First, my appologies: I tried a HW group first with this question with no response. I know some folks here are knowledable about Promise RAID. I should have x-posted instead of multi-posting, but I thought I'd get an answer in the other group.Anyway...I have a mirrored setup on a Promise RAID built-in controller. One disk wentbad. I removed it. The remaining disk continues to operate normally - fornow. However, I get a "critical" warning from the RAID controller every time I boot - but it does succeed without issues.
I would like to eliminate this warning and continue with only one disk.Preferably in a single-disk non-RAID config. But, whatever.How can I do that? Do I have to rebuild from scratch? What happens if I use [ctrl-F] to enter the RAID management and simply "delete the array"? Will I be able to reconfigure to boot from that remaining disk or will it require to be rebuilt completely as a single IDE?
I have my old XP load on my C drive and Vista on the D drive. I'm ready to wipe out XP (I know lots of folks would go the other way) so I can create a mirror copy of Vista for fault tolerance. Before I enable RAID in the firmware, I'm thinking I need to format the C drive. However the Disk Management utility has the format command grayed out for the C drive. It shows up as:
Disk 0: C: NTFS, Healthy (System, Active, Primary Partition)
My D drive is: Disk 2: D: NTFS, Healthy (Boot, Page File, Crash Dump, Primary Partition)
What is the proper way to wipe out C so I can create my RAID mirror?
I am running Vista on a Dell XPS 420. I came home to find both drives failed in a RAID 1 mirror. Dell gave me no help recovering data, but did send two new drives. I have installed Vista on one of the new drives without RAID. I wanted to see if I could recover any files from the failed drives, but I can't seem to get Vista to recognize either of the old drives that were in the failed RAID array. The failed drive does appear during boot up and still shows as part of a failed array. How can I get Vista to recognize the failed drive so that I can then attempt to run file recovery software on it?
I bought a laptop HP Pavilion DV9428, AMD Turion X2 2.2GHz, 2 Gb RAM, 2 x Toshiba 120Gb HD (device manager says SCSI !) I would like to mirror my main HD to the 2nd one in the event of a HD failure. I searched in my owner's manual and in Windows help file and could not find any information on how or if it can be done.
Shortly after installing Vista SP1 I have started to get message "a drive in Raid 0 is failing". This sounds bad. I have tried running checkdisk on my hard drive but it does not show any problems. If I reinstall the OS from scratch, will it fix the problem? Or is this a hardware problem?
Just bought (should arrive in a day or so) a Lacie 2Big Dual 1T external raid drive (via eSATA). Just a quick thought, As I plan to use it in a Raid 0 set up do I need to make any adjustments to my bios or install the JMicron drivers so Vista can utilise the raid as well as my other three, non raid, sata drives. I've looked at the manual and doeesn't mention any thing about it. Or is it simply plug it in and forget.
I read there is a performance boost with raid -0, could this be true? I am interested in setting up a 4 drive riad -0 in vista anythoughts? And will VistaBusimess Disk Manager use 4 drive in raid 0.
I need to know what would be the best optition for top performance.
Raid Settings
RAID 0
128KB Strip
It said in raid settings this is for top performance. 64KB for the other not sure what it was. Also should i remove the RAID and then do a full format then low level or just leave the RAID as it is. And what should i make it RAID 0 RAID 1 or RAID 5 for performance. I'm a gamer.
I purchased a HP Media Center PC approx 16 months ago. Shortly after I purchased it I started getting what appeared to be an intermittent hard disk error - the screen would suddenly go black, system would attempt to reboot and I would get a message in the lines of "SMART FAILURE predicted... Windows detected a hard disk problem... Immediately back up your data and replace your hard disk drive. A failure may be imminent." Then it gives some options to to go to the BIOS or to continue. Sometimes I can reboot immediately (usually reboots to safe mode first, then will reboot normal), other times I need to reattempt several times before it will actually reboot (the SMART FAILURE screen pops up each reattempt). Once I am able to reboot it's pretty unpredicatable when this screen will show up again...
sometimes a day or so later, other times it would be stable for a few weeks.... the reason I was able to 'test' for a while is 1.... after the problem occurs I backed up and removed all important data from the drive and 2... since the computer was only a few months old HP was sending me a replacement warranty drive. Once I recieved the replacement drive I created an image of the original drive, copied it to the new drive and sent the 'faulty' drive back to HP. I assumed everything was fine, but the problem started occuring about 4 months later. So again, I made sure everything was backed up, created an image & contacted HP for another warranty drive. Once again, everything worked fine... for a while. Now, one year later out of the blue this 'hard drive failure is imminent' problem is popping up again...........
