Access Share On XP Box: Safe Mode Networking
Mar 23, 2008
I would like to transfer some files from my old XP laptop to my new Vista laptop. All available Windows updates have been applied to both boxes and both boxes are plugged into my Linksys BEFSX41 router. I must boot my XP box in "Safe Mode with Networking" because some unknown startup item has been causing problems. For both boxes, my logon account is a member of the local Administrators group and has a blank password. On my XP box, in Explorer I share the folder "xfer" which contains my files. I grant "Full Control" to "Everyone".
On my Vista box, in Explorer I can see my XP box, but when I double-click on it I get the message:"is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Logon failure: user account restrictions. Possible reasons are blank passwords not allowed, logon hour restrictions, or a policy restriction has been enforced."
View 6 Replies
ADVERTISEMENT
Aug 18, 2009
Is there a way to make 'Safe Mode with Networking' actually network?
View 5 Replies
View Related
Jul 10, 2009
I am writing now in ''safe mode with networking''.My ''Windows security alert'' program was disabled for some time, last night I had feeling, that my PC caught virus, so I better enabled WSA. When i tried that, I couldn't enable, it showed ''The Security center service can't be started'' and froze my Windows (I couldn't click anything, my keyboard was freezed and seems that it loads something all the time and never stops). So I restarted my PC and logged in same profile and it freezes again.Now I can only use PC in safe modes and my other Windows User profile.
View 4 Replies
View Related
Aug 30, 2009
my sony laptop ( vgn-fz70b ) shutdown with no reason, all of a sudden when i try to restart i saw a blue screen of death and afterwards it shutdown and restart again.i try to press f8 to open in safe mode and to check what is the problem but unfortunately i cant access to safemode.i try to reinstall again the os but when i am in the part that choosing the drive i didnt see any drive. and < click load driver to provide a mass storage driver for installation >.i stop downloading cause i cant see any harddisk on their.and i check bios setup..
boot priority order:
1:usb optical drive (*)
2:internal optical drive
3:floppy disk drive(*)
4:usb flash (*)
5:usb hard disk drive (*)
6:internal hard disk drive
7:network
there is no change values for all of these which supposed to be is to set them who is 1st,2nd,3rd. *-means this drive is available when external device boot is enable.
View 6 Replies
View Related
May 14, 2008
First of all I am not the most technically minded person when it comes to networking so whoever is able to help then please use child talk! All I want to do is get my Vista Home Premium laptop to share my XP desktop - and vice versa. How do I do it? I was easily able to do it on 2 XP machines but I am totally baffled by the XP to Vista set up :
View 4 Replies
View Related
Mar 23, 2008
Trying to network a Vista laptop with an xp desktop. Want to share files and printer on the xp machine. I have downloaded and installed LLTD as suggested by others. Still unable to see the xp machine on the Vista map. Vista is running Norton 360 and the XP is running Norton Antivirus, latest version
View 5 Replies
View Related
Oct 12, 2009
Using my ISP (Roadrunner Carolinas) speed test site; I get around 200 to 400 kbps download speeds using IE in normal mode. If I boot to Safe Mode, I get around 3500 to 4500 kbps, which is what it should be (this is what I used to get in normal mode before I re-installed Vista). Running the same speed test with Firefox, I get around 1500 to 2000 kbps in normal mode, but if I try to download a file it ransfers at only the 200 to 400 kbsp rate (if I'm lucky). Here's more detail about the system and what I've done so far:
Installed all updates including SP2.
Using Windows Firewall, no anti-virus.
Updated network drivers directly from NVidia (Chipset is nForce750i)
Updated graphics card drivers directly from NVidia
Disabled all LAN protocols except for Client for Microsoft Networks and IPv4
Connected via ethernet cable directly to cable modem, no router.
I've deliberately refrained from loading anything but the basics until I can get this sorted out..........
View 7 Replies
View Related
Mar 23, 2008
I've tried and tried, please I hope you can help me. I have a Toshiba A215-4817 laptop with Vista Home Premium 32bit. My troubles began when my cd/dvd was not operating properly. Toshiba support said my operating system was corrupt. I didn't believe that just because the cd/dvd wasn't working properly that the os is corrupt, maybe they were right.
I have extremely important info on my hd as I do taxes for a living.
In an effort to trouble shoot the cd/dvd I booted into safe mode. No-one tole me that the administrator account is disabled by default! So now I can't get out of safe mode. I have access to only my limited user account and uac is enabled. System restore doesn't change boot options.
I can't edit registry = access denied, cmd.exe when trying to activate administrator account = system error 5.
View 9 Replies
View Related
May 12, 2009
i'm on windows vista and i can't get out of safe mode does anyone know how to x
View 9 Replies
View Related
Jun 26, 2008
My son kept shutting the laptop w/o powering down and now it starts in safe mode. The first time I rebooted and this solved the problem but now that won't work. I can't get it to go back to normal. This has happened in the past but I can't remember what I did to fix it.
