I have Windows 7 home installed on my Aspire one, I have tried to instal an IP security camera but I k keep getting "Sorry. Your system seems to no have libRCodec.dll.Having carried out a search on the web RegCure offered to rectify the issue,Naving Purchased,installed and tried the software I have found no improvement and as such contacted RegCure requesting a solution or my payment back.
View 2 Repliesi tryed to connect to my media extender
with the 8 figure code
but get the following fault code 545..
it will not conect to my linksys extender
Media Center Extender Setup cannot create an account for the Extender with ID:
uuid01CB97F-7D43-44DA-AC20-0682DDAAAE40.
Error: Access is denied.
My system restore on my PC running Windows 7 is not working, I get this error message- 'could not access a file, error ox80070005' whats going on and how do
View 2 Replies View Relatedevery 2 days i get this irritating message: "system error code 8, not enouge storage...." this happens when i try to close programs , when i try to open a program or even to open a browser. therefore, i need to restart my computer everytime and then it works fine for a day or two.....i have plenty of space in my hard disk.i tried several things ( that i read here) but it doesn't: i used registry booster program but, in vain....
View 9 Replies View RelatedComputer was running fine until I used a safe mode windows firewall sweeper in order to get rid of this nasty Trojan horse. The program ran fine and it delete just the Trojan horse "no other program or files were removed" I've tried several times to system restore but still the same error message.
Is it possible it did something to my registry and can clear CMOS work to fix it? I cannot get past the system restore screen and the bios screen can also get command prompt.
I have recently installed Windows 7 to my HP dv2718us and am missing drivers.For all listed below I get "The drivers for this device are not installed. (Code 28)"
Base System Device
Location: PCI bus 1, device 9, function 2
Base System Device
Location: PCI bus 1, device 9, function 3
Coprocessor
Location: PCI bus 0, device 1, function 3
Running updates for drivers have been unsuccessful. It seems important.
I am trying to rectify the error with windows update. Everytime I try to update it tells me it is checking for updates...Then "To check for updates, you must first install an update for Windows Update. Your automatic Updating settings will not change." I click Install now and get "Window could not search for new updates"An error occured while checking for new updates for your computer. Error(s) Found Code 80070643 Windows Update encountered an unknown error.
This problem first came to light a year ago when I downloaded a windows update that was corrupt.It forced the computer to loop the autocheck upon boot and could only be started in safe mode or by canelling the check.After looking through the forums I found an interim fix which disabled the autocheck and since have always recieved the message upon restarting "Autocheck program not found".I naturally thought this issue would be resovled in the next update and or a future fix.I had to go away for work at the start of this year and when I got back and windows updated it still had the autocheck message.Recently I have been unable to update at all due to the aforementioned error. The simplest soultion it would seem would be to do a system restore, this I have tried however every possible point seems to have a corrupt file on it.I ran a scan using Malwarebytes and found nothing.I don't want to format as the programs came pre installed and that would mean taking to back to the shop.
I�m running a single Windows 7 Ultimate x86 OS on my laptop and it used to work very well �till earlier today once I get back home trying to use my computer as usual to find out that it always runs the startup repair after showing the words �windows is loading files� instead of starting windows normally. Once the diagnostic & repair process is done it tells me that Startup Repair cannot repair this computer automatically. When I view the details I get the following under Root cause found:
Boot configuration is corrupted.
Repair action: Partition table repair.
Result: Failed. Error code = 0x490
After many times doing the previous repairs with no result I went to Command Prompt in order to check my system drive to find out that both �Windows� & �Program Files� directories are not existed there anymore. Instead, there�s a �Windows.old� directory that contains those 2 system directories as well as �Users� & �PerfLogs� directories plus the �autoexec.bat� & �config.sys� files. Sure there�s noway to use the system restore tool or anything else even using my Windows boot DVD. Still can�t use the cmd commands single handedly to fix this.As I said earlier I have never faced such problem before plus I have no idea how to regain my windows since I can never format my system drive as I need to backup all the files, settings, bookmarks & favorites located in my user profile first.
