Dual Boot Windows 7 / Installing XP On Separate Partition - Chkdsk Error
Oct 17, 2012
My computer has windows 7. I created a separate partition on my hard drive to install windows xp, but now when I try to install it I get an chkdsk /f error.
I have read that using a computer specifically for financial transactions with known and trusted entities (such as a bank) is a good way to reduce (though not eliminate) the risk of your accounts being hacked by reducing the likelihood of inadvertently installing a malware, spyware, or virus by reducing internet sites visited. Assuming this is correct, I was wondering about dual booting one computer with two physical hard drives (each with its own OS) versus one hard drive with two partitions. I figure the former would be "more secure" since one drive would be isolated from any unwanted programs. However, since they shared a few things (motherboard and such), is this set up as "secure" as having two computers? If so, how does one go about setting up a dual boot with two separate hard drives of the same operating system using one computer?
I have got two separate hard drives one running Windows 7 one running xp. I need to be able to chose which os to run but currently I can only do so by pressing F12. I have tried EasyBCD but it wont work - does anyone know how I can do this?
i used win 7 and wanted to install xp as a multi-boot on my laptop for trying an xp based encyclopedia but when i installed xp i got error "ERROR LOADING OPERATING SYSTEM" so i reinstalled xp and realized that i cant see my 2 25 gb partitions full of data,so kindly guide me to get my partitions back i have currently reinstall win 7.
When I go to create the new partition in Windows 7 that I want to install XP on it creates it as a logical drive. How do I create a primary partition instead?
I currently have Windows 7 installed on two separate drives in my box. I can only set (select) boot sequence in the BIOS. If I recall correctly, way back when a boot selection menu would appear when I think I was running Windows 7 (when it first came out) alongside XP but that screen no longer appears with my current setup. Is there a way to get that screen back, or an alternate way to select the OS of choice without the hassle?
I have separate ide drives one is installed with XP Pro and the other with windows 7. I want to have the choice of either os when the pc boots i.e. choose the drive to boot the pc.
I want to combine my 2 desktops into one, since I never use both together and the older one is very dated by now (think Time/tiny computers old). My current machine is an Asus P5Q-E with a C2D and has one HDD on a SATA connection running windows 7 64bit. The old computer is a single core Athlon 2700+ thing with a pair of hard drives on a single IDE ribbon.What I want to do is put the hard drives from the old machine into the newer and be able to choose between Windows XP already installed on the old master IDE hard drive and Windows 7 on the newer SATA drive (I've only kept the old computer to run XP for compatibility), all the while keeping the old slave IDE drive as a slave.
I have Window XP installed on Drive C:. My son installed Windows 7 on Drive E:. However, when the computer is booted up, it boots up in Windows 7, without allowing a choice. I suspect this can be corrected in BIOS, but don't want to screw it up.
i was wondering if i could get any tips or advice, i keep getting bsod error message when trying to install xp, it looks like i have to install the sata drivers, i think i have to slipstream the driver with xp as from my post here, but i cant find the sata driver for my toshiba hard drive anywhere. My sony vgn-aw120j does not have drivers for xp on the sony website and toshiba does not have drivers on theirs. my hard drive is a mk-3252gsx from toshiba,
I would like to remove Vista from my dual boot setup. Here is how I got to where I am now.
I had Vista installed on my PC hard drive (was C. Later, I decided to install Windows 7 HP on a new and seperate HDD. I unplugged the Vista HDD and added the new HDD and installed Windows 7 as if from scratch (I was worried that the install would mess up all my files on Vista). After the Windows 7 was up and running, I then reconnected Vista redesignated it as drive E: and after some searching on how to, I created the dual boot using my Windows 7 disk so I'm assuming the boot file in on drive C: along with Windows 7.
I now want delete the dual boot and Vista so I can use the drive as a backup drive or possibly Win8. I have found several methods to do this but none that really have my specific situation.
Is there an easy way to dual boot on separate drives, i have installed windows 7 on 1 drive & vista on another. This was done independenly on the same machine as to say put vista on last year the got another hard drive took the vista drive out put new hard drive in & installed windows 7.I connected both. they see each other.I have read lots about reinstall one OS but nothing on if its already installed. IS THERE AWAY?
