Getting STOP 0x0000007B When Starting Windows 7
Dec 15, 2012
Recently, I've been getting a lot of BSODs and I've been trying to find what may cause them. I used the Device Manager and disabled a couple of devices. I've probably disabled a necessary device, and now when I'm booting my PC, it's getting to the point when it shows the Windows 7 logo, and then restarts, and so it gets into an endless restart loop.I then pressed F8 to try get into Safe Mode, but Safe Mode is not working as well. So I then pressed F8 when starting Windows again and chose "Disable automatic restart on system failure" to see what error code is being thrown. It shows the following: Code: *** STOP: 0x0000007B (...) Unfortunately I don't think I can get dump file because Windows is not working at all, but I have a very good assumption that I disabled a critical device in the Device Manager. Here is the list of devices that I've disabled: Code: Acronis Backup Archive Explorer Floppy disk drive (don't have any floppy disk drive)Standard floppy disk controller (same thing as above)High Definition Audio Device PCI bus (*I think the problem is here and is related to the on-board graphics card. I think It's an Intel graphics or something like this.) My question is: is there any way to somehow enable this PCI bus device from anywhere?
View 4 Replies
ADVERTISEMENT
May 4, 2012
I have a dell Inspiron n4010 it had Trojan viruses on it so I did an reinstall from the recovery partition now windows 7 will not boot I get a flash of the blue screen of death with a stop error 0x0000007b I can't get in to windows to check anything. I no longer have the dell disks that came with the comp. I have tried to reinstall from the partition 3 times and no luck
View 6 Replies
View Related
Mar 11, 2012
The blue screen A problem has been detected and windows has been shut down to prevent damage to your computer I also get this messege when I try other options:
Problem signature:
Problem Event name : StartupRepairOffline
Problem Signature 01: 6.1.7600.16385
Problem Signature 02: 6.1.7600.16385
Problem Signature 03: unknown
Problem Signature 04: 21201006
Problem Signature 05: AutoFailover
Problem Signature 06: 10
Problem Signature 07: NoRootCause
POS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
I have Windows 7 Home, 64bit, 4 G of RAM, GTX 285, Intel Core 2 Quad I had recently installed trial version of Kapersky . I had an earlier message after trying to restart and a black screen with the message bad image sector or something like that. It started several times before. Now it will not start and I had to disable the automatic startup and I got the above messege. I cannot do the system restore because it just won't and I hear Kapersky sometimes prevents this. No detecable disk errors have been noted but it still will not even boot into safe mode. This process just keeps repeating and nothing seems to be helping. I had this message before when my screen flickered before but the computer kept running. It has restarted automatically before also but with no problems. My system will also, not restore to another check point. I am ready to reinstall windows.
View 4 Replies
View Related
Mar 23, 2012
I needed to reinstall windows on my laptop, but I had to recover some files from the hard drive, so I took the hard drive out and connected it to my desktop PC. I installed the windows on the hard drive using my desktop PC too, because the laptops DVD ROM doesn't work anymore. I successfully installed windows on it, everything worked. I put the hard drive back in the laptop, booted the laptop and it popped up a BSOD saying:Check for viruses on your computer. Remove any newly installed hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK/F to check for hard drive corruption, and then restart your computer.Technical information:***STOP 0x00000073(OXFC8D3640), 0xC0000034, 0x00000000, 0x00000000
View 3 Replies
View Related
Nov 18, 2012
I have a decent PC (i7 2600, 16gb ram, SSD + 2HDDs, etc). I've been using it for about a year.Since it's a work machine, in the last few weeks, I've been using VMware on it to use other experimental software, with no problems.Today, I tried to create a new VM and the software asked me to update it to a new version. I did it, create new VM and rebooted to change a config in the Bios (about virtualization). But when I tried to boot again, surprise: BSOD.
STOP: 0x0000007b, (0xFFFFF880009a9928, 0xFFFFFFFFC0000034, 0x0000000000000000, 0x0000000000000000)
When I got back to the BIOS, I found the boot order to be different. I fixed it but no good. I disconnected the other HDDs and all I got was a different boot error message. I plugged the SSD in another machine and it worked fine?
