I have a computer with a P4MST890 Pentium D 3.0GHz, 9800GTX+ and a 500GB SATA. When I put Windows 7 on it the first time it worked perfect and I restarted it a few times and it loaded each time but the next morning I turned it on and it would fall into a reboot loop. If I remove the Graphics card and use the onboard card it works fine. This has really puzzled me on what could make it do that because it worked the first time with it in there.
I have been following the progress of Windows 7 through beta stages. I currently operate on Windows XP SP3 which runs great, however Ive very recently decided to go for WIndows 7 beta. I completely backed up all my information, booted from DVD, formatted and then started to install.
It copies/ expands all the files to 100%, then does a normal restart, It then comes up with starting windows> registering entries etc, the carries on finalising the install only to reboot itself?
After the reboot it gives me the windows recovery screen. If it tries to boot up it just goes into a reboot loop. I am sooo confused.
The thing is I would say I know my way around PC software and Hardware very well. I have tried different BIOS settings, Optimising defaults, Load-Fail Safe Defaults, Creating New Partitions etc.
The problem is minor and it's just a bit of an annoyance I've been dealing with from time to time.[CODE]Basically, If I were to I put my computer to sleep(using the sleep function, not hibernate) and try to wake it up within a few seconds, the computer would go into an automatic reboot loop that would continue to boot, shut down, boot, shut down until I turn off the PSU completely. I'm trying to figure out which component might be causing this problem, if any. I've updated my bios, drivers, and ran memtest but nothing seemed out of the ordinary and it didn't fix the problem.
Windows 7 Home Premium 64-bit OS, HP G61-304NR laptop is auto rebooting over and over again. I have tried system recover from my recover disks - it did not work. I ordered system recovery disks from HP and had the recover disk reformat the Windows partition (I have a valid backup of this computer).Tried to boot in the following modes:
-Safe Mode -Safe Mode w/Command Prompt -Low Res Video -Disable Driver Signing Enforcement
None of these things work. It appears that the problem may be associated with atipcie.sys driver. I assume this because the safe mode driver boot stops at disk.sys and the next driver that needs to load is atipcie.sys. At that point, the computer goes into windows and then reboots. I cannot get to a command prompt. I have tried to get to a command prompt by booting from the recover disk, by booting through safe mode with command prompt. I cannot get there. The laptop successfully gets through BIOS, and goes to Windows, but then it goes through some command screens (looks like scripts, cscript.exe), but then automatically reboots.
I'm trying to install windows 7 on my laptop through a USB key, but so far I've been unsucessful. What's been happening is that everything goes fine until the installer needs to reboot itself, then the computer reboots, but installation process begins again from the beginning. No error messages or anything like that. I've begun the installation process 3 times now, each time the installer thinks it is installing a new copy.
For reference, I have an IBM Thinkpad T43, and I'm installing Windows 7 Professional.
My computer keeps on looping, it starts loads up the gigabyte bios picture, most of the time loads till it says "starting windows" and sometimes it just loads the gigabyte screen and restarts continuously in a cycle. I ordered 2 exact same PC's and only 1 of them do it. The specs are; i7 2600k, Gigabyte 6970, 8 GB Kingston 1600 MHz and Gigabyte Z68X-UD3h-BC which was replaced after one day because of a power surge. also : 990 WATT PSU. I got this new PC it looped, returned it, they fixed it, it looped. Now sometimes this pc starts, like right now im on it. IT starts sometimes i also updated my bios recently and the guy had to change the ram from 1333 MHz to 1600 MHz because it apparently does that as default when its updated. i also had to have a keyboard replaced it just died from this PC, and had many issues with the usb ports than a driver fixed it.
