I did an upgrade install of Windows 7 64 bit over ultimate 64. Driver is recognized as WDDM 1.1 in device Manager. Performance scan shows as it is properly installed. However not able to get areo or advanced display options. I can not install? correct driver. I have a performance rating of 5.9 because of hard drives video is higher. Help it is an agp card. What am I missing.
View 1 Replieshave been having a problem since the time i switched over to win 7 64 bit from XP 32 bit..Got the win 7 7264 (64 bit) setup on my comp. tried installing the latest driver downloaded from Nvidia , 190.38 for my GTX 260 (Palit), but for some reason the installation doesnt proceed. have been facing the same problem with Vista and XP (both 64 bit) now..
the installation progress bar reaches around 30% and d monitor restarts and then the bar is still at d same position it earlier was and doesn move. have tried a few other drivers like 182.50 but for some reason none of these drivers gets installed..
the only breakthrough i had was when i installed it in win XP 64 bit when it started popping up the driver signature error..i believe the same issue is happening in Win 7 and Vista too but not sure.
So I've been trying to install a new graphics card update called "Nvidia update components 1.8.15" which I'm not sure if i really need it but I've been having a lot of problems with games like Call Of Duty: Black Ops lagging and I'm thinking I need this update but when I go to update my card it says it Failed here's a picture and my specs...
Operating system is windows 7 (64-bit)
Graphics Card is GEFORCE GT 540M
Processor Intel i7 2.00 (turbo boost up to 2.9 quad core)
Ram 8 GB
recently installed windows 7 ultimate x32.when i install graphic card drivers i get "display kernel driver stopped responding and has been succesfully recovered" and i get TDR errors.i can play games with default driver that windows installed but games are laggy and crashes after 30 minutes if i play on higher graphic,i can only play on low graphics and i cant play minecraft cause it requires graphic card drivers .i have nvidia geforce 9600 gt and i can usually play games at medium to high graphic and older games at high but now without drivers i can only play on low graphic,and when i install drivers i get errors .only driver that worked for me is 306 beta but when i install that driver i get TDR error
View 2 Replies View RelatedWorking with a MSI r5770 and an NVIDIA Geforce 9600 GSO. The unrelated drivers are (NVIDIA Geforce 7100/NVIDIA nForce 630i)I changed my video card and when I booted the machine to install the drivers, Windows automatically started doing just that. Problem is they are the wrong drivers. I tried downloading and installing the correct ones, but only two things happen:
1. If I uninstall the incorrect drivers through Device Manager and then try to run the .exe that would automatically install the drivers, the installation completes but nothing apparent happens. I "Scan for hardware changes" or just reboot as per instruction, and the wrong/unrelated drivers are just installed again.
2. If I try to update the driver through device manager by manually selecting a directory which contains the driver, it will tell me that the faulty unrelated driver is the best and most up-to-date driver.
For the record, the sequence of events:
1. Replace MSI R5770 with old NVIDIA GeForce 9600GSO after noticeable performance drop in former.
2. Windows 7 automatically updates with wrong drivers(NVIDIA Geforce 7100/NVIDIA nForce 630i) for the card. Can not get any signal from card.
3. Switch back MSI R5770, it automatically installs the exact same driver(NVIDIA Geforce 7100/NVIDIA nForce 630i)
I have a HT Omega Claro sound card that I've been having problems with. One issue that I have is after I uninstall the driver and try to reinstall it. It takes several attempts to install successfully.
Does this mean that the sound card is fualty? I'm not sure exactly how a driver works but i'm thinking it would try to comunicate with the hardware it's intended for and if there is a problem with the hardware that might cause the driver to have a dificult time installing.
I have a "SanDisk Ultra CompactFlash" 4GB card and an internal card reader (HP desktop). When I insert the card into the reader, the green light above the slot turns on as if it recognizes the device, but it doesn't show up. Device Manager says that the driver is installed and working properly, and I have uninstalled it,reinstalled it, and restarted my computer. A system restore isn't really an option because it isn't my computer.
View 3 Replies View RelatedI have tried posting over at the eee forums but i have not had much luck so far so i thought i would try here.
I have searched on this forum and see some discussion about this. I have a reasonable amount of basic computing knowledge but to be honest most of the more technical stuff i am seeing discussed is probably beyond me.
I was hoping i could post here in the hopes that someone could explain the steps available to me as clearly and simply as possible.
