Setup Installation :: Space Requirements On Fresh Install?
Jan 30, 2013
I just purchased a neww 120 intel 520 ssd to load win 8 pro on and here is my question. I loaded win 7 and all updates then used the upgrade dvd I bought for win 8, I was under the impression from what I have read that it was only supposed to use about 20 gigs of the drive mine however is using 33.5 gigs of the 111 that the drive has? All that I can see that it has other than the os is it loaded the most current nvidis drivers for my graphics card but that should not be 13.5 gigs! What did I do wrong on this install and how can I fix it?
View 4 Replies
ADVERTISEMENT
Jul 8, 2013
So I've ordered a whole new system and am looking to only take the SSD from the old computer, but I want to format it so I can start anew, I've got windows 8 and I'm not sure how I go about activating it on the new system and all that.
I've got the key that I had to use for the first installation, would I just plug that in again? or will it come up with "being used" or something similar?
View 1 Replies
View Related
May 3, 2014
I bought a new HP x360. As expected it comes with a slow drive loaded to the gills with bloatware. So I planned from the beginning to install a fresh copy of 8.1 on a SSD.
I used a new SSD and without doing too much reading created a bootable usb from the 8.1 upgrade with key link. Unbeknownst to me is that the win 7 machine I used (where I previously created a usb key for win 8 pro) is also a pro install that retained the previous key. It never asked for a key when creating the usb. So I ended up with a pro install on the HP laptop and I could not enable the key associated with the laptop.
Thus I started over. I tried various things to create a non-pro usb and had a lot of problems and tried various things. I ultimately succeeded in creating a x64 core 8.1 usb. Now my challenge is that I cannot see the SSD anymore. Even in diskpart I cannot see the ssd. At some point while the ssd was still available (but my install usb did not work due to wrong key) I ran diskpart with the following:
clean
create partition primary
select partition 1
active
format fs=ntfs
assign
Since then I could not see the ssd. I have tried the following:
-Put original disk back in. Install Paragon. Clone install over to ssd. Put ssd back in laptop. "No bootable device found"
-Put ssd in win 7. Run diskpart. Clean All. Convert GPT.
It is possible the problem lies in the bois. The model laptop is brand new. I updated the bios (it was 2 versions old). But HP site had no explanation of what changed in bios. I also enabled legacy support.
BTW the only way I can create a bootable usb is with Zotac WinUSB maker. Even with win7 usb maker the drive is not recognized. With Zotac I can enable EFI. If I create the image without EFI the laptop does not see it (again even if legacy support is enabled).
So to summarize;
With official 8.1 upgrade image and fresh SSD I could install
After that with 8.1 iso and drive cleaned with diskpart I cannot see drive
I tried again with the upgrade win 8.1 with product key and it worked again. Then I again tried with the ISO. But it still will not recognize the ssd. I get "a media driver your computer needs is missing". A common problem for this is using usb3. I tried with usb 3 and 2. When I shift=f10 and list disk I do not see the ssd.
View 9 Replies
View Related
Jun 29, 2013
I decided to make a fresh install with a iso from the download page and use the key that they provide on that same page. Windows 8.1 Preview ISO files - Microsoft Windows. I tried english 64bit...
Running from windows 8 seamed to work but i didnt have 6.8 GB free .. So I go to boot from the iso and format the partition. But got the message saying , the key is invalid ... tried my own genuine windows 8 pro key .. also didn't work.
View 3 Replies
View Related
Mar 29, 2014
I am currently running Windows 8.1 and I want to do a clean install back to Windows 8. I have the original 64-bit Windows 8 Pro DVD. I put this DVD into my DVD drive and rebooted. I then went into the BIOS and made sure the first boot device was set to DVD/CDROM.
When I restart my computer it never gives me the option of booting to the DVD it just takes me back to the Operating System (my login screen).
My question is, how do I get my system to bootup from the Windows 8 Pro DVD so that I can do a fresh install?
View 7 Replies
View Related
Jul 19, 2013
Bought a Sony Vaio Pro 13 and as per usual with all my new laptops, a fresh install is done.
So on i went armed with my USB with Windows 8 created from an iso file from the microsoft site (i have msdn access).