I built my own custom PC through parts I ordered from newegg last week. Putting the computer together was surprisingly the easy part, while installing a windows OS has been ridiculous. I tried installing windows xp for a few days after running into 0x7b bsod errors, finally getting it to the point it would set up and then would reboot and put the monitor in sleep mode. I tried vista which just immediately gave me the "putting the monitor to sleep" thing right after it said "starting windows." Now i'm trying windows 7 and I once again can't do it. It boots up and does the setting up windows bar, then when it goes to "starting windows" it reboots itself, and does that on repeat. I really hope somebody can help, it's incredibly disheartening to spend $500+ just to have it do anything within its power to not work. I've tried unplugging everything that isn't neccesary, running 1 stick of RAM, I've tried setting it to IDE, RAID, and HCPI. I have tried 2 separate Windows 7 discs. I've reformatted the HD (using xp) multiple times and tried multiple partitions. Windows 7 simply wont even let me get into the installation portion. [code]
Yesterday I was installing XP on one of partitions I made for it,because I had problems recording stereo tracks for studio on Windows 7( in my previous encounters like that,it worked on XP ).After installation of XP it would restart and just give Unable to load operating system and I couldn't boot in Windows 7 because as most of you probably know,XP overwrites boot section of Windows 7( but that's an easy fix with EasyBCD ).Now I tried fixing the problem with Windows 7 installation DVD and startup repair but no use,then I tried MBR tutorial and it got me to splash screen,but that's where my infinite loop started.Then I tried doing backup with command prompt as in one of tutorials here: Startup Repair Infinite Loop Recovery but no results unfortunately. Or am I going to be forced to do clean install? I temporarily installed Windows 8 Release Preview on XP partition just so I can do stuff until Windows 7 is fixed.
I downloaded the student version of Windows 7. I'm running Vista business so I had to do a clean install which went fine, it went through the first two steps fine (I forget the names) and then says it needs to restart to finish.
It restarts, goes to the new windows start up screen (which looks nice), that screen goes away and then shows the cursor for about 5 seconds and then the system restarts. It'll do this for hours. I also have a DVD version of it, tried that, same story. I've tried updating drivers, unplugging everything, and hitting F8, nothing worked. Any other ideas?
I am at a loss of what to do, I have tried everything but come up empty every time.Here are my specs:
Windows 7 64bit Intel Core I7 - 2600k CPU @ 3.40ghz Gigabyte Z68XP-UD3 motherboard 8GB ram Nvidia 550TI 500W power supply
I was beta testing a new online game called Star wars the old republic, my old much slower rig ran the game fine, but I was in dire need of an upgrade. All my specs listed are new parts except the power supply. They were installed prior to the game, as well as a new install of windows 7 on a formatted hard drive.I was running the game maxed out settings with forced anti aliasing. My computer would subsequently crash into a reboot loop upon entering the game world. The computer it would turn on, you would see the F12 for boot menu etc then crash restart in an infinite loop.Updated the bios for my new motherboard I thought my power supply was the issue so I unplugged all the fans except one + the CPU fan. Computer still crashed upon launching the game.I burned the .iso of my OS onto a dvdr, so I put it in hoping to repair some files + finished updating, the game finally launched.Turn to today, the the beta was over, so I install bad company 2. Thinking the power issue wasn't the problem I plugged all my fans back in, and cranked the settings up, load into the game. I crash within 20 seconds of a multiplayer game.Research shows my particular motherboard is prone to the reboot loop (Great) it however works just fine when normal shutdown/start up occurs. Some have told me my OS is corrupt, or it's a ram frequency issue. I am not too tech saavy when it comes to computer, but I dont know what else to do. I spent a good chunk of change trying to upgrade my system and I can't play any games/intensive programs except BROWSE the internet Just went into advanced BIOS and turned off the motherboard gpu, at it was set to be on, it is now set to be on when no card is present. Game now crashes, but 1 minute later than normal?
My original os is windows 7. So today I connected a hard drive from a windows xp machine so I could transfer some files. When I powered the computer back on I got a blue screen right after the windows 7 loading screen and the computer rebooted. I then got the black screen asking if I want safe mode last known configuration or start windows normally. I chose start normally and i got bluescreen/rebooted back to this screen. I then chose last known good configuration and was bluescreen/rebooted back to the screen, this time I chose safe mode. Safe mode began to load files and then stopped at mup.sys bluescreened and rebooted. The system then tried to do the windows repair thing and I did the system restore option and rebooted, this didnt help and I put in my windows 7 installation cd hit repair and tried bootrec.exe, none of the options worked [fixmbr fixboot etc] and the system doesnt recognize that any OS are installed.