I just completed a fresh install of Windows 7 Ultimate 32 Bit (x86) after formatting my computer, which was previously running Windows XP Professional SP3. Everything during the install went smoothly, but now I'm trying to install my graphics card drivers and it's not working. Before I go further, here are my system 'specs':OS: Windows 7 Ultimate 32 Bit Mobo: ASUS M2A-VM (Green) Graphics Card: nVidia 9800 GT CPU: AMD Athlon 5400+ The first driver I attempted to install was my motherboard driver. I used the CD that came with the mobo, but the drivers were not compatible with Windows 7 so I had to run the driver under compatibility mode for Windows Vista in order to open the setup, then I installed those drivers. I then restarted and attempted to install my graphics card drivers off the CD that came with my 9800 GT. The first set of drivers that it installed were the PhysX drivers and those installed just fine. It then attempted to install the actually graphics card drivers, but then it said "The NVIDIA Setup program could not locate any drivers that are compatible with your current hardware. Setup will now exit." I opened up dxdiag and checked under the display tab and it's not showing any hardware under that tab, as if I have no graphics card. I then tried installing the Windows 7 32 Bit drivers that I downloaded from the nVidia site for the 9800 GT but when it does the system compatibility check, and error occurs that says "NVIDIA Installer cannot continue, the graphics driver could not find compatible graphics hardware." I then checked in the device manager under the 'Sound, video, and game controllers' section and only Realtek High Definition Audio is there. I have also installed the drivers for my motherboard found on the ASUS website after selecting the Windows 7 OS. I downloaded and installed the driver under the 'Chipset' section titled 'AMD Chipset Driver V1.3.0.49 for Windows 7 32bit/64bit--(WHQL).'Basically, my computer is not even detecting that I have a graphics card yet my monitor is plugged into the DVI port on my graphics card, and my graphics card is on. Does anyone know what's going on? Better yet, does anyone know where I could find drivers that will work and make my system functional?EDIT: If anyone requires any further information in order to help me with my problem, just let me know and I will get it asap.EDIT2: I just looked in my device manager and I noticed that under the 'system devices' section there is a device with a exclamation point in a yellow triangle called 'PCI Standard PCI-to-PCI bridge'. There is another one with the same name that doesn't have the symbol. Could this perhaps be part of the problem? The error for this device is 'This device cannot find enough free resources that it can use. (Code 12) If you want to use this device, you will need to disable one of the other devices on this system.' I have a feeling this is the problem. I went into my bios and enabled the "Plug and Play OS" but when I did that it made my computer run INSANELY loud. So I turned it off.
View 3 Replies View RelatedCpu restarts in every 3 secs after installing new video card from asus. i have now intel video and its b...s..t with 128 mb memory on xp. interesting part is that shows 256 in 7. but still for playing games i need better card and my friend got me his old asus card with ati GPU: EAX1300HM512/TD/128M more info: The ASUS EAX1300HM512 is equipped with ASUS exclusive innovations and ATI Radeon X1300LE GPU. and for you about my cpu:
HP Compaq dc 7600
Intel Pentium 4 CPU 2.8 GHz
2048 MB Ram
Intel(R) 82945G Express Chipset Family video now
PCI-E slot for graphix
Okay so i have an older Wireless PCI Card from like 5 years ago, I didnt have an antenna for it so i didnt use it, I recently came across the antenna and put the card in my PC, The "Ethernet Controller" says it doesnt have the drivers, and windows wont find it on its own. So i have gone to the website and downloaded the driver and software, it all tells me there are several missing .dll files.
So i downloaded them virus scanned them etc. and still no progress on getting the card installed. I dont know where the CD for it is and i doubt the CD would even work for windows 7. Can anyone help me out with this prob? Its a Wireless-B PCI Adapter 2.4GHz Model No. BB720C808230
i have prolem with installing my soundcard (supreme fx2) i have inserted it into the port on my motheboard but it doesnt show me anything on my pc i cant even find the driver for it help me plss and im not sure if i need some cabels to attach it on my motherboard i have just attached it into my pci1x slot
specifications
dell xps studio 435mt
8gb ddr3
i7 920
gts 240
my pc not shutdown after installing 4.1 sound card
View 2 Replies View RelatedI've tried drivers, updates, manual driver install, I've tried canyon support, literally everything. But I just can't get the wireless card (CNP-WF511) to work with my PC. My OS is Win 7 x86.
View 8 Replies View RelatedOn windows 7 ultimate x64
I have a Usb wireless card.... I dont have the make and model on me at the moment but when I plug this into a USB socket, Windows 7 picks it up as a bluetooth device (with errors)
I have the drivers on CD but not sure how to install the drivers, as going into device manager thinks its looking for bluetooth drivers.
Any ideas?
I bought a evga 550ti card and put it in my computer but when I turn it on it gets to the starting windows screen and then shuts off
View 9 Replies View RelatedLast Friday i installed a new graphic card, Asus EAH4870. Since the system is eratic and one ine a while, very slow
- What can I use to test some parameters?