Well i am going to backup my C Drive incase my PC encounter failure one day. How should i do it? I cannot find the topic that teaches you how to backup anymore..
The main hard drive on my pc that has the operating system on and everything is begining to fail and i need to sort it out before i cant use the disk anymore. The disk is in warrenty so i will be able to get it replaced but not all the things on it.
How can i backup my operating system and all of the programs and files on it, i have another hard drive that i can use as a backup but im not sure how to do it.
1. Put computer to sleep. (iffy - sometimes resets resolution, 1-2 times caused harmless BSOD) 2. On wake up, computer shows distorted image and then BSODs. 3. resets to bios, but doesn't complete the bios progressbar (not sure if this is for POST) 4. Hard Drive(s) start to click.
I may be wrong, but seems like a simple case of hard drive failure, but it was directly caused by Vista, which has been known to have problems with Sleep. I don't remember checking/signing any Vista-hardware liability waiver, so is Microsoft liable for the hard drive failure since the risk was not eliminated by a critical update?
I am trying to back up to a WD Passport 250gb usb drive. Every time it fails stating file 0x80070002 cant be found. I returned the drive to the store and replaced it, but I still get the same failure. Could I have gotten 2 bad drives or is there something I can do/chnge in Vista to correct this?
went to get a new laptop and founds a nice mew Toshiba laptop (have to check model number) got the laptop home an started up fine worked fine also got thee system online and with all the anti virus set up (used the 90 day Norton trial) worked fine next day I stared the laptop up and the worked fine for a wile then went into a full crash with nothing responding forced a reboot look fine bios came up vista went to load the bar stuck and then restarted then kept doing this and no hard drive activity left the machine
and still stayed like this tried restore and start-up recovery as the pc was loading in safe mode the laptop did start the reload of the hard drive after that said was successful rebooted and did not want to load up ,took the pc back and checked the machine out they could not fix there machine the man told me the machine was not going to work and sated to fill out a Toshiba doa form stating that hard drive failure was the cause, that left me the option to change the laptop or get my money back and chose the get money back to see what i could get else were still looking I am thinking of getting a Sony vairo instead
I have 2 hard disk drives: Seagate 1000GB 7200.11 32MB Western Digital 150GB 10KRPM 16MB and two days ago, the Seagate hard drive isnt being recognized/seen by the computer. I have an Asus P5Q3 Deluxe mother board. A week before this problem I was getting alot of BSOD's and freezes, turned out to be faulty RAM, but added this in case it might help. I have never had this problem before... I unplugged and replugged the hard drive, and switched a cord that links it to the motherboard. I have also tried putting the cord into a different SATA port but it didnt work, I didnt try a diff power cord yet, but I will see if it works or not and post it PS - I'm not very computer technical or w/e, but
Think my HD may be failing. First, a few black screens have occurred on bootup. After normal shut down this A.M., it booted into the BIOS screen, after noisy boot. I simultaneously pressed Ctrl + Alt + Del expecting to get Task Manager. Got Advanced Options Menu. Pressed enter, booted to Windows normally. And just now, got louder than usual "whirring" noise on bootup, which went on to boot into Windows normally.
Question is: What would my options be if the Drive totally fails? I've got Personal Data saved. And all I have is Recovery Disks for this laptop. Would those be able to be installed on a new Drive if needed. I'm under the impression that I have a Smart Drive. Wouldn't that warn me if the Drive was failing? No warnings yet! And what type of Warning should I look for? So, how should I prepare for HD failure?
I thought I had been able to make a backup of a Vista Ultimate System on a Raid0 array (C: partition using the standalone Acronis True Image 10 boot disk) and copy it back to a non-Raid disk. For some reason Vista will not boot correctly and the Vista boot disk Repair Option thinks about it for 5 minutes or so and then says it can't fix the problem. I know I have done this trick with WinXP and I thought I had done it with Vista. I know I can do the save/restore routine (Raid0 to Raid0) with the Acronis standalone software. what I have to do to get a Raid0 version of Vista Ultimate transferred to a non-Raid disk using all the same hardware.