I reformatted my hard drive to install a copy of Windows 7 Ultimate, 64bit (I had Windows 7 Premium, 64bit before) and the installation ran just fine. After the installation, it boots up to what I guess is the desktop, waits a few moments, then just reboots. Every time before it boots it goes to the "Windows is loading files..." screen. I also tried 32bit, but got the same results. If you need more information, just ask and I'll be glad to provide it for you. A USB stick was used to install.
when I was playing a game and it crashed on a loading screen, I then could only boot into windows extremely slowly so I knew something was wrong. Since then I have booted into safe mode and done a virus check and it found nothing, I had then done a start up repair multiple times and for one reason or another the system would then reboot just as the login screen is loading. I have recently de fragmented the drive externally and run a slow disk check which found nothing. I've launched start up repair again which says it's unable to fix the problem and I can't boot into safe mode because it'll reboot. I should also mention I was having problems with the drive a few weeks ago where I was getting different error messages before booting but I managed to sort that out. If a solution can't be found it would be safe to say the drive is failing. Here is the bsod when I disabled automatic rebooting along with the startup repair error.
Had 1x 2GB Kingston 667MHz stick, and decided to buy another one. I should point out that both are fully working and were bought brand new from Amazon. I was forced to reinstall windows (Windows 7 Professional 64-bit) for other reasons, and the installer would get to "Starting Windows" then would restart. Did this as many times as I booted it up. After messing around I took out one stick (took out the old one and just had the new one in) and the installer worked perfectly. Got into windows and shut it down to reinstall the other ram stick. When I booted it up, it did the same reboot loop. Seems like it just doesn't want to take 4GB. BIOS says: Installed Memory: 4.0 GB, Memory Channel Mode: Dual Interleaved. Why won't my XPS 600 boot with 4GB RAM!? It IS a 64-bit OS (had to double check just to make sure)
I'm building a computer myself and I can't for the life of me get windows 7 to install. Here is my configuration and what I've tried..
Motherboard: GIGABYTE GA-X58A-UD3R LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard Rev 2.0, BIOS version �FA� Processor: Intel Core i7 930 2.80GHz 8MB LGA 1366 L3 Quad Core Desktop Processor - BX80601930 Memory: Corsair XMS3 6GB DDR3 SDRAM Memory Module - 6GB (3 x 2GB) - 1600MHz DDR3-1600/PC3-12800 - DDR3 SDRAM 9-9-9-24 version 2.3a Optical Drive: ASUS Black 24X DVD+R 8X DVD+RW 12X DVD+R DL 24X DVD-R 6X DVD-RW 12X DVD-RAM 16X DVD-ROM 48X CD-R 32X CD-RW 48X CD-ROM 2MB Cache SATA 24X DVD Burner - Bulk - OEM Power Supply: OCZ Technology GameXStream 850W ATX12V & EPS12V Power Supply ard Drive: Western Digital Caviar Blue WD5000AAKS 500 GB - Hard Drive � Bulk Graphics Card: GALAXY 70XKH3HS8GUX GeForce GTX 470 Graphics Card - PCI Express 2.0 x16 - 1.25 GB GDDR5 SDRAM Operating System: Microsoft Windows 7 Home Premium 64-bit 1-Pack for System Builders � OEM Case: Cooler Master HAF 922 RC-922M-KKN1-GP Chassis - Mid-tower - 10 Bays � Black
What I first did to install: I change the bios to boot from the Optical Drive Put the Windows 7 CD into the optical drive.Follow the on screen instructions for the windows install. Windows copies the files, extracts and installs. The system reboots. When Windows attempts to start for the first time the windows logo comes up and does its animation. The system then reboots. The screen comes up that tells me windows didn�t start properly and do I want to try safe mode, etc etc. If I do safe mode drivers scroll until it gets to disk.sys. At this point it freezes for a minute or two and reboots.
