I recently reformatted and reinstalled Windows 7. I have another drive with Windows XP on it. Before reinstalling 7 it offered to boot either Windows 7 or "Older Version of Windows". Now it recognizes the drive, it even recognizes it as being named XP but it will not offer to boot to XP. I tried going into the BIOS and shifting that drive to the second boot device behind the drive containing Windows 7
View 7 Replies
the vista and win7 both has retail version,n it is 30days trial...for which lots of cracks n activators are available.i just want to know,i am trying dual boot,having win7 on C n vista on D partition,n both are activated by crack...but problem is,as long win7 is only OS,its activated but as long i install vista on D n apply crack,vista gets cracked but win7 on C again reverts to 30day trial.as i felt,this might be cause of installing win7 on C n vista on D,i mean oldest OS must be 1st,i dun know i m saying right or wrong.
View 1 Replies View Relatedi have a new work laptop with xp sp3 on it. I want to install w7 64 bit as a dual boot, but only have 1 physical drive. i cannot remove my current installation as it is pre-build from work, but can partition the drive etc. However on trying to install w7 64 bit I get a message saying cannot install windows 7 on efi drive with mbr, not gpt. Can I do what I want without screwing up my xp installation?
View 5 Replies View Relateddual booting windows 7 home premium x64 with linux fedora 14 on dual independantly dedicated drives. i am a college student with moderate computer (windows) knowledge but am doing software development and would like to play around with some linux for a class. i have no prior experience with linux and have minimal knowledge of operation. i am currently running windows 7 and would like to keep it as my primary os. i do not wish to share media files across drives or os's, windows does that just fine as is and i dont want to get into a third drive. my current drive is a 1tb wd black caviar hdd. it is also currently 2/3rds full and the desktop is about 6 months old so i would rather not partition the drive for a dual boot. i would think that there are some other advantages for the os's operating independantly off their own drives other than if one hdd dies i should still have the other with its os still ok. i have read some topics about RAID configs with dual boot setups with dual drives like this but am not very familiar with RAID. is there a RAID config that would be beneficial in this situation? i currently do not have a RAID card. my tower internals are not very accessible and i dont like the idea of disconnecting drives depending on which os i want to operate.
View 5 Replies View RelatedAs currently configured, XP is on drive C:, Win 7 was added to drive E:, and the system is currently run as a dual boot. Attempting to boot without the XP drive present will yield a "NTLDR is missing" error very early in the boot process.
I have already tried the following:
(1) I moved the hidden Windows Boot Manager files (bootmgr as well as the associated Boot folder) from the XP drive root to the Win 7 drive root.
(2) After physically removing the XP drive, I rebooted to the Win 7 installation DVD, and used the "Repair Your Computer" option to pull up the "Recovery Tools". Then, using the command prompt utility, ...
(3) I attempted to write a new boot sector to the Windows 7 disk using the command: Bootrec /fixboot, - that yields an error though. The Bootrec /fixmbr claimed success, but ultimately did not make Win 7 drive bootable.
I had to reconnect drive C: just to boot into Win 7 again to write this. I do have files backed up, but to format and reinstall files would take many hours beyond just the time to transfer 400 GB of data, since I have dozens of purchased applications that need to be freshly reinstalled and validated as well. Basically I want my E: drive now to be my boot drive while the C: drive is reformatted and used for general storage.
Any idea how to make my Win 7 drive bootable? Do I need a partition program that is more adept at creating a viable boot sector, or is that even the problem?
I have Win XP 32 bit on my old drive. I buy Win 7 full retail and a new HD. I set bios to boot from cd etc. Win 7 starts up. It shows the 2 drives, so I select new drive...no problems. It starts install. I leave it to do its stuff.When I come back its up and all ok.I dint get any option to boot from XP. The drive was listed as "SYSTEM" but not old Windows or anything.
Also ASUS chipset drivers dont work and they were listed as 7 drivers.I tried Vista drivers but it normally shuts down and restarts. Nothing.
I installed Windows 7 on a partitioned harddrive with vista on the other half. After the installation i have my boot menu with:Windows 7, Windows Vista, Windows vista still works but when i try and load windows 7 i get a boot error message
View 9 Replies View RelatedI have XP (x86) installed on one partition.
Last night I installed Windows 7 (x64) on a separate partition.