I have the Vista Ultimate System on a network so I can backup to a different controller and hard drive, delete the array, reformat using Partition Magic 8.0 and restore. The only reason I am trying to do this trick is because the SATA controller on the motherboard does not support Raid Arrays and SATA DVD Drives together...and...I want to install multiple SATA DVD Drives on this system.
i was on Internet earlier today when i noticed that the videos were already completed buferring, but the videos were lagging; and firefox was performing kind of slow. i decided to re-start my computer. after re-starting the computer the logon process took extremely long, then an error message appeared: logon process has failed to create the security options dialog. failure - security options. i waited for the desktop to appear, then re-started again. but the perofrmance of the logon is still extremely slow. any suggestions?
I just installed Vista Ultimate (64-Bit) on my Qosmio G35-AV660. Problem is this, it is now seeing both my HDDs as one in a "Logical Drive 0" and "RAID-0" array. Instead of 2-120gb drives I now have one 214gb drive. I want to return to separate HDDs "C" "D" w/out RAID. I have tried booting from the Vista installation disc, and when it asks for raid driver, I install and it still only shows the "one" drive and not separate drives.
I also went into the bios screen at start up and it shows the separate drives with same RAID array, and wasn't able to change it. I tried the changes available, but it continues to reset itself and boot normally. I understand I will need to reinstall the os after RAID is removed. If I remove the second drive while doing a clean install, will it force it back to non raid, and then I can reinstall the second drive after the new install? Or is there a better way?
I'm have a couple of problems and I was hoping someone here could help with the solutions.
I wanted to use a raid setup with vista ultimate x64. But I had problems with my raid bios. I went ahead and installed and activated vista any way in a non raid configuration. Now that I have my raid bios issues fixed I would like to setup my raid array. The problems and questions I have are:
1. I didn't realize it but I left the bios setting for my sata set to raid. I don't have the raid set up just the setting at raid. When I change it to ahci vista won't startup and my machine reboots. If I don't want to or can't do the raid array how do I fix this? Since I've already activated vista can I reinstall it? I believe I did install the raid driver at install time.
2. If I do want to do the raid array can I do that with vista already installed on one of the drives?
I'm currently running a non-RAID setup but for convenience would like to set up a RAID 1. My C: drive is 1TB and it contains my OS and all my media files. Currently I manually back up my music and video files on a couple other dissimilar sized hard drives. Since I get new music and movies fairly frequently, the backup process is fairly tedious so I thought RAID 1 would be useful. If I went to RAID 1 could I simply add another 1TB HD and would all my data automatically copy? Or would I basically have to back up all my data from the 1TB drive, reformat, add the new drive, and perform a fresh Vista install with RAID 1 enabled, then copy everything from the backup drives to the RAID 1 array?
I have a set up with RAID 0. I want to install Ubuntu on an external drive. I have read a post in the Ubuntu forums about disconnecting all internal hard drives and only using the attached external drive to install the OS. My question is if I disconnect the RAID-ed drives, will the RAID remain intact after the external drive OS install and the reconnection of the RAID-ed drives? Or will I damage the RAID and have to reinstall my Windows OS?
System specs: ASUS M2A-VM mobo, Athlon 64x2 5400, ATI RAID utility, Vista Home Premium x64, Catalyst 8.9
I don't kno all that much about HD drives and RAID.. I'm not sure what to do here, but I have my main HD in my new system.. it's a 500GB Seagate Cuda the 32mb Cache 7200.(11) version.. it's a pretty good HD I've read. and currently just plugged in.. no special way or RAID setting or anything. I also have my old computers 250GB HD in here. I moved everything over from my old PC.. and just been lazy and have not taken the 250GB out.. well now I'm going to take it out.. and sell that computer... and from a freind I'm getting a deal on a 250GB HD..