- Could it be cause by a temperature increase?
- Power supply
_ did test inside temp and voltage with Asus software
I got a guinine version, all upgrade are done on a regular basis Browser: Chrome Win 7 64 pro 6 gb memory Drives has been tested, defragmented
I use
- Iolo System Mechanic
- CCleaner
- Kasperskyt 2011
For an unknown reason, I don't have any restore point
I have a HP built box that I purchased less than a year ago. The hard drive died, along with the motherboard.I purchased a new hard drive and the full version of Windows 7 Home Premium 64bit and had the shop replace the MB, Install the new hard drive and O/S.The motherboard is an ASUS M4A785-M, with an on-board Realtek PCIe GBE Family Controller (according to Windows Device Manager).I have a couple of additional cards installed, one is an eSata controller for an external hard drive and the other is a SIIG DP FireWire 800 3-Port PCIe card.I initially installed the SIIG because the FireWire chip set is Texas Instruments, because I have a PreSonus Firestudio Mobile (sound card, recording hardware)and it only plays nicely with Texas Instruments. The SIIG card shows up in Device Manager under IEEE 1394 Bus host controllers as "Texas Instruments 1394 OHCI Compliant Host Controller", which I "assume" is correct?
My problem is the PreSonus hardware refuses show up in Device Manager or initialize (there is an indicator light on the front of the unit that will glow blue when it is connected or flash blue-red when it isn't). PreSonus has a driver set for the Firestudio Mobile, that is called Universal Control.I have attempted to install Universal Control several times, but each attempt has resulted in failure, with the Driver version showing 0.0.0 etc. I realize this is the problem, but I have no idea how to force the issue.If I could get the PreSonus drivers to install, I would be home free (I think).he PreSonus hardware should show up in Device Manager under Sound, video and game controllers, but it doesn't.I have also posted about the issue on the PreSonus forum, but haven't had any solutions posted.This computer and the hardware are what I use to run my Recording Studio and without the Firestudio, I am effectively out of business.I should also note, that I haven't even installed any other software beyond windows 7, other than a couple of utilities. Not even my DAW or the drivers for my peripheral midi devices.
I recently upgraded my video card from a 4890 to a 6970. I loaded all the drivers and stuff. Now Aero is off and won't turn back on. When I run the Aero troubleshooter, it results in a "A problem is preventing the troubleshooter from starting" message. The Windows Experience Index is also not working. When I try to run or refresh it, I get a message "Could not measure video playback performance". I tried searching the web, but had no luck.
View 5 Replies View RelatedI installed a new graphics card (MSI N670 PE 2GD5/OC) and since then my computer has been very unstable and is crashing a lot. The card is factory overclocked and I think it is faulty. Do you know of a way to underclock the card, so I can test if it is the overclock?
PSU: Enermax EMG700AWT
*edit*So I used Afterburner to set my core clock to -104 and my power limit to 72% and this causes my card to boost to about 980MHz. With these settings the crashing has stopped. So the card cannot be used with the factory OC settings. So should I RMA?
I recently purchased a netbook on ebay with Linux Mint pre-installed. I want to rid of Linux and install Windows 7 Ultimate, however the only device I have to date is a 2GB SD card as I've either lost or broken my USB's or external HDD's.. Is there a way to create a bootable SD card with a small downloadable copy of Windows and install it to the HDD? Then download a 'full' copy of Windows to install that and activate it with a key?
Otherwise I'm going to have to go out and get a USB stick. Or is there an easier way with mounting etc?
I just bought an xps 8300 with a realtek sound card installed. But the spseaker system I have is Audigy Sound Blaster 2ZS. I'm trying to install my speakers, but I keep getting an error message that says my device is not found, and it's all hooked up properly. Do I need to uninstall the realtek program and then install my audigy speakers, or is that even possible.
View 6 Replies View RelatedThese are my system specs:
PSU: Arctic Cooling 550
MOBO: Asus M5A78L
VGA: Club 3D Radeon HD 6870
Fans: 2 x 120mm
CPU: Amd Phenom II X4 955BE + stock heatsink
Wifi: TP-LINK TL-WN781ND
RAM: 2x2gb DDR3 Corsair Value (DDR1333)
HDD: Samsung Spinpoint F3 1TB
Optical drive: Samsung SH-S222AB 22x DVD/CD SATA
Randomly (for example: while surfing the internet), on Windows 7, the computer crashes with a screen with blue and grey vertical stripes (or sometimes totally grey or black). Sometimes this screen "hides" a BSoD, sometimes it doesn't. The system crashes only if video drivers are installed. On Ubuntu 11.04 (64-bit) and Windows XP (32bit), even after installing the drivers, there are no crashes. From BlueScreenView, all crashes look identical.
