Setup Installation :: Windows 8 Pro - UFEI BIOS / Cloning Disk

Jan 25, 2013

I am running windows 8 pro in a Intel i5 3470 + Gigabyte B75M-D3H system with UEFI bios .

I have two drives OS drive is a SSD & a 1 tb HDD with two partitions.

I am removing the SSD & want to transfer OS to one of the partitions on the HDD , the issue is boot files on the small 350mb system reserved partition on the OS drive , not sure how to transfer this partition or if this partion in on the SSD or the HDD.

This what my drives look like , C: is SSD :

Before i installed the SSD , I was running win 7 from the HDD installed in the 170 gb partition , to install the SSD i had to remove the HDD then do a fresh install of win 8 on the SSD & connected the HDD back later ,

The 170gb HDD partition is still untouched & has the old OS files , I want to transfer the SSD partition back to this 170gb partition i.e drive F: in the above pic . I am not sure how to transfer it & what to do with the system reserved partition .

View 3 Replies


ADVERTISEMENT

Setup Installation :: SSD Not Registered On Boot After HDD To SSD Cloning

Feb 17, 2014

I recently purchased an SSD to upgrade my Dell Inspiron 17R SE 7720 that runs Windows 8. This is the SSD I purchased and it came with cloning software: Amazon.com: Samsung Electronics 840 EVO-Series 250GB 2.5-Inch SATA III Single Unit Version Internal Solid State Drive MZ-7TE250BW: Computers & Accessories

I placed it in an external enclosure and cloned my HDD to the SSD using the program. After the cloning procedure the disk management looks like the figure below.

To me this looks good. But when I replace the internal HDD with the SSD it does not boot from the SSD at all. It takes me to the boot options and I don't see the SSD listed anywhere. I may just not be used to the Windows 8 setup.

View 9 Replies View Related

Setup Installation :: Migrating / Cloning GPT Secure Boot HDD To SDD

Jan 15, 2014

i have a Lenovo Ideapad Z585 running Windows 8, secure boot, gpt paritioning and UEFI bios.The laptop comes with a factory shipped 1TB Sata drive which i want to replace with a Kingston V300 SDD 120GB drive.

I have followed this guide How to Migrate OS to new Hard disk.Ive run this in another desktop, it completes and i shut down, remove the destination and insert it into the laptop - power up and it blue screens with There has been an unexpected error message. Trying to access the recovery partition says it is damaged but looks like its almost going to load. Looking at the drive in EaseUS paritition master the paritions look a perfect copy apart from the proportional sizing.

AHCI is enabled in bios - i've tried EaseUS Backup clone, task was successfull but again blue screens but this time with a attached device cant be found.

One thing i wasnt sure about, the PC i done the cloning in has a RAID stripe setup but not sure if this effects it.Any one had success in cloning a GPT drive over to a SSD?

I cant do a fresh installation of windows 8 as i dont have recovery discs, nor does the onekey recovery software allow me to do so and id like to keep the recovery parition in tact really.

View 7 Replies View Related

Setup Installation :: Cloned Win7 Drive Onto UEFI Win8 PC 7D BSOD After Cloning

Jan 9, 2014

have Acronis 2013 Plus. What I am trying to do is image the disk of a Windows 7 machine (source) to a machine that had Windows 8 pre-installed (target - Gateway SX2110G).

I connected the Windows 7 drive to the new machine (USB data cable), disabled Secure Boot, and enabled Legacy. Booted to True Image and started the cloning of the drive. Everything seemed to go ok, but as soon as it starts to boot Windows 7, it gives a 7D BSOD. (the same BSOD it gives when I simply plug the source hard drive into the target and try to boot from it).

The source HDD (win 7) boots fine in its original machine.

*I tried the startup repair that's included with the image.. does it matter if I use the one from a disc instead?

View 7 Replies View Related

Setup Installation :: Installing Windows 8 In BIOS Without CSM Launch

Sep 15, 2014

My problem is that I want to install a higher version of win 8, respectivily win 8 pro in a computer that already came with another version of win preinstalled (win 8.1). It's possible to do this in a bios that prevents csm launch.