Things I�ve tried:
I have pared down to 1 stick of 2 GB of the ram I�ve tried using both of the other sticks of ram (individually) in case I had a bad stick I�ve tried with an older ATI PCI video card in case it was a video card compatibility issue I�ve tried reformatting and deleting the system partition and reinstalling I�ve tried reformatting from another working computer and reinstalling I�ve tried many windows repairs, often it says it can�t fix it, or tries something and restarts.
Once it was �repairing disk errors� and it did that in about a minute. Didn�t work. Othertimes it gives me a failure during setup, tries to fix it, didn�t work.I�ve reset the bios to optimized I�ve tried manually changing the multiplier of the ram in the bios. fter about 25 -30 reboots bios resets and repairs it finally looked like it was working, did some more installation stuff, restarted, and started the damn reboot sequence over and over� Now when I run in safe mode the last line to come up is Loaded: windowssystem32driversClasspnp.sys Looks like it made it a step farther, for no reason, I really didn�t change anything except repeated attempts. Many more attempts at repairs and resets haven�t gotten any further.
So I decided I wanted to try Microsoft Security Essentials for some reason. I uninstalled Avast and all traces of it. I installed MSE and everything went smoothly. I noticed it was setup to automatically scan every Sun. night. I left it that way. Monday morning I wake up to the infinite reboot. Because of the aforementioned I am 95% sure it is software related, but maybe that is because I don't want to spend money on new hardware right now.
I've tried every safe mode. I've tried to load the last known good config. I tried to repair with my Win 7 disc, but it always restarts itself before I can get anything done. I also tried system restore and also reformatting with the disc, but I get no more than a minute once I've started the computer. I've also tried scheduling memory and system checks at startup but they never get a chance to run.
My system: Win 7 i5 2.67 ghz hitachi 500gb hd 4gb dd3 gtx 560ti
My Windows 7 ultimate x64 is rebooting itself at the welcome/logon screen, in safe mode only. Normal mode is fine. The reboot happens instantly, after a few seconds at the welcome screen, the screen goes black and the system is rebooted as though I had hit the "reboot" button on the case, with no clean shutdown taking place. I am at a loss to know what could be starting in safe mode, that _doesn't_ start in normal mode, to cause this.
I have recently done a repair install of windows (the problem was there before that), I have tried replacing the safe mode parts of the registry with clean ones downloaded from an AV vendor website (mcafee if I remember correctly), and have tried doing sfc /scannow which resulted in a corrupted boot.sdi being replaced with the archived copy. None of these have fixed the problem.
Obviously, given that I have a usable normal mode, and good backups, this isn't the biggest problem ever, but it would be nice to get it fixed especially for the next time I need to fix a dodgy driver install or similar. What I can check next, particularly in regards to understanding the startup process and what will be loading at the welcome screen that might be causing the reboot.
Today windows downloaded and installed SP1 automatically. After that, the power went off, when it came back and I booted the PC it started updating as it would usually do, it finished updating then rebooted and started updating again, this happened around three times (no failure, just installs over and over again). I became tired so I shut it down and it displayed "Failure configuring Service pack. Reverting changes", after that it rebooted again but began installing the SP once more, I rebooted again in safe mode and it began reverting changes once more only to reboot again and attempt to update once more.Right now it's reverting changes once more and I'm just sitting here waiting and I don't know what to do (also, it's been reverting for quite a long time, around 30 minutes)
I have windows 7 home premium 32 bit dell laptop. Lately, it takes more than 10 minutes before it boots before the windows logo appears). From there the computer works normally. I got a suggestion to check for malwares or viruses so that is what I did. I started by going to msconfig and edited the boot options to start automatically to safe mode with networking, then rebooted my system. After booting, it loaded up the initial screen of safe mode, but then it restarted by itself.