View 9 Replies
View Related
Mar 23, 2008
I had an issue with one of my games and it directed me to go into safe mode to uninstall it. Now that it's uninstalled, I can't get out of safe mode. I've been through this forum in and out. I've done nearly all the things that it has stated that come close to my issue. I'm still in here. I've been in and out for 3 hours now. I've gone through the msconfig, and told it to restart in normal mode, I'm still in safe mode. I've used the F8 button while starting it, and told it to go to safe mode, I'm still here. I've even checked to see if it was the resolution, I've set it to my default settings of 1280x720, and restart it, it's still in safe mode. I've done EVERYTHING that I can think of.
View 6 Replies
View Related
Apr 24, 2008
I press f5 or is it f8. but either way I get to the Safe Mood Selection screen and no matter what option I select, Safe Mode or Safe Mode with Prompts, of Safe Mood with Network support, it doesn't matter it boots normal to my user sign in screen and then it freezes.. no mouse or keyboard functions... If I run the recovery disk and tool options then mouse and keyboard work but I still cannot boot up in safe mode nor can I boot up normal.. I just need to get into safe mode and then I believe I can resolve this but since I can't get into safe mode I don't know what else to do?
View 9 Replies
View Related
Nov 14, 2009
I had trend doing a new scan a more complete one while it was doing it i went in i could stop it hit cancel stop safe box and computer wouldreturn to normal I thought that was 6 hourds ago well after i deletedtrend it still in a safe mode.
View 9 Replies
View Related
Nov 14, 2009
I can say is I changed trend to do a real good cleaning of all of folders etc. When I got the safe mode I found trend was doinmg a scan so I stopped it and then it said close and stop safe mode which I did. I also deleted trend to. I m really bad I dont know what I did. I use that I had brain surgery and I m just dah sometimes.
View 5 Replies
View Related
Mar 23, 2008
I have a new motherboard (abit nh-m2sv), X2 +3800 processor, 2 gig pc4200 memory ATI graphics, DVD RW, Maxtor SATA drive, all are suppose to be Vista ready, but vista either won't install, or installs with BSOD's then will only run in Safe Mode.
I have tried Home Basic and premium, the same issue, I install my old faitful XP and it goes straight in. I have run memtest, all fine, I have removed the gfx card, no change, I have tried an IDE hdd rather than a SATA no change.
View 6 Replies
View Related
Jan 19, 2010
Vista will not boot into Safe mode or Normally. The mouse pointer sits on the screen and can be moved but the logon screen does not appear. When I go into startup repair it says it "Could not detect a problem". I have run a chkdsk /f which ran clean. What else can I try to make the logon screen appear?
View 5 Replies
View Related
Sep 8, 2009
I?m have a troubling issue with my computer as it is stuck on a cycle boot when it passes the windows loading screen and then it simply restarts and does a POST test again. I tried pushing F8 key and selecting all the options
safe mode
safe mode with command prompt
safe mode with networking
Go to last working configuration (advanced)
Start Windows Normally ect....
but as I selected safe mode all the windows emergency drivers are loading then the screen go black and repeats the same problem above. I don?t have a cdrom neither an fdd only a usb flash drive.
View 8 Replies
View Related
Nov 3, 2009
I have a dell laptop with Vista factory installed. The other day is stopped booting and it can not repair itself. I am attempting to get into safe mode to check a few things out. However pressing or holding F8 while rebooting does not work for me. I have tried about 50 times. If I can not get windows to load are there any other ways through the command prompt or something to get windows to load in safe mode?
View 6 Replies
View Related
Oct 20, 2009
I find that my few graphics intensive games run much better in Safe Mode. Problem is there's no sound. Anyway to have Safe Node start with sound?
View 6 Replies
View Related
Oct 18, 2009
I am running Vista home Basic SP 2 and ( Emachine Desktop) Vista Home Premium SP 2 (Acer Laptop) when ever I come out from safe mode back to normal Windows it all ways opens with Windows Standard on both< is that normal? its no big deal to change it to vista Basic or Aero or anything else just curious is that the way it goes?
View 5 Replies
View Related
Nov 12, 2007
when I boot into safe mode, I am unable to do anything, install, open folders as nothing works, I have no error messages, just nothing works, if I take out 2 gigs leaving me with only 2 gigs everthing is just perfect I have tried installing the hotfix that I see on the forums "Windows6.0-KB929777-v2-x64.msu but it gives a error saying that its not for my machine I am running buiness edition Vista 64 Apart from this my machine runs just fine and for the last 6 months, only the safe mode gives me problems with the 4 gigs
View 5 Replies
View Related
Jun 12, 2009
I know you guys have heard again and again, "my computer will only boot in safemode, And yes I have seen it many times before but this is the first time I was never given a choice to the matter. When the computer boots it goes right for safemode even if I press "F8" select Boot computer normaly and it will still go into safemode.