View 1 Replies View Related

Setup Installation :: Migrating Windows 7 And 8 From BIOS To UEFI Computer

Jun 13, 2013

Question: How would you approach this migration?

I just bought a copy of Acronis True Image 2013 with Plus Pack. It appears that this is all I need as True Image will install the new motherboard drivers as part of the migration process. But do I stay with MBR or move to GPT?

Presently both Win7 (on a 120GB SSD drive) and Windows 8 (on a different 120GB SSD drive) are both MBR format. I don't want to start over from scratch. That's why I bought the Acronis 2013 with Plus Pack.

View 5 Replies View Related

Setup Installation :: Installing Windows 8 / 8.1 On External HDD UEFI Bios Only

Jul 21, 2014

I'm trying to install windows 8.1 to an external hard disk (solid state drive 128 gb usb3).

I've tried easyUFEY WinToUS creator and AOMEI Partition Assistant Standard(Windows to go) with no luck.

My bios has UEFI option only(no legacy). On my old laptop it works just fine(I had the legacy option) but now, I cannot do that anymore.

I'm pretty sure it's a bios boot issue and I don't know how to fix it. I've tried using GPT partition instead MBR, Still nothing.

The laptop is a sony vaio duo 13 and I have no legacy option in bios

View 3 Replies View Related

Setup Installation :: BIOS Boot Priority / Windows Loading Off Different Drive

Mar 10, 2013

Re-install windows 8 with new motherboard and CPU

I ended up managed to be able to boot into windows after i swapped out my motherboard and CPU to the new ones and everything seems to be working as it should, windows automatically installed the intel drivers and all my old programs and settings are there perfectly.

I can only boot into windows if i select my backup drive as #1 boot device in the BIOS, the SSD isnt even on the list.

The thing I don't understand lies in that, if i select my SSD as priority, where the directory of windows is installed, i get a bootmgr missing error - I've tried the various methods of recovering this using the cmd and a windows installation disc.

This isn't a huge issue but it's really tripping me out as to why this is occurring? I initially had some issues getting windows to boot so i installed a clean windows8 on this backup drive, i didnt change any settings at all. was only making sure that the SSD was being recognized and i hadn't corrupted it somehow. is it possible that the backup drive boot manager is directing it to the SSD.

View 7 Replies View Related

Setup Installation :: Windows 8 Boot Priority Device Not Saving On BIOS

Jul 17, 2014

I wanted to do a fresh windows 8.1 install (i have a samsung NP500P4C-T03CL notebook with windows 8 OEM preinstalled and when i updated to 8.1 the system went slow and "faily"). So i put the CD on the drive, but for my suprise when i reboted the system to enter the BIOS the F2 key didn't do the job, nor it appeared on the splash screen on samsung. After googling a lot and under trial/error concept i could enter the BIOS via Shift+Restart.

I did some changes to the BIOS booting set-up and noticed i have 2 Windows Boot Manager, the CD, the HDD and one option called "SETUP" that has a "!" ("!3.Setup"). So i tried every combination posible with Secure boot unabled, and UEFI+CSM OS, also with UEFI disabled, and none gave me the option to enter bios with F2, or recovery with F4. I managed to install win7 on another HDD. Main thing, besides the F2, F4, F8, F9, F12 (yes i prove all of them, even ESC), is that whenever i change the boot order it's not saved, and it is restablished to:

1. Windows Boot Manager
2. Windows Boot Manager
3. Setup
4. HDD
5. CD

Also i noticed that on the password options the one for the HDD appears grayed and as "FROZEN". I entered user and supervisor password, neither cleared the HDD one. i want to keep the BIOS update as a last resort. clearly it's not hdd related as the same thing happened when i tried another hdd with win7).

View 3 Replies View Related

Setup Installation :: Unable To Find Windows Boot Manager In UEFI BIOS?

Jul 24, 2014

Yesterday, after many, many problems with my computer, I finally decided to reinstall Windows 8.1 Pro onto my ASUS X200CA netbook. However, after backing up and reinstalling the OS, I found that when I tried to disable "Launch CSM" in my BIOS, all of my boot options would disappear and my laptop would continually boot into my BIOS. When I re-enabled "Launch CSM", the boot options would reappear - however, it had not included the "Option #1 - Windows Boot Manager" that I had seen in my other installation.