Anytime I had tried this in the past, using Vista, it always detected the Windows XP partition, and gave me a boot menu with "Earlier Version of Windows" option to boot to.
This is not so with Windows 7.
How can I get the boot menu to show both options, to boot to XP or to Windows 7?
I have dual boot with Xp and windows 7.when i log into my Xp all the restore points being deleted from windows 7.when i check the disk management information in 7 it shows windows 7 create a logical drive with my Xp primary drive.even i am hide the drive from both windows means Xp drive from windows 7 and vice verse.So i like to unmount or remove the drive partition of windows 7 from Xp and Xp primary from windows 7.So that they dont affect each others system files with being deleted the partitions.
View 1 Replies View RelatedI installed opensuse 12.1 on dual boot along with my other windows 7 installation. Installation of opensuse is successful and i can use it. But when I tried to use windows 7 on grub, it says bootmgr is missing. I've already encountered this problem a long time ago so i tried to use bootrec /fixmbr, bootrec /rebuildbcd and bootrec /fixboot in the recovery console in the windows 7 DVD. Rebuildbcd and fixboot did not work and it said something like it cannot find my windows installation. I also tried bootrec /scanos, it returned a windows installation on D:\Windows but my windows is in drive C. I think this has something to do with me messing up the active partition in disk management a month ago but i already fixed it by setting the active partition to the system reserved partition. Only fixmbr is successful, but now i can't boot on any OS because it says: Missing operating system.I also tried bcdboot C:\Windows but it failed with a message that goes like: Failure when attempting to copy boot information..
View 2 Replies View RelatedI was having win 7 RTM and i tried to installl OSx86 in second hard disk
after few failure i successfully installed OSx86 in my secondary had disk now the problem is that i cant boot win 7
i changed boot order i tried windows 7 disk repair
but both failed
im getting some Boot mldr missing...
Actually even OSx86 is not booting i get OSx86 boot screen with two hard disk to select if i select windows disk it still says the same Boot mldr missing.
I can't get Win 7 to boot after setting up dual boot (Ubuntu 10.10) on my GF's laptop. I'll describe the problem and everything that has been tried so far. REALLY hoping somebody has an idea, I'm getting desperate.I installed Ubuntu last night via the Live CD. Used the Live version to install alongside Windows and partition the drive, install Grub, etc. At reboot, after POST it would just go to a black screen with a flashing cursor. I could only run off the live CD. A forum member determined the Grub was trying to load from the wrong partition. We changed that and voila! Grub now loads properly. I can boot into Ubunto via Grub with zero problems. HOWEVER: when I try to boot into Win 7 from Grub, it just locks at the same flashing cursor of death screen. The 7 partition is till intact, I can see and access all the files on the 7 partition from within Ubuntu, however 7 will not boot. I have tried downloading and burning the Win 7 repair disk and doing all of the following,Running the automatic Start Up Repair - several times. All it does is remove Grub, but booting still goes to the flashing cursor and I have to reinstall Grub again to be able to do anything after POST.I have used the command prompt to run "bootsect /nt60 SYS /mbr". Has the same effect as above.I have used all the bootsec.exe /fixmbr, /fixboot, and /rebuildBCD commands. Again, all have the same effect and I have to reinstall Grub to get anywhere.I don't have an installation disk to try and just do a repair install because Asus apparently doesn't feel that I would need one of these. All I have is the recovery disks from the Asus AIRecovery application that want to just re-format the entire drive and start over. This isn't an option. It's my GF's laptop (mine gave up the ghost last week) and we both have WAY too much highly important data on here. Not to mention she would castrate me . Now from all my research the only other thing I've come across that sounds possible is that the boot flag needs to be set to a different partition. Somebody had a somewhat similar problem and it turned out the way Dell set up the system the boot flag had to be moved to a recovery partition and it worked fine. I'm wondering if Asus has something similar going on, but I can't figure out how to move the boot flag. I'm going on 12 straight hours of working on this now
View 9 Replies View RelatedI setup an XP/Windows 7 dual boot on two drives. Currently C: Windows 7, D:XP
Love Windows 7 and now I'm ready to convert to single boot Windows 7.
I'm not real savy re. bcdedit so will need very detailed instructions
I did find the command line in Windows 7 by going through accessories but I'm scared to go further without help.
Eventually I want to clean up the D:xp and use it for storage etc.