The iso is a "multiple version" iso which has Windows 8 and Windows 8 Pro (en-gb_windows_8_x64_dvd_915412.iso)
Normally i would expect at the end of the install for the screen to allow me to enter my serial which in turn actives/deactivates features but for some reason, it has not this time round.
instead, the properties of my computer suggest a serial has already been entered "Current product key" *****-66ABC
Now i know i can "add features" and enter the serial that way but my question is, where is it picking the old serial from? i can only guess that the old serial is the one the laptop came with which is Windows 8 and not Windows 8 Pro.
The install was normal in terms of removing all partitions ( left the windows re and the sony recovery) so is it picking it up from there somehow?
View 4 Replies
View Related
May 20, 2014
I bought a new laptop with Windows 8 pre-installed (and immediately updated it to 8.1).
I decided after a week to buy an SSD and installed Windows 8.
I now find there is no product key to be found, and can't seem to activate Windows.
1. I've tried a few things. I tried to enable UEFI in PC Settings, but the setting isn't there (does this mean my laptop doesn't support UEFI?)
2. I entered my BIOS. CWM was enabled, and pwe enable. But SECURE BOOT disabled. So I enabled SECURE BOOT, but regardless of what options I select, the laptop keeps booting into the [Legacy] BIOS, possible because there are no BOOT OPTION PRIORITIES found any longer?
My problem is activating windows, and if UEFI is an option, enabling it.
View 9 Replies
View Related
Mar 7, 2013
I swapped the HDD with a new blank SSD in T530 and booted it with the recovery USB of windows 8. System boots from the USB and gives refresh, reset, and other options. However, when I select reset ( to fresh isntall the OS on the SSD), it fails saying a required partition is missing. What! I'm using a blank SSD, shouldn't the installer present me with options to format and use the drive rather than erring out?
Is there any better way of installing the windows 8 os on a new blank SSD using the recovery USB?
I do have gParted live USB. If nothing works, I will partition the SSD using gParted and try the Windows 8 recovery USB again.
View 3 Replies
View Related
Jan 5, 2013
I would like to try Windows 8 Pro on my PC, I've currently installed Windows 7 Ultimate (32-bit) with SP1 on my PC which takes about 7.8 gigs of disk space. So, my question is that how much disk space does a normal clean installation of Windows 8 Pro (32-bit) takes?
View 3 Replies
View Related
Mar 14, 2013
I installed Windows 8 Pro on a GPT partition. I have 234GB of SSD with 87% free space according to Disk Management. I am trying to create a 4GB primary partition for Intel Rapid Start but the Disk Part shows i have no space available in that drive and would not let me create the partition. Why would that be?
View 1 Replies
View Related
Aug 18, 2014
I partitioned my hard disk into a 150GB (C) and 500GB (D) and upgraded from Win7 to Windows 8 (and subsequently Windows 8.1 after the recent updates). The OS is installed onto the C Drive.
Performed a Clean Installation of Windows 8 on my C Drive. Under the Choose What To Keep Option, I selected Nothing.
Technically speaking my C Drive would have been wiped clean but after the Windows 8 installation, my C Drive only has 5GB of space left (145GB is being used). The Windows 8 OS is not detecting any of the old programs in my C Drive and the automated Disk Clean up feature only offers removal of temporary internet files. Which brings me to one possible assumption...
The Clean Installation Failed. Windows 8 simply installed itself again on my C Drive and the remaining disk space (containing my previous Windows 8.1 OS and programs) is locked down somewhere. I suspect this had something to do with changing my HD format 3 years ago when I wiped clean my pre-loaded ASUS laptop Win7 and partitioned it to install my Windows 8.
How to remove my previous OS?
View 2 Replies
View Related
Jun 18, 2013
I just bought a 1TB hard drive and want to install windows 8 on it (since I'm used to it already) I have the files for windows 8 on my computer ready to be put on the new hard drive, but thing is, how would I do it? would I just use a simple USB stick and plug it in? or would i have to burn the files on a disk?
Amazon.com: WD Blue 1 TB Desktop Hard Drive: 3.5 Inch, 7200 RPM, SATA 6 Gb/s, 64 MB Cache - WD10EZEX: Computers & Accessories.
View 3 Replies
View Related
Feb 23, 2014
I have a 256gb ssd installed on my laptop and I recently had installed Ubuntu partition on it and ended up removing it. I have instead reinstalled a fresh copy of Windows 8. However I see no other partition during the installation processing and it's saying I only have 238gb available not my disk's full 256gb. So far I tried chkdsk and disk management and it failed to see any other used space.
