Freeview: Doesnt Detect Any Tv-signal
Dec 11, 2008
im trying to run media center through a freeview box i used to use on my tv. the aerial cable runs form my antenna into my freeview box then from the output slot into the back of my computers tv card. However in set-up when i clcik yes to do i use a set-top box it doesnt detect any tv-signal? then if i just clcik next it says no IR input found. is this talking about the IR reciever that cam ewith my tv card? or the one on the freeview box?
View 4 Replies
ADVERTISEMENT
Apr 23, 2009
Vista has detected my wireless router and I have the internet. However, wenever i plug a cable in (for faster speeds) it doesnt work It doesnt detect the cable i plug in
View 5 Replies
View Related
Apr 4, 2009
Im using Vista in my C Drive ( HDD1 Partition 1 & active partition) and I installed this XP x64 on (HDD2 Partition 2) F Drive. it doesnt detect my Vista x86 Ultimate, so no dual boot.
View 4 Replies
View Related
Feb 26, 2009
When I shut down my computer I accidently must have selected lock or logout, now when I turn on computer there is no signal to monitor. This happened once before but don't remember what I pressed to get it back.
View 3 Replies
View Related
May 15, 2010
my grandmas pc can't seem to solve. I'm getting a no signal message on the monitor when I power on the system. I've tried a different video cable, monitor, and even a new motherboard but I still get the same issue no matter what. The system is a HP Pavilion a6110n. Tried posting on their site but all they want you to do is take it in to have it serviced.
View 4 Replies
View Related
Nov 10, 2009
While playing any game, my monitor blinks off with a No Signal message and a few seconds later my computer finishes crashing and I have to reboot. I've replaced the graphics card, ram, and motherboard, and ensured all drivers are up to date, but I'm still getting the exact same issue. It only happens when playing games I can leave it running the desktop for as long as I want.
View 4 Replies
View Related
Mar 23, 2008
I have a Viewsonic LCD monitor. i just put a new pc together with an XFXForce 8600GT video card. The problem is when i boot the pc i see the bios screen fine. it's not until i see 'Micrsoft Corporation' and am about to see the status bar going back and forth that the screen goes blank and i then see 'No sginal'. I'm connected using a DVI-I cable. If i unplug the cable from either the card or monitor and plug it back in i then get video. I sent the monitor to Viewsonic which they said they fixed a problem. hmmm anyway i'm still seeing this proble. If i use a VGA cable with a DVI adapter i won't have this problem. While the LCD monitor was away i used an old CRT monitor with a VGA cable and had no problem.
View 9 Replies
View Related
Feb 21, 2009
I have an HP Media pc with dual ViXS PureTV-U48B0 tuner, and I have it configured in Media Center for ATSC only. All of the local on-air digital stations are received well, except the local PBS. The Media Center does not detect any signal for that PBS station no matter how I position my digital antenna. If I connect a tv directly to the same antenna feed, the tv detects a strong signal for the PBS station and receives broadcasts fine. I have the most up-to-date driver for the tuner card in the pc.
I saw a note on HP's site that Media Center may not work with some more recent DT compression formats. When I downloaded MediaPortal and installed it on the same PC, it detected the PBS station perfectly, but one of the other local DT stations that Media Center played well was not detected at all, plus Media Portal is not as user friendly.
View 5 Replies
View Related
Nov 29, 2008
trying to set up my tv signal in vista 32 bit media center. windows recognizes the tuner card, but doesn't detect a signal. it's a sapphire theatrix tuner (hybrid analog/digital with ati 650 pro chip). i also have a 2600xt video card installed. have installed 8.11 drivers for both devices. checked signal by pluging cable into tv, and works fine. service provider is comcast limited basic in philadelphia. no cable box.
View 6 Replies
View Related
May 15, 2009
When trying to run a Windows Photo Gallery slide show, the screen goes black and the TV reports "no signal". Some web blogs suggest it can be solved by changing the "ICC ofile".
View 4 Replies
View Related
Sep 5, 2009
Got a new laptop (VISTA) and already have a wireless router (netgear) in the house. We connected the laptop wirelessly with no problems yesterday and this morning. Then, out of the blue, I get a "limited connectivity" message even though the signal strength is excellent. Our wireless network is the only one that's listed "connect automatically" and we were connected to it yesterday and this morning with no problems.
