video clean and reinstalled drivers. Still same artifacts and crashing. So I turned off PC, reseated the card, and still same issues.I had to RMA the card, and unfortunately Newegg doesn't have it in stock anymore (I figured these cards were good because they're out of STOCK everywhere.) so it's likely by the time it;'s finished processing I'll get my refund. Because if the item is out of stocked I have two options, replaced with a product of "equal" value, or refund. I'll obviously opt for a refund though.
Windows 7 pro 64 bit
AMD Phenom II X4 925 @ 2.8ghz
4GB DDR3 Dual-Channel 1600mhz
Gigabyte GA-MA785GT-UD3H Mobo AM3 soc
HIS Radeon 5770 Crossfire setup
Thermaltake Toughpower Grand 1200w 80+ gold certified
View 9 Replies
ADVERTISEMENT
Dec 17, 2012
I'm looking for software that can do one of two things. It can either take a directory full of photos and videos and play them in a slideshow type loop, or can combine photos and video in a single file, movie, .exe, etc for playback on a computer connected to a TV for a trade show. I'd also prefer free, if possible.
We have a week long trade show coming up, and would like to put new photos and videos in a directory each night, and have the software start to play all of the content, like a slideshow, in a continuous loop. Then, each night, we could stop the software, update the content, then restart it...or replace the single movie file or exe with an updated one.
View 3 Replies
View Related
Jun 5, 2012
Is it possible to put a Nvidea GTX 560 + Nvidea GTX 670 in one pc, and get them work both with one monitor?
View 7 Replies
View Related
Nov 29, 2011
I built a HTPC with a video card that does DVI and hdmi. The motherboard has a VGA.
But I also need either: s-video or composite What should I do? I don't want to like "downgrade" the video card and just use an old one for everything. Can I run them both? Like switch back and forth? "Simultaneous" is not required.
Also, I would already be using the PCIE 2.0x16 for the video card. I have PCIEx1 and PCI slots open. EDIT: I found this... [URL]
Would this work in letting me switch between the onboard video and the video card?
View 1 Replies
View Related
Oct 23, 2012
I have an old HP Proliant PC that I upgraded to Windows 7 Professional. There are only two PCI-X slots (one half height and the other full height). This is not PCI-Express or plain PCI.i need to add a video card to support a higher resolution monitor. There is an ATI Radeon 9200 PCI-X card out there, but it is not supported with Windows 7. Since this card type is more than 10 years old and operating systems have moved on, I need to know where to find a new PCI-X graphics card (or used) that will support higher resolution. If a standard PCI card will fit in the slot, will it work and what is the down side.no drivers for Windows 7 with PCI-X.
View 4 Replies
View Related
Nov 10, 2009
I have a ATI Radeon HD 4800 that I use with DVI for my main display. I recently installed a Radeon 7500 PCI with the sole purpose of using the S-Video output to stream video to my TV. Under the device Manager I get the following error with the new card
PCI bus 7, device 1, function 0
"This device cannot find enough free resources that it can use. (Code 12)
If you want to use this device, you will need to disable one of the other devices on this system."
What can be going on?
View 5 Replies
View Related
Jan 5, 2010
I recently built a new machine that I have three monitors for. When I only had two monitors I had this card installed: Newegg.com - PNY XLR8 VCG98GTEE5XEB GeForce 9800 GT EE 512MB 256-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI Supported Video Card - Desktop Graphics / Video Cards
This card works perfectly fine and I had no issues with it and I plan to continue using it. However, now that I have three monitors and I need another video card I'm running into a lot of issues. I tried installing another PCIe 16 card I had lying around but my setup didn't seem to recognize the new card. I do not have the exact model number on that since it was given to me, but I believe it was a GeForce 6 series card. I also tried a PCI ATI Radeon card that I had laying around found here Newegg.com - SAPPHIRE 100945L-BK Radeon 7000 64MB 64-bit DDR PCI Video Card - Desktop Graphics / Video Cards
This card showed up in the device manager as a Standard VGA adapater but in the properties it had an error saying "The device could not start".
So I guess my question is this: What is the cheapest way to get three monitors working on my windows 7 64 bit machine? I want to use the first card I linked to and one other one.
Would this card work? [URL] - PNY VCG84512SPEB GeForce 8400 GS 512MB 64-bit GDDR2 PCI Video Card - Desktop Graphics / Video Cards
Here is my motherboard in case that'll help: ASRock > Products > M3A780GXH/128M
View 9 Replies
View Related
Aug 16, 2012
I plan on getting a Nvidia GTX 570, but I don't know whether I should get two or one, because my motherboard runs one at x16, and two at x8.