View 2 Replies View Related

Setup Installation :: Win 8.1 - Convert BIOS To UEFI

Apr 14, 2014

I have windows 8.1 installed on 120gb ssd. I also have a 1tb HDD too. So I was trying to install Hackintosh/Linux when I noticed that the System Reserved partition was on my HDD instead of the SSD. So, I used easybtc to migrate my boot files to my SSD. I deleted the system reserved partition. Now I want to convert my BIOS to UEFI. I have Z87 pro mobo.

I tried this tutorial: [URL] ....

But it seems to be geared at the C drive, where I don't have room for that 350mb as disk utility wont let me shrink it.

Edit: would downloading a third party partitioner, shrinking C about 350mb, or whatever is the minimum, and then use that new space as described in the guide work?

View 9 Replies View Related

Setup Installation :: Backup OS From BIOS Upon First Switch On?

Jan 8, 2013

Have just purchased this; HP Pavilion g6-2210sa 15.6" Laptop - Red Deals | Pcworld Upon hearing that I was up for the challenge of setting it up myself, the sales assistant pointed out that the very first thing I must do is back up the OS (windows 8).

I asked, 'oh, is the OS on a hidden partition?' .. and he said no, its in the BIOS. And I only have one chance to make a back-up copy, as soon as I switch on. Also; if I have software issues after that point, but haven't backed up the OS, I can't claim it under the manufacturer's warranty as an issue.

I believe that the .. key? .. is in the bios now, so I never have to worry about losing it, but apart from that .. egad.

Is there an auto-prompt, or do I need to do a regular ol' back-up .. and where do I back it up to, a separate hard drive/dvd etc?

So. I have this shiny, new, laptop. In it's shiny, new, unopened box, right now. And am starting to wonder if I should have coughed up the £50 to get 'em to set it up for me..!

View 6 Replies View Related

Setup Installation :: HDD Not Found But It Shows In BIOS

Jan 6, 2014

I just got a FM2-A75MA-E35 motherboard and a installing Windows 8 on a freshly formatted SATA HDD. My BIOS see's the drive and has it second in the boot order, just after the DVD-ROM drive. It has a label with the drive serial number and everything, along with the drive being 'enabled' in BIOS. When I get up to the spot to choose what drive to install Windows to, its says 'No drives were found, please select a storage driver'. I found that it shows C: when I browse for drivers. Why this isn't working?

View 1 Replies View Related

Setup Installation :: How To Reset Dell BIOS To Default

Apr 7, 2014

I have a Dell inspirion 15 laptop running Windows 8.1. A while ago I decided to try Ubuntu out. I installed it alongside Windows 8.1 in dual boot configuration with its own separate hard drive partitions. This means that when I powered on my laptop a GRUB menu (Linux boot manager) would come up allowing me to choose between Windows and Ubuntu. However, Ubuntu was more pain than it was worth so I decided to uninstall it. I did this by deleting the hard drive partitions that Ubuntu was installed on using Windows Disk Management. Now when I power on my laptop the GRUB menu still comes up but there are no options to choose from, only a command line interface. I now have to type Code: exit

which exits GRUB and takes me to my BIOS Boot Manager which looks like this:

Boot mode is set to: UEFI; Secure boot: OFF

UEFI BOOT
ubuntu (ST500LM012 HN-M500MBB)
UEFI Onboard LAN IPv6
UEFI Onboard LAN IPv4
Ubuntu (ST500LM012 HN-M500MBB)
Windows Boot Manager (ST500LM012 HN-M500MBB)

I then have to select Windows Boot Manager to boot into windows.

Why GRUB is still there even though I have deleted the Linux hard drive partitions? Also, why is Ubuntu still listed on the BIOS Boot options? And why is it listed twice?

View 4 Replies View Related

Setup Installation :: Changing BIOS Date Of Install

Mar 5, 2014

Will updating my BIOS changs the date of installation? If not, does the BIOS need to be replaced for this to occur? I am trying to apply to a job but their software is telling them my computer is too old. I've checked and the date they are showing is the BIOS date exactly.