I have just installed windows 7, and this screen thing is very irritating. It happens if i try to open a picture file, a game, a video etc. I have to restart my computer every time and it's so enoying. My graphic card is a GeForce 7950 GT.
View 7 Replies View RelatedI have done everything I can to figure this out and I can't seem to. The RAM has no errors on MEMtest x 3; I have re-installed windows and I am getting the same error. Hardware or software?
View 5 Replies View Relatedi have tried and tried with no luck the memory is ok the hardisk ok every thinh seems ok all the drivers up to date and i have installed everything in windows update i had enough i will leave it for the professoinal to solve it so please guys i need your help i have attached the midumb how to get rid of the blue screen ( page fault in nonepaged area.
View 3 Replies View RelatedMy Specs...
AMD Phenom IIx6 1090T Black
ASUS M4A78T-E
4GB 2x2 DDR3 G-Skills Ripjaws
Windows 7x64
Nvidia GeForce GTX 460
SSD Main and 1TB alt
...if i forgot something tell me
This error started when I was gaming i dunno how to post batch reports but I ran memtest86+ and found 1 of my 2gig sticks was faulty and i pulled it. I thought this would solve the prob but... I also ran dskchk and it fixed a few threads. I can get online and watch shows or movies but I can't play my favorite games. Also sometimes my ssd won't recognise in the system.
I fitted a new hard drive and re-installed the OS for this client. After a couple of weeks it started to blue screen. At first I thought their usb wireless adapter was at fault. I removed it and everything was ok for another week or so. Then the BSODs started again.
I have tested the RAM and HDD - both fine. I have used Eurosoft PC-Check to stress test the machine and it was fine. I used the same software to test the motherboard and it passed fine. I used Prime95 64 bit to torture test the machine and again it wouldn't crash. Also I have run mbam and superantispyware and the machine is spyware free. It also has the latest video drivers installed. Typically since I brought it back to the office it has behaved impeccably in every way
While I had Autodesk Inventor2012 and Acad installed and running for months, I woke up a few days ago with everytime i would open the program, I would experence a Blue Screen Crash wih the following code( page_fault_in_nonpaged_area) STOP:0x00000050 along with a hole string of additional (0xFFFFF8801306F2E0, ect, ect, ect)?
View 2 Replies View Relatedgot blue screen with message page_fault_in_nonpaged_area
View 1 Replies View RelatedI've been getting the BSOD "Page fault in non paged area" a few times every day on my laptop and I don't have a clue why. I've had this laptop for around a year, and it has only just happened once I've got to university. I haven't changed any hardware or installed any new software recently and the only thing I can think of that has changed is that I am using my accommodation's wired internet - but I don't know whether that could cause this or not.
View 5 Replies View RelatedIm getting a Bsod for page_fault_in_nonpaged_area bsod
View 1 Replies View RelatedI got an HP laptop in September and have had a problems with the system fan within a month. Got the battery replaced for the fan and now I'm having a number of BSOD's. From watching videos online, startup and shutdown, to installing updates. They are happening everywhere. Best Buy told me to do a completely erase everything. So I used the OEM / system recovery on the laptop and started off fresh, but I'm still getting same BSOD's. I purchased a new laptop in hopes of selling this one, however, my new one was stolen yesterday. So, I'm back to trying to work with this one and figuring out the BSOD's.
View 7 Replies View RelatedMy comp recently BSOD
Computer Spec:
Intel C2D E7500 2.9GHz (OC'ed to 3.6Ghz)
Kingston 2 x 2GB DDR2 RAM
Asus P5Q SE2
Inno3D Gtx 560 Ti
Windows 7 Ultimate x64
i think its due to my HDD. Drive sentinel says:
The drive tried to examine and reallocate data sector(s) 7 times. The examined data area is perfect. Problems occurred during the spin up of the disk 1 times. This can be caused by the disk itself or huge power load (weak power supply). There are 25 weak sectors found on the disk surface. They may be remapped any time in the later use of the disk. 8466 errors occured during data transfer. This may indicate problem of the device or with data/power cables. It is recommended to examine and replace the cables if possible. At this point, warranty replacement of the disk is not yet possible, only if the health drops further. It is recommended to examine the log of the disk regularly. All new problems found will be logged there.