I've done some searching for this and found some similar issues but nothing fits exactly what I'm trying to do. I have been running Vista Ult. 64 bit for a little over a year and have loved it. It solved all the problems I had with XP Pro 32 bit on my hardware. I bought 7 Pro 64 bit through www.theultimatesteal.com since I'm taking some night classes. I forgot I couldn't upgrade from Ult.
to Pro so I had to do a clean install, which I did, on a separate drive. I have five drives in my system, C, D, and E are all 1TB while F and G are 1.5TB. C is where Vista is installed and G is where 7 is located. I'll be going back and forth between the OS's until I get everything the way I want it.
At that point I want to remove Vista and have 7 be the only OS. But I do not want to migrate the install onto the 1TB C: drive, I want to keep it on the 1.5TB drive but have it recognized as the C: drive. The install was done from within Vista from the download since my physical media has not yet arrived. So even when I boot into 7, it is seen as being installed on the G: drive; it did not make itself the C: drive.
So I'll need to get rid of Vista, get 7 to see itself as being the C: drive, get rid of the boot menu, and swap the drives and cables around to put my 7 install at the head of the HDD pack. I've already done a full system backup of my Vista install with Acronis TIH 2010. How do I need to go about this? On another note; why did MS only offer home and pro through ultimate steal? They offered Vista Ultimate. I mean, it is called ULTIMATE steal, not Pro steal afterall, and it would have made the upgrade process that much easier.
I want to install 7 on a separate hard drive to see how it works & work indepenantly on it's own system. How can I if at all make it so when I am booting up I can toggle in between 7 & xp startups.
i have xp home 32 bit as my OS now and i have another hard drive installed and ready to install win 7 64 bit on to. can i do this with xp running or should i disconnect the HD with xp on it, then when i start the computer it won't see any OS and then i could boot from the win7 dvd and do a clean installl and then re=connect the HD with xp on it.
then when i start computer i should get the choice of which one to boot from or is this not the way to do it?? i want the OS's on separate HD's for now as i am sure that not everything that i want to run will work on the 64 bit win7 until i can afford to get all the programs i use to work on win7.
I currently have windows 7 ultimate in a Dell Gx270 P4 2.6ghz I know its old. And i want to Install Windows XP in another hard drive i have, but how do i make both hard drives boot, so i can select which one i want to boot.
I'm doing this because XP mode doesn't work in this computer. And i don't want to partition.
Most information i find in google requires partitioning and i don't want that.
If you know how please post it, or post the Links where i can find it.
I admit to being clueless when it comes to dual booting. I already have 7 X64 on my C: drive and a completely blank internal, formatted D: drive. How do I go about installing Windows 8 on drive D: and setting it up to dual boot?
I'm a long-time reader but new poster. I am currently running Windows 7. I want to install Windows XP onto another disc and have a dual-boot setup. I keep Windows 7 up to date and secure, but for the XP partition, I would rather not have antivirus running or even installed, in order to limit background processes. I will not be logging into any place or making any credit card purchases when booted into Windows XP. It will just be used for surfing, games, etc. Further, if and when XP becomes compromised or buggy, I will simply overwrite the partition with a backup image.
If I use Bitlocker to lock down the Windows 7 partition (with the encryption key on a thumb drive) and boot into Windows XP, am I correct in thinking the XP installation see or can't access the Windows 7 partition? If XP gets compromised, can a virus access or write to the Windows 7 partition?
Is there any other reason why this would not be secure? Can a virus write to the BIOS?
Wanna start off by saying sorry if someone has already resolved this problem on another thread but I have read many and haven't found a problem that exactly matches mine.Ok here goes, I have a Dell Inspiron 1764 running on Windows 7 64 bit. I've had problems with this pc for months in that it suddenly lost masses of disk space and because of this I couldn't update any programs or even renew my McAfee which I gAfter some investigative work with help online I found that my 'My Music' and 'My Pictures' folders were located on the C drive and taking up a lot of space so I relocated these onto the D drive. This seemed to solve the problem, the C drive was clearer and everything was working fine, security checked for viruses and all seemed to be in order.