View 13 Replies
View Related
Nov 16, 2011
Is there a way to stop selected applications or services from starting up with Windows? Is there a list of such items that can be safely disabled?
View 3 Replies
View Related
Dec 1, 2012
My girlfriend is having this problem where heroutlook 2010 is starting up when she starts windows, she dosent want that
I have checked the msconfig, but no outlook in there !
View 2 Replies
View Related
Sep 24, 2011
How can I stop the wrong operating system from starting?, downloading the software from softpedia. When I opened it, there was immediately an option to alter the startup settings so I deleted vista and set windows 7 to default. Now, when I turn on thhe put, it automatically tries and fails to start vista, with no option to start 7 (meaning I can't use my computer). I've scoured the bios for something to do but can't find anything. Also, I've tried putting in the disc I used to install with, but the same messages come up, even when I say boot from CD and not the HDD!
View 2 Replies
View Related
Nov 30, 2011
I cloned a hard drive that had an image all set up with all kinds of programs and settings. Now that I put that cloned hard drive in a new computer (any) even the same exact harddware of an older computer, it gets BSOD and auto restarts. Tried startup recovery and no fixes found or worked.
View 3 Replies
View Related
Aug 1, 2012
when ever any .exe is run it dumps a 0x0000007b memory error. I've replaced the .DLL for exes off the top of my head think it was summert like msi.DLL and still no good also ran Norton antivirus and although items were removed still no good did regserv32 with the .dll's and no result still same memory reference this is on a laptop running 64 bit home premium
View 2 Replies
View Related
May 1, 2012
so yesterday I decided to upgrade my computer with a new motherboard/cpu.But I wanted to keep the old hard drive since I have all my files there, and everything was going smoothly until I actually tried to boot it.When I boot Windows 7 it gives me this bluescreen error: Code: STOP 0x0000007B (0xFFFFF880009A9928, 0xFFFFFFFFC0000034, 0x0000000000000000, 0x0000000000000000) I have tried to reinstall windows on another clean hard drive, but doesn't want to boot that either.
Specs:
Power supply: The one I had in my old HP Pavillion, 460w
Motherboard: Asus M4A88T-V EVO
CPU: AMD Phenom II X4 965 BE
Hard drive: Seagate Barracuda 200GB 7200 ST3200822AS
Graphics Card: EVGA GTX 460 1gb
Windows 7 Ultimate x64 full retail The hardware is from 2010 or so.The age of the os installation is 2011.
View 9 Replies
View Related
Jul 26, 2012
Had to perform Reinstall, reinstall completed when Restarting after reinstall, it will not boot, it gives me Microsoft loading bar then BOOM cuts rightout.. I attempted another reinstall same thing.. So I disabled automatic restart and this is the exact error: BSOD: 0x0000007b (0x80786B58, 0xC0000034, 0x00000000, 0x00000000) I saw in another forum possible registry adjustment could cure it however, it would require for me to take SSD out, which I really would like to avoid if possible, not an easy job for me with this smaller netbook.... I also tried changing SATA Drive from AHCI to ATA, and vice versa, no luck.. Stuck.
View 14 Replies
View Related
Oct 29, 2011
PC don't showing bios display on starting & start showing display after starting window
View 1 Replies
View Related
Sep 22, 2012
Having an issue with windows 7. I few days I ago it starting just randomly rebooting. Then on reboots it started going to a black screen.I ran my dell diognoatics and it says all the hard ware is ok. Popped in my win 7 disk and ran my startup repair.Now windows 7 is loading, but now of the desktop icons responds. If I hover the arrow over the windows icon in the lower left corner of the screen, I just get the spinning blue icon? Nothing responds.Can I reinstalling wimdows without it deleting my c drive? Running win 7 home n a dell xps 8300.