I am now stuck on this reboot loop going into safe mode, it won't even let me go back to normal mode. I went to startup repair, but it didn't find anything, so had to reboot again onto the same situation. I have searched for possible answers, and the best that I could get was to remove the safe boot options and go back to normal mode. The syntax to type was bcdedit /deletevalue {default} safe boot but it didn't work, same with bcdedit /deletevalue safe boot.
I am getting this : "An error occurred while attempting to delete the specified data element. Element not found."
So I booted up my PC today and every single time it would get past the windows loading screen, a BSOD would flash on the screen for a split second and reboot. I tried booting into safe mode and that would not work either. The next step I figured would be to format and do a clean install, but here's the thing... Windows didn't even recognize my partition! It has my other 2 HDDs but not my Windows 7 partition. The HDD in question shows up in BIOS, but not in Windows. So, should I just get a new HDD? Startup Repair didn't work either, as it just hung/froze.
Graphics card: ATI Radeon HD4870 x2 Running on windows 7 x64 ultimate
I was browsing away and my whole pc froze, with a strange little box around my cursor, although the sound was still working, I force shut down it and restarted and little message popped up saying the display driver has stopped working, I tried multiple things to solve this, to no avail, eventually it kept happening and it got so bad the computer would not start, i tried all of the "F" keys on startup and none worked, eventually i took it to a shop who wiped everything clean and it worked again.
Around 2 months down the line low and behold the same problem happened again, I found a solution and installed a program called driver robot, I used it and installed many outdated drivers, this seemed to fix the problem. For about 6 months, now it has happened again, my computer has now shut down and goes into a constant restart loop, as it is doing this the screens that show up are littered with dots and lines of many colours, I just need workaround on this, preferably without loosing all of my files.
I have the Asus A55A EB71 (although I can't find it on Asus website itself, probably known under another name) So long story short, this is what I did that is causing my current problem:
F8 Boot, repair mode, restarted during the middle of "loading files" (yes, I know, bad idea) If I try the safe modes or repair, it says windows is loading files, then it says to repair etc etc (recommended), and start windows normally. Start windows normally sends me to Reboot and select rproper boot device.
Anyway, I get the reboot and select proper boot device screen. I checked BIOS, boot option 1 = "windows boot manager...", #2 = dvd, so not boot option priority issue I tried F9 Boot (to do this: URL], however, only option is Windows 7, and windows memory diagnostic.
The laptop did not come with a recovery disk, nor did I make one. I had a system restore file on an external hard drive, but I just formatted the drive today for a Mac thinking, "hey, I never have those problems, I'll just make a system restore when I get home."
What can I do? It's a relatively new laptop so i can factory reinstall, although I dont know how. I tried this: [URL], but there is no recover windows to entire HD option.
I recently build myself a gaming computer the specs are as follows: i5 3570k 16GB G.Skill 1600 Mhz ASRock Extreme4 Evga 750 Watt PSU Asus GTX 670 2GB
After I Installed all of the drivers for everything but the graphics card it was finally time for that and as soon as I downloaded the newest drivers from Nvidia and restarted my computer I immediately got into a reboot loop and any time I've tried going into safe mode to delete the drivers my computer restarts. On top of all of that there are these red vertical lines all over my monitor.
When I start my laptop, it shows the HP logo, begins to boot and is almost instantly interrupted by a white screen that scrolls down from the top. It reboots right after the white screen.I am able at the HP logo screen able to navigate to System Restore and that is where I run into my next problem.When the System Restore window opens for confirmation it shows that "Local Disk (C) (System)" status: "Ready to restore" and the check-box next to it is checked.The next line has a empty check-box for "Local Disk (C)" with the status: "The drive cannot be found." I can also successfully boot into Safe Mode with Networking. I can access all my files. Which leads me to believe that it is a hardware problem. Possibly the motherboard or graphics card.