That lasted for about 4 days and then yesterday the laptop randomly crashed and then restarted and it appeared to be ok, I continued using with no problems and switched off as normal. I tried to boot on again last night only for it to hang on the Starting Windows screen, didn't even reach log in. It went to a black screen and then something else came up and asked if I wanted to Start Normally or in Safe Mode, I chose Safe Mode.Nothing happened for a while and then it went into CHKDSK but sat at 3% for about 2 hours saying loads of files were unreadable, it finally got to 30% after 6 hours but by then it was 1 in the morning I had to manually turn the pc off.I tried again this morning and had the same error but it automatically goes into CHKDSK, after about 5hrs it got to 55% and then went back to the Starting Windows screen, black screen and the CHKDSK again, this has happened 3 times now.
I've tried pressing F8 & F12 when first booting up and I've also inserted the Windows Installation Disk but this won't run. I gave up and switched off again, went through the same process but when it got to CHKDSK I pressed to cancel the check but it just sat there for 25mins and then asked me to choose Safe Mode etc, I choose SM again and it started to load files and has been sat at Loading Windows Files for the last 15 mins.
This tutorial describes how to install Windows XP and Windows 7 on the same partition (first tutorial for one partition written).The short concept: Install XP twice and have 7 replace the first installation.Need more testers to confirm it works for everyone and the instructions are clear enough.Requirements: Both Installation discsA Windows XP LiveCD (might work with other OS, but no guarantees)EasyBCD.Install Windows XP normally if you're not already running it.Don't bother installing any drivers or software on it.Start another installation of Windows XP. Choose the same hard drive and leave it unchanged without formatting. When it asks you what to do then choose to install in a different directory "C:Windows.xp".Finish installing that one and only the necessary drivers.afterwards.Install Windows 7 on C: over the regular C:windows. A warning will tell you that it will move the old files to "Windows.old" directory. The good thing is it doesn't touch the Windows.xp directory.Install and run EasyBCD. Go to "Add/Remove Entries" and add an entry of "Windows NT/2k/XP/2k3" type and a name of your choice. (as shown in the attached image)Don't forget the "Save" button.You may also want to adjust the loader timeout from "Change Settings".In C: you will find a (hidden) file "boot.saved". Open it, remove the entry to the "WINDOWS" directory and make the "WINDOWS.XP" your default one (if it's not) and save as boot.ini".Restart and boot from the Windows XP LiveCD (which you should have burned and tested on CD or DVD before starting).Open the Command Prompt (Run "cmd") and enter the following lines in order
I installed Win7 on the same Partition as WinXP. I was in a hurry and forgot totally to partition the HD before I installed, was doing 100 things on the side during the Installation, and noticed my mistake only after the install was complete. Is there any way I can do a Multi boot for those two OS now? The WinXP folder has been renamed to Windows.old, and even with EasyBCD there's no way I can get the Comp to boot into WinXP.
I installed DOS into 2GB FAT 16, then installed Windows 7 Ultimate expecting Windows 7 to install itself in a partition with a drive letter other than C (just as XP had done in a previous dual-boot setting with DOS) But no, Windows 7 has hijacked the C drive letter for itself. How can I stop Windows 7 from "stealing" from DOS, the drive letter C, for itself?
I installed opensuse 12.1 on dual boot along with my other windows 7 installation. Installation of opensuse is successful and i can use it. But when I tried to use windows 7 on grub, it says bootmgr is missing. I've already encountered this problem a long time ago so i tried to use bootrec /fixmbr, bootrec /rebuildbcd and bootrec /fixboot in the recovery console in the windows 7 DVD. Rebuildbcd and fixboot did not work and it said something like it cannot find my windows installation. I also tried bootrec /scanos, it returned a windows installation on D:\Windows but my windows is in drive C. I think this has something to do with me messing up the active partition in disk management a month ago but i already fixed it by setting the active partition to the system reserved partition. Only fixmbr is successful, but now i can't boot on any OS because it says: Missing operating system.I also tried bcdboot C:\Windows but it failed with a message that goes like: Failure when attempting to copy boot information..