I'm guessing this procedure may have already be written up but I can't seem to find it.
How to Change the OS Name in Windows Boot Manager ?
View 0 Replies View RelatedI recently added a hard drive to my computer (SSD), and installed Windows 7 x64 onto it. The result being a dual boot system, which by default boots to the SSD, and optionally (by Windows Boot Menu), can be booted to the original drive (standard mechanical drive).
Initial setup went fine, however I decided to customize the Windows Boot Menu, so that logical names could be associated with each operating system instance. To do this I used EasyBCD and I altered the names in the Windows Boot Menu from: Quote:
Windows 7
Windows 7
to... Quote:
Windows 7 - SSD
Windows 7 - Standard Drive
Shortly after the modification I noticed that I was no longer able to boot into the original OS. Instead I was being presented with a "Repair Windows" option. Figuring that my EasyBCD "tampering" may have had something to do with the issue I decided to change the names back to "Windows 7" in the Windows Boot Menu. However doing so had no positive impact on boot up of the original OS.
After booting again into the original OS I accepted the "Repair Windows" option, and then left the computer over night to do it's "thing". After completion of the "Repair" the situation has deteriorated -
* Windows doesn't load (the same as before)
* Windows doesn't present a "Repair Windows" option (it did before)
* The computer reboots a short period after the "Starting Windows" screen is presented
As a side note the drive is in good health, and all data on it can be read from within Windows 7 when I boot to the SSD OS.
I have installed a year before UBUNTU on my pc with dual boot (i.e. use either window 7 or ubuntu).the NTFS partition that contains the UBUNTU was corrupted and i wanted to take the dual boot from my PC. I used the instructions from the web site: http://www.makeuseof.com/tag/how-to-...t-environment/but the disk management tool would not let me delete the NTFS partition.Could any one help me delete the NTFS partition and use just windows 7 as the only boot. step by step help would be great.
View 8 Replies View RelatedI got windows 7 running fine for a while now and ever since my XP did not boot anymore.I was not worried to much about it since i did not need it at the time.But now i really REALY need it,See i got all my Cubase projects in there and my cubase plug-ins al setup in XP and i need to get to the projects?At first it did not do anything and using easyBCD did not help either.I cpoied ntldr and detect to the root of C: wich contains my XP and now it shows the bootscreen but hangs on a black screen.The thing is right before the bootscreen shows i see the text" invalid boot.ini" flashing by very quick.I am able to enter that winXP install in safe mode and i tried safe/vga mode as well wich works but thats all.
View 9 Replies View RelatedI have a laptop I bought a year ago on which a created a dual boot Win 7 (32bit)/Win XP SP3 install, each on a separate partition. It was my first Win 7/XP dual boot install, and my first personal system that I allowed to have a Win 7 install on it at all, so although I have plenty of experience working on pretty much every previous version of Windows, I have very little experience with Win 7 and dual boot configs.
Today about 2 hours ago my audio spontaneously stopped worked for no good reason, so after shutting down each program to see if that cured it (which it didn't), I restarted the system. Out of the blue, for the first time I've ever experienced it, I received the msg "MBR Error 1" - Press any key to boot from floppy. I don't have a floppy of course on my laptop, and if I press any key I simply get the same msg. I turned the system off for a few minutes to make sure it was a good cold boot, but every time I still get the same msg. I tried switching the BIOS setting from IDE to AHCI (IDE is required for XP to boot, AHCI required for Win 7), but I still get the same error msg before I'm even prompted with the OS boot selection, so it made no difference of course.
I looked up this issue and found various suggestions, but none of the ones I found took into consideration a dual boot config., they were all Win 7 specific solutions. I don't what to try and repair the MBR only to have it screw up my dual boot config and be unable to access XP, which is what I use almost exclusively, nor do i want to lose access to Win 7 if at all possible.
I had a backup HD of my complete system that I saved several months ago when I upgraded my HD, and I periodically refresh the most important files on it, so I'm currently running on the laptop in question using my old HD, and it's working just fine. Worst case I can just clone my old HD to my newer HD that's screwed up, but I'll still lose a lot of changes I've made to the OS since I upgraded the HD and have to reinstall and config a number of programs, so that's my last option. I'll also have to back up about 200GB of data from the newer HD which is much larger than my old HD, and then restore it back after the clone, something that will take a lot of time and unncessary effort if I can just fix the MBR.