View 2 Replies
View Related
Jan 7, 2012
I have a HP Pavilion DV7T. It came with 2 video cards, an intel integrated card to save battery life, and Radeon card for games. The problem is, when running Skyrim the game looks for the video card listed in DirectX. My Radeon card is working, but not showing up in the dxdiag. How to get the Radeon card, or both, to show up on the dxdiag? I have uninstalled and re-installed the card. I have the most recent drivers, and tried older ones. Both cards show up in the Device Manager, the integrated card is listed first.
View 2 Replies
View Related
Aug 28, 2012
i have a question. i am running a quad screen set-up. i have been running windows 7 32-bit. with 2 video cards1 pci-e ati radeon hd 4350 now it was working great in windows 7 32-bit, but ever since i upgraded to windows 7-64 bit. its not working at 100%now i have been reading alot on this forum that alot of people have trouble getting the fx 5200 working. after trying many different drivers i finally was able to get it working. the only catch is that. i had to turn off aero and disable other aero features so it can run with better performance.but even after doing that. the ony problem i have is that videos such as in Internet. run slow seem to lag a little and worse when i put it on full screen.i figure its the card because its so old and its a pci card
View 5 Replies
View Related
Oct 28, 2009
I have two different ATI cards installed in one system, each with their own 22" HP LCD. One is an ATI FireGL V5600 for my CAD applications and the other is an X1900XT for Left4Dead. When I ran Windows Update after I installed Windows 7, it immediately downloaded an updated driver for the V5600 (8.623, I think) but when it installed it, it disabled the X1900XT.
I went to the Device Manager, uninstalled the X1900XT, then Scanned for Hardware Changes, it finds the X1900XT, installs the driver and it works again. Unfortunately, it also reverts the driver for the V5600 back to 8.56.1.15 which isn't even a valid driver for the V5600 as seen on this page.
I'm not sure why I can't have independent drivers for each card. I know for a fact that this is supported in XP as I have my system dual booting with XP and it work perfectly there (see photo 1 and photo 2 it's hard to tell, but both of those screenshots are from XP with each card having independent drivers). The downside is that my CAD apps don't recognize the V5600 with driver 8.56.1.15 as the workstation card it is, and my graphics are severely crippled in those apps.
I would like to report this to Microsoft, but unlike in RC1 there is no way to report a bug.
View 3 Replies
View Related
Nov 2, 2009
I have vhs-c format tapes whereas I want to transfer them over to Windows 7 64 bit.
Currently my software/hardware will not work. Do you know of any usb type hardware that will work with it?
View 1 Replies
View Related
Oct 11, 2009
I am looking for Windows 7 compatible video capture(tv tuner) PCI interface cards.
Can you please suggest the same?
View 3 Replies
View Related
Oct 24, 2009
i have recently come into possession of a computer with a 2.70 Ghz celeron
but it has NO agp port
could anyone recommend any pci video cards that support AREO/GLASS
ATI or Nvidia are preferd choices
im not a gamer s i dont really need anything powerful
ive tried newegg but they only have Nvidia the ATI cards are all dx8 -.-'
if i can git a variety of choices at less then $50
less then $30 would be preferred ..
View 7 Replies
View Related
May 26, 2012
I wonder if there are some AGP video card that are supported in Windows 7 32-bit?
View 6 Replies
View Related
Oct 31, 2012
My computer has a Intel(R) HD Graphics Family card. I've been having problems viewing 720HD scenes. Windows Media Player and VLC players cannot skip parts of the videos. The videos will freeze and the programs will crash after waiting a few minutes to continue the scene.
View 2 Replies
View Related
Feb 1, 2010
I know some people have been asking questions concerning 3 monitors on Windows 7, but they don't answer the question for me (i think).
My system is an ASUS P7P55D-E Pro, Core i7-860 2.8Ghz and dual GeForce GTX 275 1.7 GB.
I've spent a good couple of hours to get this to work or reading up on it, but I just have a 3rd monitor sitting here.
View 2 Replies
View Related
Sep 11, 2011
after months of trying to get my video card drivers to work with windows 7, i finally made it happen. after that happened the laptop started to be slow and laggy. there was no lag problems while the video cards weren't installed. i'm saying like Internet loads slow, so the audio plays fine and video skips constantly or freezes. scrolling and load times for the browser are skippy and very slow, respectively. i don't know what i should do about this. i have 2 nvidia 7900gs currently going with the temp. at 74c.
edit: i forgot to add, when starting up sometimes windows will freeze and i have to hold the power button to shut it off. and other times, when it's loading up the monitor shuts off and about 2 minutes later it will turn on and then windows will show up and finally load.