View 9 Replies
View Related
Apr 24, 2014
I just found out that some of space in one of my partition is occupied by NO file after I updated my Windows 8 to Windows 8.1 via MS Store. There is no file hidden in the partition but the computer shows me that 3GB of a partition in my second hard drive are being used.
What I did on my computer before I updated Windows 8 were:
1. Recovered my PC to the factory state
2. Formatted all partitions in both hard drives (the primary one has 3 partitions, not including those Windows hidden partitions, and the second one has 4 partitions).
3. Updated my Windows 8
4. Went through the setup screens
Then I found that 3GB of a partition in the second drive is being used, but there is no file or hidden file there. Do you know what behind this usage???
View 6 Replies
View Related
Jun 28, 2013
put Windows 8 recovery on a 1TB ext HDD; Decided after to put on smaller HDD & copied to it. Now my 1TB ext HDD reads empty but only 31.9GO! Tried format & Seatools, which says everything ok. How to get my HDD to full capacity again?
I would also like to delete the recovery from the main HDD & save space. I was given this option at the time but can't find it now?
View 9 Replies
View Related
Nov 6, 2012
OK, long story short. I did a clean install to Windows 8 Pro 64. Because of the System Reserved partition, it showed both Win 7 and Win 8 available and would prompt to do a dual boot. I cleaned it up by following the instructions on the below link.
Dual Boot - Delete a OS - Windows 7 Forums
It now no longer dual boots, and Windows 8 is fine. The only issue remaining is that my primary drive in drive management still has unallocated space. Disk 0 has 351MB Unallocated space, and 465GB of system boot, page file, etc...
In the instructions, it says to "Right click on the partition that contains the OS you want to delete and Delete Volume. Then right click on the deleted volume and Delete Partition. Now you should have "Freespace" where this partition originally was."
Well, I can't do that. When I right-click on the unallocated space, all I can do is: New Simple Volume, Properties. Everything else is greyed out. I also can't extend the other partition, the "extend" option is also greyed out.
I'm now on Win 8... How to put that 351MB onto the main partition?
View 6 Replies
View Related
Dec 26, 2013
I'm trying to upgrade from Windows 7 to Windows 8 (and then 8.1) on a laptop with a 240 GB SSD. When I run setup, it loads, but then says Windows can't be installed because there isn't enough free space on the system reserved partition. My reserved partition is only 32 MB (I believe it was shrunk from 100 MB when I swapped the SSD in).
Is there any way I can resize the reserved partition and install Windows 8, or will I need to totally reformat the drive and repartition? Don't want to reinstall all my software .....
View 8 Replies
View Related
Jan 20, 2013
I just got a new laptop, a Lenovo X230, for which I paid extra to have the OS on it as Windows 8 Pro.
So--now I have it, and Win 8 Pro 64 is installed and activated on it. I am a legal owner of Win 8 Pro.
However, I would like to do a clean install of Win 8 on the computer, to have it free of bloatware, etc. (In fact, I would like to set up a multi-boot with Win 7, and perhaps even triple boot with Xp as well. (I have installation media and my product keys for XP and 7 though, so those are not really a problem.)
The computer came with no discs at all. There is a procedure to make recovery disks. I may do that, but I think those will be to restore the computer to how it came from the factory, and therefore not usable for a clean install.
I don't see my product key for Win 8 anywhere. Not on the computer, not on any kind of card that came with it, etc.
I looked at the tutorial here for clean install of Windows 8, but it requires an install disc and product key. I have neither, although I am a legal owner of Windows 8.
Is there a way I can create (from my installed Windows 8) a win 8 install disk, that can be used for a clean install? Or a link to download one? Is there a way I can get my product key?
View 9 Replies
View Related
Sep 15, 2014
I recently installed Windows 8.1 Pro x64 and the correct up to date drivers for my hardware. I experience a BSOD, it doesn't go into the BSOD right away but after 15-30 minutes of use I get the BSOD with the "page fault in nonpaged area" message.
I have attached my debugfiles and hope that someone much brighter than me in deciphering these files can lend me a hand at fixing this issue.