Seriously not a power supply issue. since it's 600w true rated. Checked the cables too. Oh i plugged in an external HDD too. Is this related?
I had to recently replace my RAM due to multiple BDOS error involding it including this one. I am now using 2 4GB kingston RAM stick but am still getting this error. I reformatted my computer less then 4 days ago and only installed a minimal amount of programs. i have done a chkdsk, updated and re-installed all my drivers, run a memtest86 test and even tried to run the computer by switching out the RAM, but I still managed to get the error. I have installed all windows updates and haven't overclocked anything since getting this computer. Before this I experience a MEMORY_MANAGEMENT error but that was fixed as soon as I replace my RAM.
View 3 Replies View RelatedIm getting restarts due to BSOD usually when accessing many files such as during antivirus scans or backups.
Windows 7 x64 ? - full retail version
- What is the age of system (hardware)? 3 years
- What is the age of OS installation (have you re-installed the OS?) 1 year
So lately I have been disconnected from the internet every now and then. Usually I just power cycle my modem and router and move on. But today it happened twice so I need to figure out the problem. I powered cycled the modem alone, and I still had no connection. I power cycled the router and I had connection after so I'm assuming it's the router to blame. The router plugs into my modem, and the ethernet cord from the router goes into one of these: Amazon.com: Dynex DX-EHB4 - Hub - 4 ports - Ethernet - 10Base-T - DC power - external: Computers & Accessories. My PC, Xbox and PS3 are all connected to that. Also during this time my iPhone couldn't get internet through WiFi. I have the D-Link DIR-655 as my router.
View 2 Replies View RelatedI just build a new system,
core i5 2500
asus nvidia gtx 560
gigabyte ga-b75m-d3h motherboard
G.Skill NT DDR3 4 GB (F3-10600CL9S-4GBNT) ram
Seasonic s12 520 w psu .
when i installed windows 7 32-bit everything worked fine for 2-3 days then i started getting bsod's, then installed windows 7 64-bit and after 3 days again bsod, when i start the pc. after loging in bsod appears, and pc restarts after that everything works fine.... i also did run a memtest for 11hrs not a single error found.
lately i have been getting quite a number of BSODs, even though there were no hardware changes.
error code : 0x00000050
according to the bluescreenviewer, it was caused by ntoskrnl.exe & ntfs.sys took out my rams, cleaned the 'golden' area. makes no difference
Last week i brought to your attention i was having dxdiag and atikmpag errors. I have resolved that by purchasing and using a Nvdia gtx560ti and the tech support people i bought the previous 6950 from advised me that they have come across a lot of problems with the Asus version of the card.With the new Gtx560ti, i purchased another 4GB of the Kingston HyperX pnp Ram. Since, i was getting random BSODs relating to "page fault in non pages area". I resolved this by removing the ram stick in Slot 4 of my Motherboard. After a few successful attempts, i reconnected the "suspected" Ram stick in Slot 3 and put another stick in Slot 4Since, i have not had a problem with page fault in nonpages area BSODs.
However, i am now beginning to get PFN_LIST_CORRUPT. What i would like to know is if this is related to the "bad" ram stick or a driver problem. I use the Uniblue Driver Scanner which is unable to find any outdated drivers. Can you look at Note that i used the Windows 7 memory diagnostic test and a pfn list corrupt BSOD occurred at 99% completed.At 98% it still showed "no errors have been found".