View 9 Replies View Related

Setup Installation :: Switching From Legacy BIOS To UEFI

Jan 29, 2014

Right before I performed a clean install of Windows 8.1 x64 on my Inspiron 3520, I switched to the Legacy BIOS *facepalm*.

When I enter the legacy BIOS and enabled "secure boot", I performed a restart that gave the following message "internal hard disk drive not found, to resolve this issue, try to reseat the drive. No bootable devices--strike F1 to retry boot, F2 enter setup menu, F5 enter PSA". Of course, when I go back into the BIOS and disable secure boot, it reverts back to legacy and boots up Windows 8 just fine. What I'd like to know is, how can I revert back to UEFI so I can change the boot-up option and perform a clean install under UEFI.

Making the Switch to UEFI | sepago

[URL]

View 7 Replies View Related

Setup Installation :: ASUS M2N-E Won't Boot Win 8.1 After BIOS Update

Jul 2, 2014

It has an ASUS M2N-E motherboard with an old single core AMD Athlon 64 (I cannot remember which model specifically).

Last week, I provided him with a couple of old HDDs and 8GB worth PC-5300 DDR2 667 MHz RAM. We also installed Windows 8.1 64-bit, and other than the CPU being a single core and a bit slow, things were proceeding relatively smoothly.

He has an NVIDIA Geforce 8500 on the board, and he's ordered a PNY-made Geforce GTX 650 that's on it's way at present.

He's wanting to upgrade the CPU to the AMD PHENOM X4 9950, so we've been periodically meeting over the past couple of weeks to perform surgery on this old machine.

At any rate, we found that to update the CPU, we needed to update his BIOS from the one that was installed, which was at revision 0502. The needed BIOS revision for the CPU was 1504, but would also work with revision 1701.

After jumping through several hoops to update the BIOS, we updated it to 1701. However, since then the machine will not boot into Windows 8.1. He gets an instant BSOD. I did not see the error code, so I cannot say what it was. He told me that he's attempted to do a repair install to no avail. The repair attempt results in a constant loop of the machine rebooting and BSODing.

At any rate, here are some URLs that detail the board specs and the list of BIOS revisions for that board.

Motherboard Specs: Motherboards - M2N-E - ASUS
CPU Compatibility list: ASUSTeK Computer Inc. -Support- CPU Support M2N-E

View 2 Replies View Related

Setup Installation :: Can't Enable Secure Boot On BIOS

Oct 11, 2013

I had a bit of a problem with Malware which led me to reinstall windows 8. I had also at the time been trying to install Linux to dual boot beside it. However, upon reinstalling I got the annoying watermark saying "Secureboot isn't configured correctly." Having decided I would rather remove the watermark and having gone back into the BIOS (with a reinstall) and trying to enable secure boot I get a message - "CSM is Loaded! Disable the CSM via Setup and repeat operation after Restart".

However there is, as far a I can see no option to disable the CSM in my bios - I've tried disabling anything related to Legacy and reinstalling both Ubuntu and Windows 8 as well as wiping the drive and jumping the CMOS as well as updating the BIOS.

I've tried every permutation in the BIOS. Could possibly be an incompatibility with graphics card, but wouldn't know where to start on that end if it is.

View 9 Replies View Related

Setup Installation :: Laptop With Encrypted Key In UEFI BIOS - How To Obtain ISO

Nov 13, 2013

Have a toshiba laptop with the UEFI encrypted windows 8 key. The hard drive was broken as it was dropped. No sticker on the bottom as is now microsoft policy. Download of the windows install needs the windows key. Cant get it as it's encrypted. Found generic windows 8.1 keys which worked but it said it was the wrong key for those installs. Generic windows 8 keys don't work for the download. Going around in circles and not sure what to do.

View 9 Replies View Related

Setup Installation :: WHQL BIOS Settings On GIGABYTE Mainboards

Jan 26, 2014

I am installing Windows 8 and the Gigabyte mainboard gives three options regarding the OS

Which one to choose??

