Network Adapter Issue
Jun 20, 2009
I loaded some software that I didn't want to 'activate online' and to insure that there wasn't any internet connection I manually disconnected the cable from the port. I plugged it back in and I'm reconnected, until, I reboot.
Once the computer has rebooted I'm no longer connected. I either have to do one of two things, one disable/enable from the device manager or two uninstall and reboot till Windows 7 finds it and re-connects.
Any time after that if I reboot I never get internet connection. If I try to load the drivers I get a compatibility error/issue and if I do a driver update from the device manager it says I have the current/latest drivers.
Edit: I'm getting the yellow exclamation, to be more specific.
View 6 Replies
ADVERTISEMENT
Feb 11, 2012
I disabled my network adapter then restarted and now the adapter is no longer showing up in my network connections. How in the world do I get it back? I have looked at other options (like under the registry which was suggested on a couple of places). I have never seen this happen before. I even reinstalled my drivers and still nothing. How do I enable it again?
View 7 Replies
View Related
Aug 23, 2009
I have a linksys usb600n (v2) using the Windows 7 driver from linksys. It installs and is displayed correctly in Device Manger - BUT it doesn't appear in the Network and Sharing Center as an adapter. This same device and driver were previously working just fine in this system - but I rebuilt the OS (clean install) after testing a number of security products out.
The initial install went fine - no problems that I remember - just plug in the adapter and install the drivers obtained from Linksys (Ver 3.00.01.0). I tried the same thing on the re-build and it looks fine until I go into the Network Center and can't set up wireless networking since the adapter does not appear.
SIW shows TWO (2) linksys USB adapters under Hardware/Network Adapters, but does not show the network adapters in the Network Information section.
Any ideas?
View 3 Replies
View Related
Nov 1, 2009
Installed Windows 7 on two home-network computers. Everything appeared to be good, including networking, but I could not access printers (linked through each computer) with the opposite computer. Windows update offered an update for the Broadcom 802.11n network adapter, but when I installed the update I completely lost the network.
I had to revert to the old driver in order to reastablish the network. But the printers still are not recognized. The network adapter on the secondary computer is a Linksys WMP300N. I did try turning the router off for ten seconds with the updated driver but that had no effect.
Anyone had this problem?
View 0 Replies
View Related
Apr 3, 2011
I just got a new computer with Windows 7. My old one was using XP and I had a Linksys USB adapter for it, but it's not working on 7, and I guess it probably shouldn't. So I'll need a new one to connect to my router wirelessly, right?
View 5 Replies
View Related
Dec 23, 2011
My VPN does not work any more and kept getting the message that "Failed to connect for following reason :activating VPN adapter failed ". This happned after my system got hit by the Trojan "Win 7 Antispyware 2012 " and malware was run to remove it .
I am on windows 7 OS .
View 5 Replies
View Related
Oct 14, 2009
im running windows 7 on my toshiba sattelite L15 S104 and and i cant find a driver for my T60N871 802.11 b/g WLAN wirless adapter. its made by intel but it says foxconn with it also. ive tried toshiba.com and intel.com and still cant find it. does anyone know where i can because i really dont want to go buy a new wirless net work adapter.
View 2 Replies
View Related
May 1, 2009
I upgraded my windows 7 beta last night to the RC1 release. The only issue i am having is that now my wireless driver is not working correctly.
under the device manager the error is "Windows cannot initialize the device driver for this hardware. (Code 37)"
I am using a macbook pro with bootcamp on it, the initial beta public release of Windows 7 picked up the drivers fine. For some reason after upgrading i can get no wireless though. I have tried downloading vista drivers, and just about everything i can think of. I also downloaded the Bootcamp Vista 32 Update from mac, but it did not resolve the problem either.
View 9 Replies
View Related
Mar 1, 2011
Running Win 7 Ultimate 64 bit. I have an HP desktop with a Realtek PCIe GBE Family Controller. All was working fine until I got the automatic Win 7 critical update issued 2/15/2011. That is the only thing I can think of that changed. Now for the problem.When my PC boots it appears that the NIC driver is not being started giving me no access to my Netgear WNDR3700 router and thus no internet connection. If I uninstall the Realtek Controller using device manager then restart the system it finds a new device, the Realtek controller, and installs it and I can then access router and the internet. When I shut it off the next time I start it up again I have no access to the router.I did restore my system back to 2/14/2011 using the restore point created by the 2/15/2011 update and it worked fine until Windows automatically installed the critical update again. That is why I blame the update. Since then there have been two or three more critical updates but the problem persists. Also I can no longer go back to the 2/14/2011 restore as it seems the system only retains the latest restore points and 2/14/2011 is gone.One other thing is there is another listing under Network Adapters in Device Manager. WAN Miniport (PPPOE) it has the little triangle with the exclamation point in it. I tried to reinstall it searching both my hard drive and the internet for a driver but it can't find one. Under Properties it also says, "Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)" However this does not stop me from accessing my router using the method described above.