View 7 Replies
View Related
Jun 19, 2009
I'm having trouble getting my USB EasyCap Video Capture to work on my HP laptop running Vista Home Premium X 32 bit. The Ulead software appears to be installed ok. I wonder, if the driver on the Ulead disk any good? I read that maybe an Stk1160 driver should replace the old driver.(?) When I try to use this through the TV, I get the message "no signal found". The Ulead disk is dated 2006. Is there an update to this disk?
View 4 Replies
View Related
Mar 26, 2008
Sorry, I did a search and got so much info. How do I tell if SP1 was installed on a Vista machine?
View 9 Replies
View Related
Mar 23, 2008
I did a search and got so much info. How do I tell if SP1 was installed on a Vista machine?
View 8 Replies
View Related
Feb 6, 2010
have looked through other helpful posts on here regarding the Autorun problems, having looked into that i checked all registry entries etc that were fine, however, i dont have the NoDriveTypeAutoRun where it should be all i have is
(Default)
BindDirectlyToPropertySetStorage
This doesnt seem to tie in with the write ups i have looked at and cant find the NoDriveTypeAutoRun. Also, there is no action when i insert the cdrom or dvd etc into the pc, have looked to find the manual start procedure but cant see anything in there, what drive should i be looking in?
View 9 Replies
View Related
Sep 15, 2009
GPU: XFX GeForce 9500
Gateway LX-6200
Computer Specs:
Windows Vista Home Premium x64
AMD Phenom 9500 Quad Core
8GB Ram
Serial ATA 500GB HD
ATI Radeon HD 3200
500W PSU
(any other info needed, just request)
P.S. Not sure of the MoBo build. It was the original MoBo that came with the computer.
I originally did what I normally do when installing any graphics card; I uninstalled the on-board graphics card drivers and disabled it, then attempted to install the drivers for the new card. While running the installation, an error appeared telling me that it didn't detect any Nvidia compatible hardware in my setup. So I checked my device manager and sure enough, there was only the onboard card showing up in the list. So I tried restarting the computer to see if a reboot would cause it to appear. Nothing happened, so I ran CCleaner and Driver Sweeper to clear any registry and drivers issues that could be occuring. I rebooted, and still nothing appeared. So I went into the BIOS and tried to change some settings in there. I disabled the on-board through the options there, but that only caused the BIOS to give me issues and I couldn't even reach the splash screen, so I reset it and then tried changing the load settings from IGFX-GFXO-GPP-PCI to GFXO-GPP-IGFX-PCI, saved and then rebooted. I got past the splash screen on the new video card but the computer locked up before it would load the OS. So I know that both the card and the PCI-E slot on the MoBo are working fine. But I have run out of ideas as to what to try next to get this to work.
View 9 Replies
View Related
Jun 6, 2009
Now i've installed Vista Home Premium 32-bit onto the system, but it will not detect the graphics card at all. Although i have got a display (Motherboard does not have on-board). I've tried using the driver disk supplied with the card, but it always tells me to go to the XFXForce website, so i do and download their drivers and install but CCC does not appear to get installed. I've tried the card in another Vista 32-bit System and it gets found and drivers install nicely and the card works fine. Is there anything wrong that i'm doing??
View 9 Replies
View Related
Jul 29, 2009
I recently purchased a Dell with Vista 64 bit. I have been watching DVD's the past few days on it without any problems. I was able to watch one this morning but when a put another one in I received the following message: *Unable to detect DVD or DVD device on this computer*. This computer has yet to be hooked up online, so nothing new has been added or updated on it. I rebooted, as well as un/reinstalled the driver in Device Manager
View 5 Replies
View Related
Mar 23, 2008
Using Vista, when i try to install it, it cant detect the hard drive. I proceed to scan for it and inserted my motherboard drive and it still cant find it. I go into bios and i find that SATA 1-4 shows no hard drive but it is clearly connected :/ The IDE Optical Drive works fine though.
View 8 Replies
View Related
Jan 19, 2010
We have recently installed another computer in the house. I can detect it in 'Network'. If I click on the this new computer icon and login, what features and facilities will be available to me when working on the original computer.
View 5 Replies
View Related
Sep 23, 2008
My computer was running fine this morning but when I turned it off for an hour and back on there was no display. I have a PCI-e Geforce 8600GT but when I plug the monitor into the onboard graphics it works fine. I have checked the bios and the primary device is set to PCI-e but my computer won't detect the 8600GT at all now.
View 5 Replies
View Related
Jul 23, 2009
I recently purchased a computer on e-bay. I did not know it was a server. I has a aid configuration. I bought Vista Basic. When I try to load it it says it does not detect any hard drives. Is there a way around this? Can Vista basic be loaded on this system?