HP Pavilion a4316f-b, Home Premium, 64-bit
The PC was displaying symptons of page hijacking, so I ran MalwareBytes and got rid of 17 objects. Did not make a difference, so I ran TDSSKiller. It found 1 bit of malware but the hijacking persisted. I downloaded ComboFix and ran it in Safe Mode. It gave me some sort of error that was only visible for a split second before it disappeared, leaving only the initial small blue CF box, which stopped functioning, and I noticed that the CF task was gone. This happened 3 times in a row.
I then tried a system restore to about 3 weeks ago. It probably sat on the 'restoring files' screen for a half hour before finally saying 'Shutting Down'. After 45 minutes of (not) shutting down I pressed the power button and turned it off.
A restart brought me to the Windows Error Recovery Screen where I am presented with but 2 choices - Launch Startup Repair or Start Windows Normally.
The 'repair' option takes me to a Windows Boot Manager screen which prompts me to insert the install disk and reboot, indicating that The boot selection failed because a required device is inaccessible
So I use the CD. When booting from that CD I can see it loading files, then it says Starting Windows, the initial blue sky screen displays for a few seconds - then the BSOD: PAGE_FAULT_IN_NONPAGED_AREA with an 0x50 code. This always happens with this disk.
A different Windows 7 CD has given me the same start up to the blue sky, but with 3 different BSODs. One had Bad Pool Header and the other said An attempt was made to write to read-only memory and the 3rd had the same PAGE_FAULT_IN_NONPAGED_AREA
Only 3 of the 4 choices presented to me at HP opening boot screen seemed to work when I first started this awful task. F11 for Recovery did nothing. I DID use f9-Diagnostics and it passed all the tests. Now, sadly, the only option that works is ESC to change the boot order.
I just got a BSOD. I think it's about my memory or hard drive. I have attached the required files.When the crash happened I was streaming from netflix using Firefox, working in Word, Outlook was also open.This time it created the minidump file. Code: Is Windows 7 . . . - 64 bit - the original installed OS on the system? Yes - an OEM or full retail version? TechNet download - What is the age of system (hardware)? 2 years - What is the age of OS installation (have you re-installed the OS?) May 2011
View 3 Replies View RelatedI've installed Windows 7 Ultimate 32bit on a HP Pavilion Laptop model dv9292eu by backing up my work and formatting the HDD. The issue I am having is that I cannot seem to get the Nvidia Graphics driver to work. I downloaded the most recent driver for the Nvidia Geforce Go 7600 from Nvidia site and I get the blue screen so I have now uninstalled the driver and gone back to standard VGA.I have also searched this forum and I came across the following thread which assisted me in the past with a Sony Vaio laptp.
View 3 Replies View RelatedI just bought my new laptop 1 month ago, but BSOD occurred for many times.Window 7 Home Premium
System
Manufacturer Hewlett-Packard
Model HP G42 Notebook PC
Total amount of system memory 4.00 GB RAM
System type 64-bit operating system
Number of processor cores 2
Storage
Total size of hard disk(s) 596 GB
Graphics
Display adapter type ATI Mobility Radeon HD 6370
Total available graphics memory 2746 MB
Dedicated graphics memory 1024 MB
Dedicated system memory 0 MB
[code]....
I have a computer as described in my profile and ive had it for about a year now. about 6 months ago i occasionally got BSOD and ignored it Then i upgraded the ram to 16gb (was origionally 6gb) and it was great (ran so smooth) but recently ive been getting this BSOD more and more frequent and now the pc is quite unuseable.
i searched up online and found that it could be software, ram or hardrive most probably so first i tried a factory restore and still got bsod and freezes then i tried factory restore once more... no luck then i downloaded a home premium iso installed that and it appeared to be working then that started doing it.
next i tried Ram first i downgraded it to 8gb then swapped it back to the 6gb it came with none of this helped
now i think it must be the harddrive or something wrong with the motherboard. since i cant use it atm im quite ****** off (Ps:the blue screen error message is "Page fault in non paged area" every time)
I have been trying to fix this computer and i cannot get this BSOD to go away. I have installed new RAM and re-installed windows to no avail. I have updated the drivers for the video card and the cpu.
View 3 Replies View Related