View 3 Replies
View Related
Apr 13, 2011
1- 3 days ago my network adapter just disappeared with no good reason
2- Installed a new OS "32" and issue remains the same
3- Installed a new NIC with no changes
4- tried to reset the network adapters through CMD and no hope
any clue cause my last taken action should be "breaking my PC into pieces"
View 9 Replies
View Related
Feb 25, 2011
my usb network adapter cannot work in the win 7 evironmnet my laptop is dual boot.
View 1 Replies
View Related
Mar 6, 2011
i have a windows 7 laptop and i need to install a network adapter so i can get online... i got a 2nd laptop so its good but WHERE can i get the driver so i can put it on a usb and install to the other laptop?
View 6 Replies
View Related
Jun 14, 2011
I bought a new laptop and I can't connect to the internet because it says "Windows could not find a driver for your network adapter."
I can try to manually download one but I don't know what network adapter I have. When I bought the laptop the only information it gave me was that is has an HM65 Express Mobile Intel chipset based motherboard. No word about what kind of network adapter.
View 5 Replies
View Related
Jul 5, 2012
what the network adapter driver is called for my z77 extreme6. I'm using a usb drive to transfer drivers from another computer. No. I don't have my disk that came with the motherboard.
View 3 Replies
View Related
Aug 8, 2012
I've recently came on my desktop and i realized that the internet connection was off it had a red XBut it was working fine before? im not sure what happened. Anyways i cannot seem to find the driver to download it nor do i know what it is.Amd Athlon ii x2 245 processor 2.9ghz4.00 gb64 bitati radeon 4200insiprion 570dell
View 3 Replies
View Related
Nov 22, 2012
ok i have a windows 7 laptop and i need to install a network adapter so i can get online... i got a 2nd laptop so its good but WHERE can i get the driver so i can put it on a usb and instsall to the other laptop
View 1 Replies
View Related
Dec 14, 2012
I have two network adpatro in win 7 one is lan card network adpator that use ip 10.1.4.100/16 Gw 10.1.1.249 one is VPN network adpator .If it enable , the IP will ber 192.168.2.X /24 .
I want to make bridge and so , the computer from 10.1.4.XXX /16 can use my computer to reach the 19.1.68.2.x . In this case , my PC work as a router .
I try to make bridge with above two adaptor . But after enable the bridge, I still cannot ping ,telnet 192.168.2.XXX from 10.1.4.xxx PC even after setup the route table .
View 3 Replies
View Related
Aug 26, 2012
I just installed Windows 7 Ent. (64) and can not connect to the internet due to the fact te system can not find a driver for my network adapter.I ran the DEVMGMT and it shows no network adapters BUt it shows two yellow.
View 14 Replies
View Related
Jun 5, 2009
I'm having a problem with staying connected to my network with my Windows 7 PC. I have several other machines running XP and a laptop with Vista none of which are experiancing the problem.Basically what happens is the network adapter drops the connection whenever there's a high amount of throughput. Streaming media, transfering files, gaming, download all do it. Browsing is totally stable but as soon as I try to download a few things or move some stuff around the network it disconnects.It's a Linksys AG241v2 with the Pheonix Firmware and an Asus Crosshair in the PC. I've tried sifting through the forums but none of the solutions have worked so far.
View 9 Replies
View Related
Aug 29, 2011
I have a AR9285 Wireless Network Adapter installed in my Asus Eee PC. Whenever I wake up the computer from hibernate or sleep, the wireless adapter takes a full minute or more before it will actually connect to a network. Once it is awake and connected, I have no issues, and I have no problems connecting to different networks. So it is working as intended most of the time. When starting up the computer from "off," it is usually fine as well, since the amount of time it takes to fully start up the computer is usually about enough time for the adapter to get going (though not always).I cannot ever "quickly" look something up on the computer, as I have to wait a few minutes in order to be connected to the internet. Has anyone had or heard of this problem? I checked and the driver is up to date.