View 2 Replies
View Related
Jan 21, 2013
I recently installed poweriso and magicdisc on my computer then I rebooted but windows started to hang at shutdown so I just forced a shutdown, now windows is hanging up upon restart and the same happens for safe mode. I'm thinking the problem might be magicdisc cause it said drivers were not found and safe mode was hanging around the loading drivers part or that I made a virtual drive.
Also I'm attempting to do a system repair via windows disc
Edit: Windows repair just finished and the problem signature was
Problem event name: startuprepairoffline
Problem signature 01: 6.1.7600.16385
Problem signature 02: 6.1.7600.16385
Problem signature 03: unknown
[Code]....
View 1 Replies
View Related
Feb 23, 2012
i have a problem with its starting,it has been installed properly and works perfect when there is windows cd in its cd rom,otherwise it does not start and says operating system not found.
View 3 Replies
View Related
Feb 26, 2012
I have a laptop and I cannot get it to start. When I go into start-up mode (Esc key at start-up) I have two options:
Start-up Repair (Recommend)
Normal Start-up
When I do Normal Start-up, it lockes up on the Windows Screen. When I do Start-up Repair it locks up on a black screen.I don't have the back-up discs that were created for this specific computer at the moment (they are at another location at the moment). However I do have Windows 7 upgrade discs here from another computer.
View 2 Replies
View Related
Aug 4, 2011
It started with me interrupting a startup forcefully (which I now regret badly), then "i restarted it, but it gave me the information;"Windows failed to start. A recent hardware or software change might be the cause". I was given the option to either 'Launch startup repair' or 'Start windows normally'...If I select 'Launch startup repair', it leads me to a blank screen with a cursor then stays there until forever, if i select 'Start windows normally', it leads me to the Microsoft logo/'Starting windows' and just stays there for a while until it restarts." However, after the microsoft logo, I can see the screen changing for a split second, I can't see what it shows clearly a blue screen?
View 5 Replies
View Related
Jul 20, 2011
I have windows 7 already installed on my pc but i also want to install xp and for xp i went to bios and turn ahci to native ide but when i try open windows 7 in ide the windows is not booting then i launched startup repair no use is there any way to work windows 7 on ide without reinstalling it on ide ?
View 2 Replies
View Related
Jan 8, 2010
I installed Windows 7 (x64)/(x86) on my PC a while back without any problems at all. Now lately, when I start the computer up for the first time, it just wont start. Turn my monitor on and it says "No signal". I can only get the computer to boot up when i do several restart button pushes,So I figured it might be the video card drivers that are problematic and I installed the newest ones that I found from the official site(my graphics card is an XFX 9800GT). It didn't help, maybe relieved the problem a bit but I haven't really noticed it. I've opened the computer case up and tryed to push the Graphics card into the PCi slot further,is this a hardware or a software problem? :S I tryed searching for fixes for this but I got bored of searching too fast so I made this thread I'd like to get a quick fix, it's taking me 5-15 minutes to start up the computer every time, it's bad when I might be in a hurry someday
View 5 Replies
View Related
Aug 23, 2012
Every time I start my computer it scans the hard drive before starting and takes 10-20 minutes, this has happened since it crashed yesterday, I think it is a problem with missing files.
How do I fix the files that cause the problem and cause it to need to do a scan?
I have scanned using the scan before startup and the windows scan (the one that requires restart)
View 14 Replies
View Related
Jan 16, 2012
if I try to boot it normally it gets blue screen and dies. The same thing happends if I use fail safe. (crashed at crcdisk)So I thought idd reinstall it. However when i boot up from my windows cd, I only get the 2 possibilities to "setup and recovery". No matter which of those I choose it goes to "loading files" and then to "starting windows".I've reinstalled quite a few computers, with xp and windows 7, and I've never had any trouble doing so. So i thought idd try to take out the hdd manually, but I realised I dont have the cables to connect it to my other pc, and clean the hdd that way.