I'm having a problem every time I power on the system. I'm dual booting vista ultimate with win 7 build 7100; with vista I have no problem, but with 7 every time I start the system the first boot attempt gives me the error 0xc000000e after the boot manager display: "the boot selection failed because a required device is inaccessible".;after a reset the system boots 7 with no problems. Win 7 is installed in a brand new hd(seagate barracuda 1.5tb) and vista on a second hd.
I've search the web for people with a similar problem with no success. I've tryed already many solutions but the problem persists(latest bios for the motherboard, latest intel sata drivers, etc). I'm hoping that this could be a bug in win 7 instead of a hardware failure for the hd. Again, the strange thing is that this only happen after the power on. After that first error, no matter how many reboots, the system always boot without problems.
i did a terrible mistake. i installed windows 7 first on one drive and then i install windows xp on separate drive. and when i restart there was no boot menu to choose the OS from list only windows xp started straight away. i did not knew about EasyBCD . and i put my windows 7 DVD and run recovery. now i can goto windows 7 but xp is missing again. is there any way i will not install xp from beginning and windows 7 can add boot menu in startup to choose xp or 7.
View 4 Replies View RelatedI recently added a hard drive to my computer (SSD), and installed Windows 7 x64 onto it. The result being a dual boot system, which by default boots to the SSD, and optionally (by Windows Boot Menu), can be booted to the original drive (standard mechanical drive).
Initial setup went fine, however I decided to customize the Windows Boot Menu, so that logical names could be associated with each operating system instance. To do this I used EasyBCD and I altered the names in the Windows Boot Menu from: Quote: Windows 7 Windows 7 to... Quote: Windows 7 - SSD Windows 7 - Standard Drive Shortly after the modification I noticed that I was no longer able to boot into the original OS. Instead I was being presented with a "Repair Windows" option. Figuring that my EasyBCD "tampering" may have had something to do with the issue I decided to change the names back to "Windows 7" in the Windows Boot Menu. However doing so had no positive impact on boot up of the original OS.
After booting again into the original OS I accepted the "Repair Windows" option, and then left the computer over night to do it's "thing". After completion of the "Repair" the situation has deteriorated -
* Windows doesn't load (the same as before)
* Windows doesn't present a "Repair Windows" option (it did before)
* The computer reboots a short period after the "Starting Windows" screen is presented
As a side note the drive is in good health, and all data on it can be read from within Windows 7 when I boot to the SSD OS.
I have xp 32bit and 7 64bit on a dualboot and 7 is the default, however I want to change that.
View 7 Replies View RelatedI had Win XP and Vista set up as dual boot. I have back up images of both using Norton Ghost. I then upgraded the Vista partition with Windows 7 RC and all was fine for several months. Last week I had issues with the XP installation and the only resolution was to put the xp image back on the xp partition. This action has left me with a boot screen with XP and Vista on it and as expected only XP can be booted.
I put the Windows 7 installation disk back in and it recognised the boot screen error and fixed it; (too good to be true I thought!) When booting, I got the choice of XP or Windows 7, so the Vista option had been replaced ) however, there is an error that cannot be fixed and so the boot fails. The PC does the usual reporting to MS looking for a solution but can't find one.
So, will I have to replace the Windows 7 partition with the Vista image and then reinstall the Windows 7 or can I recover this another way? Also, what is the best way to image, individually, OSes, so that the boot screen doesn't get changed?
When my computer wouldn't turn on in the morning I did the usual diagnostics; unplug things one at time test with spare components etc... Any way I qucikly figured out the PSU was dead so I ordered a new one and was back up and running. However when I reassembled the computer after unplugging everything (and removing the m/b) I plugged the HDDs back into different SATA ports from which they orginally came. When I came to boot the computer up I got the error message: 'BOOTMGR missing' or it may have been 'NTLDR missing' I can't remember.
I fixed this problem by using the 7 startup repair utility. I have no problem booting into Windows 7, but I have lost the option to boot into my XP install on anther disk. I looked in the boot tab under System Configuration and the only OS showing is this Windows 7 install. So my question is this: how can I get the choice of which OS to boot back?
(I should mention that the XP install is on a different disk from the 7 install).
I've a Dual Boot with Xp/Win 7 on my office Desktop workstation. Window7 is the beta version of the Win 7. And like all other companies.... my company also want it's wallpaper and screen-saver on each machine ..... But i somehow manage to install Window 7 on my office Desktop.