View 7 Replies
View Related
Oct 17, 2009
I was wondering if this was possible with the XP drivers as when i tried to install windows 7 it couldnt detect the drivers at all. I reinstalled XP since and used online software to find the drivers (realteck and VIA/S3) as the company that made the pc (Iqon) have gone into liquidation and the drivers are no longer available from their site.
View 4 Replies
View Related
Jun 24, 2008
I am running Vista Home Premium. I had been running 2 Western Digital 500GB drives in RAID 0 mode. The external enclosure was a Fantom enclosure. The controller was going bad, so I bought a Xtrastor 3.5 x2 HDD enclosure which supports RAID 1. Anyhow, when I hook it up via USB, it only detects an 8GB drive. Once I got it to detect it as a 75GB drive. If I hook it up as an eSATA, Vista does not see it at all......It should detect close to 500GB since the other 500GB is for the RAID I have a PB5 motherboard. I have tried a lot of things via the cables and re-booting and such, no luck.
View 4 Replies
View Related
Mar 23, 2008
I've tried everything I can think of; disabling IPv6, LLTD, installing the LLTD patch on xp, turning off all firewalls, file sharing, etc.. Nothing seems to work. I'll start a listen game server on the vista computer because it's mine and it's much more powerful than the XP computer. When I try to find a server on the LAN browser, nothing come up. If I host from the XP machine, the Vista one can see and connect to the XP's server. However, this method costs frames and gameplay, so hosting a game on the Vista computer is the more viable idea. This happens in every game.
View 4 Replies
View Related
Jan 7, 2010
i had just installed crysis and played a while. ( i know it's offtopic but just for the record cos it could help to solve it) and when i tried to open IE 7 x32 it didn't detect an internet connection, after thaty tried FF, opera, anything.
No internet connection
I checked 100 times and diagnosed my network connection and i found nothing, it was fine.
Then i tried to open gtalk..... nothing
Tried google earth............... nothing
Tried windows live messenger.......guess what......NOTHING!!
(all x32 applications)
So i opened IE x64 and YAY!! it worked and here i am XD.
NO INTERNET x32 BIT APPLICATION CAN CONNECT TO THE INTERNET
BTW, All of em close with error message. Didn't happen before.
View 0 Replies
View Related
Mar 22, 2009
I've recently bought a new rig and decided to go with Vista Enteprise 64-bit version on it. I currently have a 30" Dell monitor and a 19" Packard Bell Maestro 190W setup that I used on my previous XP rig. Now, when I try to use my PB Maestro 190" Screen on the Vista machine, I get no signal. I can detect the monitor through the ATI Catalyst program but it cant it to work. The monitor works and shows stuff when I reload the computer, but it goes "No signal" just when Vista Loads...
I have downloaded Powerstrip and another monitor program to try and force it to 1440x900 settings, but still no signal.. Even wrote my own drivers for the screen with a fixed resolution 640x) but no luck. I plugged in my LCD TV instead and it worked like a charm! So i quickly switched the cables between the second 19" monitor and the TV and bam! I got the second monitor up and running! But I had to reload the computer and I lost the output, tried several times again to repeat the procedure with plugging in the TV and then the monitor.. no luck...
View 7 Replies
View Related
Oct 1, 2009
i have an HP Pavilion Slimline Vista 64, a few days ago i tried putting in my SD card in the built-in slot but my computer wouldnt detect, i tried viewing the files on my phone and the files wouldnt come up there either, it said that i had a card in but the card had 0% space used up, but also had 0% free. so i figured the card was no good anymore...then i tried viewing files from a PRO Duo stick, which the computer also has a built-in slot for, and itwouldnt detect it either(even though the little green light that indicates a card being put in flashes) but when i insert the PRO Duo in my PSP i can view the files just fine.
View 8 Replies
View Related
Jun 23, 2008
My headset and mic jack is plugged in the front panel but he panel however does detect the jacks.
View 5 Replies
View Related
May 7, 2009
My msn messenger or windows life messenger cannot detect my front mic in a voice call i.e. the caller cannot hear my voice although i can hear his. In my windows Sound Recording properties, the status of front mic button is Working. Besides, i also can record sound using Sound Recorder with my front mic. Anything to do with the setting in MSN/Live messenger?
View 6 Replies
View Related
Jan 29, 2010
I have a Dell Inspiron E1705 with Vista Home Premium 32bit. My computer has been shutting down without my doing anything. When I try to reboot, it says that it cannot detect my hard drive and my computer will not start up again.
View 6 Replies
View Related