Found out it was my new Panda Cloud Free Antivirus. I deleted the POS and installed something else, now no more BSODs.
View 3 Replies
View Related
Nov 1, 2012
I tried using this method:
-After installation disconect from internet
-change in registry: HKEY_LOCAL_MACHINE/Software/Microsoft/Windows/CurrentVersion/Setup/OOBE -> Change "MediaBootInstall" from "1" to "0"
-type "slmgr /rearm" into a command prompt, waited for confirmation, restart
-after restart, connect to internet, activate
This works fine until rebooting and then asks for activation again.
I have tried three more times without reinstalling and the MediaBootInstall stays at 0 so it doesn't need changing. I type the slmgr /rearm and on reboot when I go to activation menu it says activated, but when I reboot agian it says needs activation.
Not sure what's going on. I thought it was a windows update at first messing with it, but it still does it even without any updates being installed.
View 9 Replies
View Related
Oct 11, 2013
I just got three 320GB Seagate drives setup in RAID 0 for Linux, and I decided to also reinstall Windows 8 on my SSD since it started lagging and running slower than normal. While trying to install Windows 8, right after selecting a disk/partition to install to, I got a BSOD about an error in a nonpaged area or something. When I tried to boot into the installer again, I got a BSOD immediately after the logo splashscreen (too quick to see what it was about).
-I'm booting the Windows 8 installer from a Corsair Survivor 64GB USB3.0 flashdrive. I'm gonna try a dvd with a different iso that I downloaded more recently on my laptop.
View 1 Replies
View Related
May 7, 2014
I built a computer about a year ago and its run fine until about a month ago when my displays started shutting off and not coming back on. The only way I could get my displays to come back on would be to disconnect both monitors and only plug in the monitor that connects with DVI. Connecting the second monitor would cause both to cut out and sometimes BSOD. It seems the same thing was happening with the on-board video. I finally decided to do a fresh Windows 8.1 install and see if the problem persisted. As soon as the I got up and running again I got a BSOD (before installing any drivers). I then did the following tests.
- Ran memtest for 2 passes (no errors)
- Tried my GPU on a different PCI-E slot (Still BSOD)
- Tried unplugging the power from the GPU (Still connected to the PCI-E slot, still BSOD)
I was thinking of trying with the video card out completely but it seems the crash is random and I can't reproduce it.
View 9 Replies
View Related
Nov 17, 2013
I have MSI laptop GT70-20D all my drivers are updated to work with windows 8.1 from offical MSI site & I have my laptop running smooth once I leave it on for downloading my windows BSOD ...
View 1 Replies
View Related
Sep 15, 2014
My system currently has a blue screen around twice a day from what seems like a driver issue. I have tried driver verifier, swapped out the GPU since I thought most things pointed to that and did a fresh install. The only thing I have left to do is update my motherboard bios. I am questioning if the GPU was even the issue since I still got a crash... Below is the guide to Driver Verifier I used so you can see what steps I took. I am at my wits end and am not to great at pointing out what driver crashed or whats left to do after the OS install.
Driver Verifier-- tracking down a mis-behaving driver.
View 9 Replies
View Related
Jul 3, 2014
So I was getting bsods before and had my HDD wiped. when attempting to install windows 8 I get a bsod. Not sure which as it is too quick to read. I have flashed the bios to the most recent version. But it still bsods. I tried using a known, good working HDD with windows installed and it still caused a bsod.
View 1 Replies
View Related
Mar 27, 2014
Just got in the mail 2 ssd's and the HD7870 video card along with a copy of windows 8.1 complete (retail). My boot ssd (one I'm trying to install on) is a 60gb Mushkin and the other is the one I was going to put games on the 240gb Mushkin.
So I hooked the 60gb one up and put in my install disk for the 64bit of windows 8.1. It went through the install fine, then it said it needed to restart to complete and when it restarted it gave me the black screen of death. It sat there for over 30 minutes then the screen turned to a yellowish orange.
So I formatted the ssd, reinstalled fresh again. Same thing.
I then tried the 240gb thinking maybe I had a bad ssd. Same thing.
Then I tried an old 500gb Seagate that I knew worked but I formatted it and installed. Same thing.
So back to the 60gb I went, formatted, reinstalled 8.1 then it did the black screen again. So I tried booting over a couple times till it gave me the option to start in safe mode with networking. It started in a black screen with the blue windows logo... and stayed there for an hour.