I can't get Win 7 to boot after setting up dual boot (Ubuntu 10.10) on my GF's laptop. I'll describe the problem and everything that has been tried so far. REALLY hoping somebody has an idea, I'm getting desperate.I installed Ubuntu last night via the Live CD. Used the Live version to install alongside Windows and partition the drive, install Grub, etc. At reboot, after POST it would just go to a black screen with a flashing cursor. I could only run off the live CD. A forum member determined the Grub was trying to load from the wrong partition. We changed that and voila! Grub now loads properly. I can boot into Ubunto via Grub with zero problems. HOWEVER: when I try to boot into Win 7 from Grub, it just locks at the same flashing cursor of death screen. The 7 partition is till intact, I can see and access all the files on the 7 partition from within Ubuntu, however 7 will not boot. I have tried downloading and burning the Win 7 repair disk and doing all of the following,Running the automatic Start Up Repair - several times. All it does is remove Grub, but booting still goes to the flashing cursor and I have to reinstall Grub again to be able to do anything after POST.I have used the command prompt to run "bootsect /nt60 SYS /mbr". Has the same effect as above.I have used all the bootsec.exe /fixmbr, /fixboot, and /rebuildBCD commands. Again, all have the same effect and I have to reinstall Grub to get anywhere.I don't have an installation disk to try and just do a repair install because Asus apparently doesn't feel that I would need one of these. All I have is the recovery disks from the Asus AIRecovery application that want to just re-format the entire drive and start over. This isn't an option. It's my GF's laptop (mine gave up the ghost last week) and we both have WAY too much highly important data on here. Not to mention she would castrate me . Now from all my research the only other thing I've come across that sounds possible is that the boot flag needs to be set to a different partition. Somebody had a somewhat similar problem and it turned out the way Dell set up the system the boot flag had to be moved to a recovery partition and it worked fine. I'm wondering if Asus has something similar going on, but I can't figure out how to move the boot flag. I'm going on 12 straight hours of working on this now
I would like to make my PC dual-boot with Windows 7 Home Premium 64bit version & Linux Ubuntu. I know about Wubi to install Ubuntu within Windows, But would like more space than the 30gb limit that Wubi uses. How do I create an partition with Windows that can be used for a dual-boot. doctorwhovian11-24144041650249291689021989539000 has chosen the best answer to his/her question. Click here to view the answer that was selected.
I have a dual boot scenario currently on an Intel 80GB SSD, with one partition as XP Pro, and the other is Windows 7, split 20GB(XP)/50GB(7).
The XP partition needs to be upgraded to Windows 7 for my wife's work remote access, and it will also include Office 2010 Pro.
Will I run into any issues dual booting into the existing Windows 7 partition after the upgrade, or should I just reinstall our personal Windows 7 OS after the upgrade is installed?
I have other hard drives to use as well if space becomes an issue, but I'd like to keep the existing Windows 7 install without starting from scratch.
I'm trying to install a new hard drive and retire my current one to backup and data storage purposes.
The problem is that I've installed Windows 7 on a hard drive with 2 partitions, an old XP partition (D:) and the new W7 partition (C:). At the moment the disk management screen looks like this:
What I am trying to do is delete the D: partition, and then copy/resize the C: partition including Windows 7 installation to my new hard drive (F:)
If I ignore the new hard drive and just try to migrate to a single partition, I can never get it to boot. I tried using Partition Wizard to set the C: as a primary, active partition, copied over the bootmgr and boot directory, then used bootrec /fixmbr and bootrec /fixboot to try to make Windows 7 bootable from just the C:, but it didn't work. All I got was "disk read error" whilst the PC was trying to boot off the C: (this is with all other drives disconnected...).
I could try to migrate to a single bootable partition from a 'dual boot' configuration?? I tried this video's advice and did everything as instructed but got the disk read error problem.
I have a laptop with twin HDDs and I have Vista on the C: partition on Drive 1. I created a new partition G: on Drive 2 and, while Vista was running, inserted the Win 7 disc and started installation to G:. All went perfectly and I have retained my original partitions with drive letters and labels, plus a new G: partition labeled Win 7. All seems to be working fine.Now I heard from a geeky friend that BOTH OS should be running on C: and that windows has some clever way of making that work. Is this true - and are there any disadvantages continuing installing MANY apps on G:?