View 1 Replies
View Related
Sep 30, 2012
A few months later i wanted to upgrade my 32 bit to 64, since i could only use 3,16 GB ram, and my computer has 8GB. So i bought a win 7 home premium 64 bit and installed it. Now i face the same problem, my computer can not detect any wireless network adapter, though i'm 99% sure that my computer has one.
View 6 Replies
View Related
Jul 23, 2011
Can anyone tell me if I can install a Broadcom 802.11g network adapter intothe HP G5326UK Desktop PC?
View 3 Replies
View Related
May 21, 2009
since build 7068 I've been facing this problem with this network adapter, will try to explain as good as I can.
Problem as following: Everytime I start the pc after one or two minutes I lost my internet connection and when I try to restart the pc it hangs when shutting pc is showed, forcing me to shut it down only whit the power button.
I have tried to install the vista x64 driver that I have for this network adapter but cannot installed since is onlyfor vista x64, neither in compatibilty mode. After a few research managed to installed it via safe mode. and by now is working good but device manager shows a warning icon and a Cannot start device code 10.
any knows is theres a win 7 update driver?? can I just keep ignoring the code 10 till this bug is fixed??
View 6 Replies
View Related
Jun 23, 2009
is there anybody have the driver for win seven ?
View 2 Replies
View Related
Jun 2, 2011
windows did not detect a properly installed network adapter, you will need to reinstall the driver, i cannot get on to the net to reinstall the driver , ALSO TRIED THE DEVICE MANAGER,ethernet and network controller have got yellow warning sign and when you press any of them they cannot find the drivers, windows 7 ultimate 32 bit
View 5 Replies
View Related
Jan 15, 2012
I have a pluscom network adapter which I use to connect my xbox to xbl through my pc. I've recently had to clean reinstall Windows 7 so I've I need to reinstall the driver for this, but can't find it online anywhere.
View 2 Replies
View Related
Nov 24, 2012
Okay so I have no clue how to do this. This message pops up every time I try to troubleshoot my internet connection. Windows did not detect a properly installed network adapter. If you have a network adapter, you will need to re-install the driver. This is funny though because my network was working find but there was this issue with my laptop (Windows 7 Home Premium OA 32 bits) and I repaired and now the problem is gone but now I have the problem with my network. What do I do?
View 1 Replies
View Related
Nov 24, 2012
This message pops up every time I try to troubleshoot my internet connection. Windows did not detect a properly installed network adapter. If you have a network adapter, you will need to re-install the driver. This is funny though because my network was working find but there was this issue with my laptop (Windows 7 Home Premium OA 32 bits) and I repaired and now the problem is gone but now I have the problem with my network. What do I do?
View 7 Replies
View Related
Oct 13, 2009
Anyways i just got my windows 7 ultimate working and everything is working fine expect my network adapter. I installed the vista drivers found on the belkin website. Which did the trick and made it work. But i noticed every 2 hours or so the adapter would disconnect from my internet while everyone else in the house who are on xp/vista works percfectly.
Now im not sure if this is because my network adapter isn't compatilbe with windows 7 or something else. Oh and im using Belkin Wire G+ Mimo ver 3001
Can anyone help me out, and also is anyone else getting this problem If there is nothing i can do what network adapter would you guys recommend which works with windows 7 and i can get in the uk :P?
View 4 Replies
View Related
May 6, 2009
my Lenovo S10e Netbook features a Broadcom 802.11g Network Adapter Hardware ID DEV_4315 wich used to work perfectly under Windows 7 7000.
After having installed the RC it sais the driver could not be initialised. Deleting and restarting etc. did not help, Winupdate sais: driver is up to date.
Searching Broadcom's website left me even more confused..
View 0 Replies
View Related
Jan 10, 2013
Since a week, my Network (LAN) adapter on my HP Compaq 6730b Windows 7 64bit, einstalls itselves.I have no idea why this happens. Have installed the newest driver from hp.com (Broadcom Wireless LAN Driver for Microsoft Windows 7 ) but there's no change.(i've installed it, and a few minutes later it deinstalles itselves again -.-)There's only a message: "The network adapter was successfully removed."Updates from windows 7 are also done everytime there's one.I'm in the internet now with my WLAN-Adapter...but the speed is not that high if you know what i mean
View 3 Replies
View Related