I then tried the command prompt methods of BOOTREC/FIXMBR, BOOTREC/FIXBOOT, BOOTREC/REBUILDBCD and restarted with same black screen. *after the rebuildbcd, it said copies of windows = 0???*
So I tried to start using the install CD as a recovery drive, it brought up the option to install windows....
I'm not sure how I can get dumps or test stuff if there is no way for me to even get to the actual explorer other than the black screen or the black screen with the blue window logo, or even he more rare black screen with underscore blinking...
View 9 Replies
View Related
Mar 9, 2014
Just reinstalled windows 8 on my desktop and started to receive random bsod. I know windows 8.1 is out. I downgraded due to BSOD issues on that version also. Yes I also know my windows 8 is out dated. I understand I should update but that's the least of my concerns right now. I already had 1 ram card fail on me a couple months back. But I didn't recognize this blue screen error.
I was reading this guys post BSOD Critical Process Died even after complete reinstall and his issue is exactly like I am having. My computer would just completely freeze while playing games or watching videos online.
I Just tried to run Memtest86+ and something strange happened. So here's what I did. First I download the Memtest86+ USB Installer. Turned off my computer and put my other 2 rams cards back in (I was testing one at a time). Started up my computer (HP) and press ESC to go into the boot menu and the computer just froze on that screen. It wouldn't do anything. So I turned the computer off and tried another option F10 I think it was. The computer froze again. I repeated this process for all boot options on my PC and each time the computer froze on the startup screen.
View 7 Replies
View Related
Jun 6, 2014
I have a fresh install of Windows 8.1. Everything has been brought up to date including all hardware drivers and bios. I continue to experience the same BSOD every couple of days or so (Attached in this post). This is what else ive tried: Ive unplugged all extra hardware and it still continues to happen. Ive installed a different drive, tested memory (memtest) for 24 hours. Checked the power supply. Ran PC check on the mobo. etc. still continues to happen.
A problem has been detected and Windows has been shut down to prevent damage to your computer.
The problem seems to be caused by the following file: ntoskrnl.exe
If this is the first time you've seen this stop error screen,restart your computer. If this screen appears again, follow these steps:
Check to make sure any new hardware or software is properly installed.If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing.If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical Information:
*** STOP: 0x00000139 (0x0000000000000003, 0xffffd0002044cee0, 0xffffd0002044ce38,
0x0000000000000000)
*** ntoskrnl.exe - Address 0xfffff80091157fa0 base at 0xfffff80091004000 DateStamp
0x5318053f
View 5 Replies
View Related
Jul 12, 2014
I recently upgraded to an SSD, installing a fresh copy of Win8Pro.
I'm receiving constant BSODs, typically reporting BAD_POOL_HEADER and IRQL_NOT_LESS_OR_EQUAL
I've updated every driver I can think of (chipset, lan, usb, audio, video) as well as fully updating in windows update.
Memtest ran overnight finding no errors, and Western Digital's HDD utility reports no hard disk corruption.
I'm thinking either a bad driver, or some hardware failure that I can't nail down. My specs should be listed in my profile, with the addition of a 750w corsair PS and my HDD setup (AHCI, 1 crucial mx100 256gb SSD (primary), 1tb WD blue, and 1tb WD green as data drives).
Crash dumps should be attached, one may have driver verifier enabled.
Also, clean booting seems to be slightly more stable than a regular boot, so there's that.
Attempting to install windows 8.1 fails right at the end (after installing and setting up, reporting 0xC1900101 - 0x2003).
View 3 Replies
View Related
Jul 1, 2014
My computer keeps blue screening lately after a fresh install.
SF_01-07-2014.zip
View 1 Replies
View Related
Nov 16, 2012
A week ago I did a completely fresh install of Windows 8 64 bit and everything was working great. When I booted up my laptop on Wednesday I noticed it was running terribly slow. When I opened task manager I saw that disk usage was at 100% despite the combined total of data transfer being 0.8MB/s.
The problem occurs constantly if I set my laptop power mode to balanced but only occurs intermittently at high performance. I've run a chkdsk and everything is showing up fine and bizarrely there is no slowdown whatsoever on safe mode.
View 9 Replies
View Related