View 1 Replies
View Related
Mar 10, 2012
When I start Windows 7 64 I get 3 boot options. Windows 72. Windows 7 (recovered)3.Windown 7 (recovered)The first 2 are both dead and I would like to know how to make them go away. I used the start up disk it shows all 3 options but the first 2 it says that there is 0kb in both files and that only the 3rd oprion has any info in it
View 2 Replies
View Related
Nov 30, 2011
I have trouble when starting my computer. it starts after two or three craches before the logo of windows appears... I checkd, cleaned, and defragmented the disk.. it looks ok..
View 1 Replies
View Related
Sep 9, 2011
The power in southern california today and when it came back on my computer wouldnt boot all the way to windows. I have tried booting fromt he cd but it does the same thing and just stays at the splash screen. I have tried recovery mode and it sticks at the windows is loading files bar. Safe mode doesnt work either as it sticks at one file and stays there the entire time.
View 9 Replies
View Related
Apr 17, 2012
yesterday i turned on my PC and black screen appeared saying that windows couldn't find "windows/system" folder. then I installed Windows XP, first it worked fine but today the black screen appeared again saying the same. I have no idea what's wrong with it.
View 5 Replies
View Related
Apr 17, 2012
I had just put this build together and occasionally when I boot up the computer, it would freeze at "Starting Windows" screen and will not go anywhere else until I hard shutdown the computer and boot it back up and hope it doesn't get stuck again.I reinstalled Windows 7 thinking it's the new SSD I bought but the problem still occurs, I also ran CHKDSK again and no errors have shown up.I haven't ran a memory test program yet to check my RAM but I don't think that is the issue since I do not get BSOD of any kind.I also have another problem that rarely occurs and only happens when watching you tube videos, the screen completely friezes and artifacts show up as if the video card is broken but I never have such problems while playing video games such as BF3 and Starcraft II.Anyhow, I have searched Tomshardware and the web but still cannot find a solution to this and I hope you guys can help me find what the problem is.I'm beginning to question my RAM, Motherboard, or SSD at this moment.
View 7 Replies
View Related
Mar 20, 2010
When I boot up Windows 7 it gets to the "Starting Windows" screen which includes the Windows Logo with some animation. Once there it just hangs for about 5 minutes, then starts normally.I have Home Premium, 64 Bit, Dell XPS, Intel i7, 6BG of memory. I have several peripherals connected directly to it: Display, USB External Drive, Webcam, Bluetooth adapter.I tested booting in Safe Mode and it was very fast with no delay.I don't restart Windows 7 often so not 100% sure of when this really began. After the install booting up was very very fast. So this happened over the last month or so.The only hardware item I would mention is a Realtek card/usb reader which is built in to my unit as part of it. After Win 7 install it did not work at all and it took quite a while including working with Dell to finally track down the appropriate drivers. Now the unit works fine but I believe the problem began around that incident.Prior to uninstall or disabling the item I just wanted to check and see if this problem has been seen and make sure I am not going to do something to simply create a new problem. Also, since it was so difficult to finally get this Card Reader up and running I am concerned about just uninstalling it.
View 9 Replies
View Related
Jan 12, 2012
I've got a: Presario CQ62 notebook pc with a AMD Athlon(tm) II P320 Dual Core processor, and I can't get past the start up screen with the "starting windows" animation. It will show part of the animation then simply hang. I have a very bad battery but am keeping the computer plugged in. When I attempt a system recovery it says: "A disk read error occurred press ctrl+alt+del to restart" I've tried this many times and I get the same message each time. Beyond that I have no idea what to try.
View 2 Replies
View Related
Apr 16, 2011
my Windows 7 is not starting up on my HP Pavilion dv7-3160us. I tried startup repair, and this is the message i received:''startup repair cannot repair this computer automatically" problem evemt name: startup repair offline.Problem signature01and02:6.1.7600.16385 problem signatre 03: unknown. 04: 344.05: autofailover. 06: 1. 07: bad disk.
View 2 Replies
View Related
May 12, 2011
Everytime I start up i get this annoying screen:
1. How do I removed this from my startup
I have set my msconfig right:
and i also did disable here:
What the **** is wrong!
View 9 Replies
View Related