So my question is what can I do with it.. What advantages can I get with using RAID 0 or 1 or whatever. it's a 250GB Spinpoint Drive. I don't kno what RAIDS all about.. how much performance will I gain with it.. whats the best way to hook it all up? I want to have my stuff backed up.. not everything. but the important stuff thats on my 500 I want to have on this new 250 I'm getting.
My pc was configured in raid5 but I lost all the data. Since then I decided to go back to the classic drive C,D,E each by themselves. The point is that things are going slow / sometimes I try to access drive D with music and there is a significant latency in the hdd response. I can even hear the sleepy drive waking up. I might want to aim to high but here is what I dream to do.
1. I want to go back to a raid configuration in which all those hdd(i have 3x 500 sata) to work hard for me. 2. Find a way to add the fourth one in which to save important data. I case of crash to reinstall vista and all the soft without losing all my projects. I am doing video editing.
My motherboard has a sata external connector. What would you guys do with this configuration in order to set up a raid. Don t tell me trash it 'cause i won t. I paid more than 4000 bucks last year. Today might value less than 2000 ( hurts so bad). This is another reason I want to squeeze as much as possible from what I have.......
what exactly is RAID MODE. i mean i have seen it in my BIOS and all. can u guys check my HDD and see if it supports a RAID SETUP. i heard you can get better ratings with RAID. right now it is just hooked up via sata cable. Newegg.com - Seagate Barracuda 7200.10 ST3320620AS (Perpendicular Recording Technology) 320GB 7200 RPM 16MB Cache SATA 3.0Gb/s Hard Drive - OEM
I installed Vista recently doing a fresh install. When i did it, it only had 1 drive visible when i have 2 of the same drives. In my bios i do not have the drives turned on to RAID i just have them in their naitive modes. I installed Vista and now it set up a RAID 1 all by itself. Has my C Drive as MIRROR[0][2] SCSI Disk Device. Now i want to stop this so i can use the other drive. Can i do this with out a reinstall? Or what would happen if i whipped on drive then plugged it back in , would this clear the other as well?
Made image of disk using Macrium Reflect Restart and setup Raid in Bios, then using ctrl-i, use Intel Matrix Storage RAID to make Raid0. Then using Reflect I restore the image. But when I then reboot I get a very fast BSOD and Vista won't boot. In safe mode it seems to lock when loading crcdisk.sys. After doing alot of research it seems that I may need Raid drivers. So question is how can I instal the Raid drivers without losing all my data? I don't want to reinstall windows.
Managed to kill my raid 0, 1 terabyte games drive today. Absolutely shattered. Maybe ten hours worth of installs on that drive. To say that I am upset is an understatement. You live and learn. Will be purchasing an extra backup drive exclusively for backing up this drive. Never will I feel this pain again
I recently purchased a HP Pavilion M8430F - It came with a single 750 Gig drive and has Vista x64 installed, - I added a second 320 Gig Drive that had data only on it - Recently i have saved all that data to the Vista drive now i would like to install XP Pro on the smaller drive and dual boot them both - OK Vista runs fine XP install Crashes - my onboard Sata Controler is set to Raid that is the only way vista will boot - if i switch it to IDE i can install and run XP but like i said vista will not boot-up switch it back to raid and Vista will boot XP will give a blue screen - The pc came with a single drive and the default setting in the bios is RAID
Noob person needs help setting up RAID 1. I have the following hardware and I would like some help in turning this into a RAID 1 storage vault. Two (2) Western Digital Caviar Green 1TB 32MB HD (WD10EADS) Vantec NexStar MX (NST-400MX-SR),Switching Jumper 1&2 are ON,Switching Jumper 3&4 are OFF, At the moment, both drives are up and running.
I posted in another thread with a similar topic. In that thread i got my SATA drives setup in a RAID 0 configuration. Now i would like to setup my 3 IDE drives the same way. I am using a VIA software RAID utility for my SATA's. I have no idea where to start. I searched the internet and it seems most of this is only done with Linux boxes. Can anyone point me to a tutorial on how to setup an IDE RAID 0, Right now in my BIOS i have the SATA ports set to RAID and not IDE, will this make a difference? I have 2 drives on one IDE bus and 1 plus my dvd drive on another IDE bus. Both buses connect to my motherboard. How can i get my IDE drives to show up in my VIA RAID utility?