View 1 Replies
View Related
Nov 14, 2009
3 Viewsonic 22" monitors and one Dell 24 inch monitor all running DVI cables.
I have three of the video cards in the computer to run multiple monitors. Windows 7 has a feature where when you plug in a monitor, it auto detects it and then enables it and sets its proper screen resolution. The problem is that when I plug in more than one monitor, I get inconsistent results.
Here are some examples:
Example 1 that happens: I have two monitors plugged in and I plug in a third monitor. It enables it within Windows 7, but the monitor does not actually turn on. If I restart the computer, somtimes it will stay enabled and boot up with all three monitors on.
sometimes when I reboot it, it again shows all three enabled but only two are actually on. This happens also when I plug a fourth or fifth monitor on. Sometimes two or three monitors will be on whereas one or two others will not be on but will show enabled in display properties.
Example 2 that happens: Sometimes when I plug in a second, third, or fouth monitor, it will actually show an additional monitor as disabled. For example, if I have three monitors plugged in and it shows three monitors enabled (regardless if all three are on and working), and I plug a fourth monitor in, then it enables the fourth monitor, sometimes it turns on, sometimes it doesnt, and it also shows a "generic non-pnp monitor" as number FIVE.
Even though only four displays are plugged in. I've seen this happen even if I plug in a third monitor (shows four, with 3 or number 4 disabled). If I try to enable that FIFTH "ghost" monitor, and click apply, it says "cannot save settings." You can see an example of this as an attachment.
When I plugged in another monitor, it shrunk 2 and there is also a 5 the same size but disabled. Strangely enough, the 2 says the pnp monitor and 5 says the model number of the monitor. However, enabling 5 does not actually enable it and says that it cannot save settings.
I have tried downloading the latest drivers from ATI 9-10 as well as Catalyst Control Center as well as Hydravision from ATI and also Ultramon multiple monitor software. I have tried deleting the ATI 3600 drivers WDDM 1.0 (maybe 1.1) from device manager, only to reboot and then it installed the drivers, reboot again and it brings back all of the whacky settings.
I have a couple of times got all four monitors enabled and all four monitors on where the cursor moves across them properly. EXACTLY what I want to have happen. If I restart it almost always comes back on as EXAMPLE 1 where only two of the four monitors will turn on, but it shows them enabled in display properties, or if all four monitors do come back on, they are not in the same order that I had them in and it actually shows FIVE in display properties.
To make this all even stranger, believe it or not, i've even had it boot and one of the monitors is BLACK & WHITE. What is so strange about this is that the Windows 7 logo when booting, the color Windows 7 logo, is indeed COLOR on that screen, but once it is actually in Windows 7, it is BLACK & WHITE.
If I do a restart, it sometimes comes back in full color. What this means is that there is color while Windows is loading, and then once in Windows one of the monitors is BLACK & WHITE throwing out the possibility of a bad video card.
Has anyone else experienced anything like this? Is there KNOWN issues with Windows 7 and ATI video cards or drivers? How about Windows 7 and Viewsonic or Dell monitors? This is extremely frustrating and looking for some guidance on the subject matter. I believe that the drivers, whether Windows WDDM default or ATI's are simply not correct with Windows 7. I never had this problem with Windows XP.
PLEASE See "win7_monitors.jpg" file to see what I am talking about concerning EXAMPLE 2.
Edit: I need to add that on example 1, where it shows enabled but the monitor does not come on, I have noticed that about 50% of the time when I put the Windows 7 into SLEEP mode, and take it out, the monitor(s) that were off are now on.
View 6 Replies
View Related
Feb 27, 2011
Video from sd cards only shows black screen with audio
View 1 Replies
View Related
Oct 2, 2011
My dell inspirion 1545 keeps going to computer rpair every time i turn on my laptop. It then says it can not find problem and can not fix the problem and then when i hit finish it shuts down. when i try to go to system retore it says Parameter is incorrect and once i hit okay all i have is the windows 7 background picture and cant do anything but shut down comeputer and restart. Then computer repair starts all over again.. i do have the reinstallation disc. My computer is no longer under warranty
View 6 Replies
View Related
Aug 31, 2011
I'm having some BSOD issue, I suspect, they'd be due to some drivers stuff and all.So anyway, I saw Device manufacturers had more updated drivers then the OEM (Acer Laptop here), do you think these generic drivers are worth a try or can they be harmful?
View 7 Replies
View Related
Jun 15, 2012
After a clean install of Windows I noticed that when I right click My Computer and select properties, there is no manufacturer information as well as the logo. Under System in this window the first on the list is the system rating. I tried going through the registry and in OEMInformation there is nothing there. Strange
I have an Alienware M17X Laptop.