I tried:
- 2 passes of Memtest86+: 0 issues
- Installing Windows 7 and then ONLY the video drivers: CRASH
- Installing XP 32-bit SP2 and the drivers: does not crash
- Using Ubuntu 11.04 64-bit: does not crash
- Uninstalling the drivers: does not crash
- Safe mode: does not crash (obviously)
I recently bought an Nvidia 7200 GS graphics card for my computer, but it is causing problems. I plugged in the card and booted up, and it somehow found a driver for it (maybe on the driver cd I had inserted). I then enjoyed 20 minutes of dual monitors, but then I had to restart the computer.
Ever since, Windows 7 will not load. It displayed the startup animation, then promptly froze. I unplugged the card, and it booted up fine, and I downloaded the latest drivers from the manufacturer's site.
However, I cannot install them, because the it could not find any hardware for the drivers! How can I install the drivers in Windows 7, if I cannot start Windows with the card installed?
I am currently using Vista that I have installed on another hard drive. However, I don't know if even this will boot up again if the card is plugged in.
I have an Echo MiaMIDI sound card for recordings, when i first installed it i had to disable my motherboards onboard sound through my bios before windows would use it. This has been fine for 2+ years.
Windows 7 (64 bit home premium) has suddenly started installing the "HD Audio Device Drivers". I dont understand this since I have all windows updates turned off. But when it installs these audio drivers it disables my Echo MiaMIDI card.
So i go to device manager and it shows the Echo card but says there is not enough resources to use it due to other drivers being used, and it lists the HD Audio Device being in use. So i uninstall it but moments after this Windows starts installing it again. It still says disabled in my bios. its driving me crazy because i cant use my sound card!
i changed the OS of my laptop from windows7 starter to windows ultimate x64. but i cant connect my laptop to the internet. some drivers are missing. {2 BASE SYSTEM DEVICE DRIVER missing, ETHERNET CONTROLLER DRIVER missing, NETWORK CONTROLLER and VIDEO CONTROLLER DRIVER is also missing.} solve this?i tried to install the ethermet driver i downloaded. but it always shows this error " error:failed to install, no device driver is present to your computer"
View 1 Replies View RelatedMy motherboard has on board audio which I disabled in my bios in order to use my recording sound card. This worked flawlessly for over 2 years. Then sometime last year Windows installed my "Missing HD Audio Driver" which disabled all sound until i enabled the on board sound in the bios again, this of course meant i couldnt use my recording card.ll Windows and driver updates have been turned off, it still installs.After many attempts at fixes i found online I gave up until more recently when i reformatted the computer and got it working. Then yesterday it started again
View 1 Replies View Relatedso my computer had a 4350 that ran perfectly fine. I just dropped in the new 4850 and now the driver isn't installing properly. Everything comes up on the display, but catalyst control center doesn't work nor does going into device manager And clicking to install the drivers. I downloaded the current CCC through the amd website and set it to simply install the video driver and it finishes with a yellow question mark and and nothing has changed. I've uninstalled and reinstalled several times to no avail, but I was just able to find the old CCC disc that came with the 4350 for version 9.6. My best guess now is to uninstall CCC and reinstall it from the disc, unless anyone has a solution to this issue.
View 1 Replies View Relatedwhen ever I install the VGA driver (any version of it- from the oldest to the newest) my laptop shows me a BSOD, each time with different messages (such as: page fault with non paged area, system service exception, memory management,...
I've even recovered it using the image disks which I've created when it was a brand new, but I still have the same problem. All the mini dump files attached.
Specs:
Sony VAIO VPCEA4BGX
OS: Windows 7 Professional X64
CPU: core I5, 2.67 GHz
RAM 4GB DDR3
VGA: ATI mobility Radeon HD 5470
HDD: 500GB Samsung
Everytime when i reboot or turn on my pc they install video controller for my integrated motherboard graphic card. I dont know why? Everything works fine, only i have is that tyni problem. And i need some help obout that
Windows 7 7260 32bit
asrock motherboard
geforce 7600gt agp
pentium 4 3.0
I've read a bunch of posts of this happening to people too but it doesn't seem like there was a permanent solution to any of them. I just installed windows 7 on a dell dimension 3000 and im using the onboard video. Everytime i reboot it wants to automatically install the "Standard VGA Display Driver" even though I uninstall it and install the Intel Display Driver that works much better and actually plays movies.
I even moved the display.inf out of the windows folder but now when i restart it still trys to install another driver over the one i have and just says that it cant find the driver for the device. And since I cant install the drivers then plug the device in, i'm kind of stuck in a rut right now. Any suggestions?