i have heard a lot of my friends saying that they are unable to play high resolution and high definition games on their pc and told that they are on a low budget to buy a graphics card.here is a solution for that:there is a software named 3-d analyzer available in the internet which acts as a virtual graphics card for playing games. you can enter the graphic card needed from the 4 available graphic cards available and then you can get the attributes of that graphic card..if fine tuned,you can play games at the range of a 128mb ram virutal graphic card on your non graphic card pc. note:graphic intensive games,that requires atleast 512mb of graphics memory can't be played through 3d analyzer if you don't have a graphic card,but you can try running it if you have a 256/128 mb card. steps for using the 3-d analyzer software, *first download the file from here, *then extract that software and open the software, *then,select the exe file of the game that you want to run, *choose the select option, *then you can choose the attributes the options you require to play the game,*the attributes may be pixel shader or disable rendering in the game or emulation or some other options specified, *then,enter the device id and the vendor id for the graphics card you need from the available graphics card on the right.*i would suggest the ati radeon 9800pro to run most of the games like fifa 08/09 or prince of persia two thrones/sands of time, *then choose the run option and then i assure that the game would run for you at a decent/playable speed. note:1.if it shows any error that a file is not found pls reinstall the software.2.if the screen turns black/blank then play with the options in the s/w, by trial and error method,if fortunate,may be,you'll be able to run your favorite game.3.if pixel shader/shader version x.x not found,then select the appropriate shader model and run the game. all the best..happy gaming..if any queries post it below.how to: use 3d analyzer video at Internet
I purchased diablo 3 for my husband & my video card is not supported so he's unable to play, my computer is a HP P624 f-b desktop with a Intel GMA intregrated graphics, I am aware I need to up my power supply also, I have no idea what video card can be used to upgrade so the game is playable, not looking to spend a fortune?
I've completed a new custom build, but have had problems with BSOD from the beginning with any installation of Intel Graphics drivers or the installation of any graphics card.
When I first completed the build, the XFX-7950 Black was installed. I booted to BIOS without issue, but when I inserted the Windows 7 (64 bit) it would boot through the windows logo screen but immediately BSOD right after going to the first install screen.
I removed the graphics card, and was able to complete the full Windows install without issue. I updated Windows and the drivers on the system but as soon as I installed the Intel 3000 Graphics driver, it would BSOD on every restart. I recovered back prior to the Graphics driver install and installed all other drivers. I updated the BIOS to the latest version.
I have reattempted the XFX 7950 multiple times in different slots, but with the same results. I also attempted my Radeon HD 4550 from my old computer but it gave the same results. It always boots through the Windows logo screen, but BSOD within a few seconds of reaching the password screen.
I broke down and installed Driver Whiz, which did detect multiple outdated drivers that I had not caught, but none of these fix the issues.
I've attached the requested zip. I don't think all BSOD's are showing up, as I've had to use recovery points after installed drivers didn't work. The last .dmp on 19 JUL was a Intel Graphics driver install attempt that I pulled off in safe mode before recovering back to the pre-driver point.
System: ASUS P8Z68-V Pro/GEN 3 Intel 2600K XFX R7950 Black Edition OCZ 850W Crucial 128 GB SSD Seagate Barracuda 1 TB HD Corsair H100 Windows 7 64 bit (full)
every time i'm doing a restart to my computer i see on the network icon next to the clock a yellow triangle that indicate on a problem. when i open it i see "no network..."
in order to fix it i need to DISABLE & ENABLE my network card and after this step the connection is back & i have internet. Someone know why i have this problem & how to fix it for good?
the screen going on the fritz only when playing a video. i have not tried playing a video on vlc or wmp to test this but it seems almost every time a video pops up on a website, or if i go to Internet, my screen goes crazy.per the other thread, i swept my old drivers and re-installed the newest (which was 12.9 beta) and everything is ok, cept these videos. to fix it, i have once or twice gotten lucky and been able to hit escape and it goes back to normal. otherwise, i have to hit the power button and make it go into sleep/lock mode. i have a second monitor hooked up and it doesn't do what monitor one does, which is very odd.card is xfx radeon r7770 ultra overclocked black edition (factory overclocked)p.s. tried to use the uploader for pic and it wasn't working for me at all. tried to use imgur also, said it was down for maint.