View 1 Replies
View Related
Jun 17, 2009
I am currently experiencing slow performance on a Windows 7 RC 7100 laptop.
I have run RadarSync and all drivers are up to date, however when I check the device manager, the following have exclamation marks;
- Mass Storage Controller
- PCI Simple Communications Controller
- Unknown Device
I am considering installing the Manufacturers Drivers for VISTA via "Troubleshoot Compatibility" mode as opposed to the Windows Supplied drivers.
View 1 Replies
View Related
Nov 27, 2011
How do I activate & validate Windows 7 using small manufacturer's COA?The COA is 14 digits as opposed to Microsoft's 25 digit product key. When I try entering this code it is immediately rejected.
View 8 Replies
View Related
May 13, 2012
I have brought graphics card from friends old computer[DESKTOP]. He lost the driver cd and cannot remember its series or manufacturer. There is a sticker on it which says: GF 9400gt 512 mb. I installed the card win 7 booted up. It detects the card as standard vga graphics adapter, device manager says device is working properly gives me 1024x780 resolution. So I tried 9 series gf driver from nvidia. It says no compatible hardware detected. NVidia auto scan same result. How can I know which card actually i am using? If it is gf 9400gt 512 mb then what is the problem with driver. In device manager hardware id is like this:
pciven_10de&dev_01dc&subsys_00000000&rev_a1
pciven_10de&dev_01dc&subsys_00000000
pciven_10de&dev_01dc&rev_a1
pciven_10de&dev_01dc
pciven_10de&dev_01dc&cc_030000
pciven_10de&dev_01dc&cc_0300
View 6 Replies
View Related
Oct 11, 2010
OK so on to my problem and question. I set my taskbar to be along the top of my monitor screen. It seems like ever since WinXP and probably before that, some windows that open creep under the taskbar. So when this happens, I have to move my taskbar in order to close the window. Yeah I know there's other ways to close this window without moving the taskbar, but another more elegant way to avoid this problem is make the taskbar solid so the window can't creep under the it
View 1 Replies
View Related
Jul 22, 2012
I have Windows 7 N Ultimate. I just bought Paragon Migrate. I tried to move os only to SSD. Although it has option of selecting other stuff to move, when i choose something, it doesn't get chosen and program just not choosing anything but OS. But this is not an issue. The issue is, when it gets to DOS after restart to finish moving os, at some point while it is moving, I get error message "Some Error occurred: Bad parameter of function". At the same time, at the top right corner it says Succeeded. When I try to boot from SSD I get strange error window saying "Windows failed to start 0xC0000034 Unexpected error.
View 2 Replies
View Related
Jan 17, 2012
This isn't recommended, I know. But would it serve any purpose at all? As far as I understand the matter, aside from the wear and tear issue, whether an SDD is 0% fragmented or 100% fragmented makes no difference to the performance, due to the way the information is read from the disc. Is that so?I run MS Flight Simulator from an SDD (my O/S is on another SDD too) and I am starting to get some performance issues. Some have recommended I defrag the disc - when I analyse it, it shows 100% fragmentation, but if what I wrote above is true, it wouldn't make any difference. Right??
View 8 Replies
View Related
Jun 13, 2012
I'm looking to install a SSD drive for my windows 7 64bit custom rig I have. Currently I have everything on a 2tb internal HDD. I'm looking to keep everything the way it is and just place my windows on the new SSD.My first thought was unplug my HDD, install SSD install fresh Windows 7 on it, change boot up in bios to SSD first, plug HDD back in and delet windows off of it. Another thought was is it possible to install new SSD and move windows folders to it from HDD?My ultimate goal is to not have to reinstall all of my programs and to keep all my current settings.... I'm looking for the most painless and easiest set up of my new SSD drive and to just have windows on it.
View 9 Replies
View Related
Jun 26, 2011
I recently was doing 'maintenance' on my network and during the process, decided to upgrade the firmware on my routers/APs. All went well except that my trusty old BEFSR41 didn't survive. I tried the known fixes, but no response.So, I'm asking for recommendations. I do have wireless covered with a WAP54G, but it may be time to update that as well.Features I want are good security (inbound and outbound MAC filtering, IP Range limiting, port limiting, etc.), speed and reliability. I'm not opposed to a wireless router with ethernet ports (at least 4), but I would like the ability to turn the wireless aspect off, since I don't use it that much (at the moment).I have several machines on site, connected to an 8 port gigabit switch, which was connected to the BEFSR41, which was connected to a cable modem. Netgear is not a preferred solution. At some point, I plan to connect my TV, if that is a consideration in choice. OK, I'm rambling now.
View 7 Replies
View Related