View 8 Replies
View Related
Mar 23, 2008
Not sure what hapened, i'll summarise here:
1) Installed Vista Ultimate - all worked fine no issues - besides not bieng able to detect more thn 9 channels.
2) I removed my Kworld DBV-T driver after having restarted and it detected
the panasonic chiset driver.
3) Restarted again recieved 0x0000007e,
4) Safemode and i got 0x0000008e
5) Tried to restore last known good config i got STOP: C0000218 (registry file failure)
So now i cant get to safe mode - i cant try to put in Vista DVD & choose repair PC - as soon as i do, i recieve 0x0000008E
View 4 Replies
View Related
Mar 29, 2009
I have a computer I can only boot into safe mode. I recently rebuilt a cannabolized HP computer and I cannot boot the machine into windows. I have tried three different, working, hard drives on it, but have had no luck. One of the drives is the original to the machine and runs Vista Ultimate 32bit. Vista booted suceessfully prior to the cannabolization. The second hard drive runs XP Home and also boots into Safe Mode only. The third hard has no OS so I tried installing a commercial version of Vista which was unsuccessful. Computer would crash. I ran a few hardware tests and the memory, cpu, optical drive, and hard drive check out. I don't think anything is wrong with the motherboard as the computer worked fine before. The computer is stable in BIOS setup, and when booting to optical disc. No POST errors.
The hardware I added should be compatible with the motherboard (M2n68-Narra2) as I checked with HP website. The hardware I added: Antec 500watt power supply, DDR2 8Gb Ram, Sony DVD drive, Samsung 640Gb HD, Thermaltake CPU cooler, AMD X2 5600+ processor. I am out of ideas on how to make the computer boot into Windows
View 4 Replies
View Related
Dec 13, 2008
turns out that most likely the culprit for my computer acting different is because of Microsoft Office. The problem I have is with not being able to get microsoft updates, open control panel, etc. I went into safe mode and tried to uninstall, but it would not let me. So I cold deleted from the program files folder. However, now that I'm in regular mode, my computer is still acting like before. How do I resolve this?..
View 4 Replies
View Related
Sep 7, 2008
I am stuck in safe mode and can't get out.
View 4 Replies
View Related
May 31, 2008
every time my computer boots up in goes in safe mode...i tried restoring to earlier point...tried last know good configuration....tried repair computer...nothing is working.
View 4 Replies
View Related
May 4, 2008
I had tried to see if I could use one monitor for 2 computers and now I'm unable to get back to the way it was. In display settings they showed screen 1 and 2. I had asked to few screen 2 and that did it. There are no icons, nothing. Just background. No start either. I am however able to right click and get to the control panel, but some places will not respond like the one I need to get to. (Display settings) Safe mode won't even work. Can't even get to the registry.
View 4 Replies
View Related
Sep 10, 2009
I am using ASUS G51VX which I purchased last month. Since each time I wanted to install files which are over 1GB will become extremely slow. I decide to use the ASUS recovery disc to recover my Vista home premium. However, now each time after the loading screen, my PC will not process and enter the Window. I tried also with safe mode but it is not working.
View 4 Replies
View Related
Apr 19, 2009
I tried to install WINDOWS 7 THEME ( I know big mistake ) after changing these two files wscui.cpl wscntfy.dll in C:/ windows system32 I did change these to .old just incase there was a problem but they aint there now. So I have no controll pannel, and system restore isn't there either, I have tried in SAFE MODE aswell but this didn't work.
View 2 Replies
View Related
Dec 8, 2009
I have a file on my desktop called gv.com.gamesforwindows_640x360.mov. It was a video about gaming. It's 45.5 MB and I can't get it to delete. Right-clicking it and doing Properties doesn't open the Properties window. If I move it to the recycle bin (with the keyboard delete button or the mouse, or Shift and Delete) the "Calculation time remaining" delete dialogue comes up and the progress bar keeps on flashing, but it never deletes the file. The file does not seem to be in use by any programs. Renaming the file or its extension doesn't help. If I try to add the file to Kaspersky Anti-Virus' quarantine, even Kaspersky freezes in a not-responding state. Opening the file crashes the player. Using many force-deletion programs doesn't work either. I have even opened the file with Notepad and deleted the gibberish-text and tried to save it but that crashes Notepad! Safe Mode also doesn't work. Is there any other way to delete this file without attaching the drive to another computer and trying to delete it from there? If I boot with the Vista DVD and enter command prompt through it's Repair centre, what do I enter to delete it from there?
View 5 Replies
View Related