Now i want to remove Window 7 partition and restore my Xp MBR and that too without using Windows Xp Bootable CD ( as CDs are not allowed in my company )...
How can i restore my Xp MBR while accessing my Xp Partition as i already have deleted my Windows 7 partition .
ok so im having a weird problem thats probably very easy to fix.
background info: before my Windows 7 install i had 3 partitions
vista 64
xp 32
empty (soon to be linux)
when i downloaded the newest win 7 build i deleted my xp 32 partition and installed Windows 7 on that partition. because Windows 7 creates that "reserve partition" or what ever, it extended my EMPTY partition with my vista partion. which cause it to become a "logical drive" rather than a "boot" drive. aka i cannot figure out how to access my vista OS.. rather annoying since im just toying with Windows 7 atm.
I had Win XP on 1 HDD & installed Win 7 on a different HDD. I think I accidentally did a dual boot install because Win 7 won't boot without the the XP disk connected to the motherboard.
That was fine until my XP drive died yesterday. Now Win 7 won't boot. The first time I tried to repair, Win 7 was not even seen. so I booted into diskpart and made the partition active. Now it could be seen as an OS.
Then I did a startup repair. It did whatever it does & when it was finished I restarted the pc but it didn't boot I went back to diskpart and confirmed the partition was active. I went back startup repair and tried again.
This time it said it could not detect a problem, but it still will not boot. What else can I do? My pc is homebuilt. Right now I have the 1 sata drive, 2.53 ghz cpu, 4gb ram, onboard video & sound
[code] I recently upgraded from Windows XP to Windows 7. Inside the bios of my computer is an option to use the onboard graphics controller or to use the graphics card installed on my PCI Express slot. If I select the PCI Express option, the motherboard automatically disables the onboard controller before it even reaches the OS and so it is impossible to extend my desktop. The only way to fix this issue would be a bios update. Anyway, here is what I did instead on Windows XP. I would just use the bios and select the option to use the onboard graphics controller. The OS would start and use the onboard video card and would then detect the graphics card (with the proper drivers) and detect the monitor attached to that card. I would then successfully be able to extend my desktop to the other monitor select proper resolution and even choose which monitor is the default monitor. Thus we have dual monitoring. Now that I have upgraded to Windows 7 I can't get this setup to work.
If I use the bios and select the graphics card option, then in Windows 7 the graphics card is detected (and installed with proper drivers) and the monitor that is attached is properly installed. Inside device manager everything looks perfectly fine (no yellow things), except that the onbaord graphics controller is not detected (but that is to be expected, since that also happens in the XP case). If I use the bios and select the onboard graphics card option, then Windows 7 starts up with the onboard graphics card (with proper drivers installed) and the monitor attached to that port works fine. However, it does not seem to detect the graphics card. Inside device manager, under displays it lists the onboard graphics controller and the GeForce graphics card as properly installed and working. However, it also lists a new, unknown video controller?!???!!? Is this the graphics card again? Does it need more drivers? I can't get the computer to detect the monitor on the graphics card. Apparantly this seems to be an issue with Windows 7. Both monitors successfully work on both graphics controllers (the PCI Express and the onboard), just not at the same time. I don't think this is some type of drivers issue, but I am no expert.
I have two graphic cards and Win 7 will only let one work at a time. I have updated the drivers both to windows 7.
View 8 Replies View RelatedAfter I installed Windows 7, I had by tv connection still showing as a second monitor. Just the other day the display no longer shows anything but the sound is still coming from the tv. In properties the display only shows 1. I also tried detecting and nothing happened. I have a Radeon 9000 video card.
In device manager, other devices is showing video controller with a yellow !.
Monitor is showing - Generic Pnp Monitor
Display is showing Radeon 9250 9200 series
I just installed Windows 7 pro 64 bit on the system I built tonight, and only one of my monitors will work. I installed the latest drivers for my ATI 5770, and windows is recognizing both monitors, but only one comes on. The other stays in standby mode. I made sure both monitors are enabled.
If I switch the cables in the back of the video card, then the opposite monitor works. I can also drag monitor 2 to the left of monitor one, and it takes the taskbar away from the working monitor as expected, moving it to the monitor that won't turn on. Has anyone seen this issue before?