Originally Posted by BIOS Windows 8 Features
Other OSWindows 8Windows 8 WHQL

Obviously it is one of the Windows 8 options. Both will unlock a few new settings like the Compatibility Support Module (CSM) or (not visible on the screenshot) Secure Boot. But the new options are exactly the same if WHQL is chosen or not.

Originally Posted by "Gigabyte GA B85M-HD3 Manual OS Type

Allows you to select the operating system to be installed. (Default: Other OS) So, which to chose and why and what do they do?

View 6 Replies View Related

Setup Installation :: Using 64bit Version - Boot Win 8 On GPT Partition Via BIOS?

Apr 21, 2012

Will it be possible to boot Windows 8 from a GPT partition using BIOS (not UEFI)? I'll be using the 64bit version.

Technically, I know it's possible as I'm doing it with FreeBSD, many Linux distros etc. Using hybrid MBR/GPT, I've read others have Win7 booting off GPT partitons as all. I'd rather not go that route.

View 2 Replies View Related

Setup Installation :: Clean Installation Win 8 Failure (No Disk Space)

Aug 18, 2014

I partitioned my hard disk into a 150GB (C) and 500GB (D) and upgraded from Win7 to Windows 8 (and subsequently Windows 8.1 after the recent updates). The OS is installed onto the C Drive.

Performed a Clean Installation of Windows 8 on my C Drive. Under the Choose What To Keep Option, I selected Nothing.

Technically speaking my C Drive would have been wiped clean but after the Windows 8 installation, my C Drive only has 5GB of space left (145GB is being used). The Windows 8 OS is not detecting any of the old programs in my C Drive and the automated Disk Clean up feature only offers removal of temporary internet files. Which brings me to one possible assumption...

The Clean Installation Failed. Windows 8 simply installed itself again on my C Drive and the remaining disk space (containing my previous Windows 8.1 OS and programs) is locked down somewhere. I suspect this had something to do with changing my HD format 3 years ago when I wiped clean my pre-loaded ASUS laptop Win7 and partitioned it to install my Windows 8.

How to remove my previous OS?

View 2 Replies View Related

Setup Installation :: (Recovery) Partition In GPT Disk For UEFI Installation?

Jan 28, 2013

Is it possible not to have the partition "recovery"?

Because if you look at the two tutorials:

- UEFI (Unified Extensible Firmware Interface) - Install Windows 7 with - Windows 7 Forums

- UEFI (Unified Extensible Firmware Interface) - Install Windows 8 with

In the tutorial to install Windows 7 in UEFI, there is not that damn partition recovery, while in the tutorial for Windows 8, we can see it.

When I install Windows 7 (MBR mode), I avoid this partition "recovery" by creating a partition with a name before installation. I install the OS on it and everything is fine, no partition "recovery" But here, since one must delete all partitions, If I create a GPT disk with a partitioning tool before installing, is that it might be appropriate?

View 6 Replies View Related

Setup Installation :: New MSata Install From Acer Recovery USB - In Bios No Boot

Jan 14, 2014

These are the steps I've taken-- OS Win 8, pre-installed by Acer.

1) Make recovery USB using the Acer recovery wizard, with the laptop in stock configuration.

2) Install msata as secondary drive

3) Go to Computer management and initialize the msata and format with GPT style. Format the drive, assign a drive letter. (I only see 1 partition). I did this as NTFS/default allocation size. Is this where I went wrong?

4) Remove the factory HDD (listed as HDD0 in BIOS)

5) Boot to BIOS
5a) in BIOS, disable secure boot.
5b) Go to legacy mode
5c) Set msata (HDD1 in BIOS) as #1 in boot order

6) boot to USB recovery drive, follow steps to restore from USB (clean install, make partitions as it wants)

7) remove USB, reboot.

Error message-- no bootable device. I can basically load the USB again or the BIOS.

View 2 Replies View Related

Setup Installation :: Installing Windows 8 On A New Disk Boot

Aug 14, 2014

Before, my PC was setup like this:

- disk0: windows xp
- disk1: windows 7
Bios boot priority set to disk1.

So no boot loaders, when I (rarely) need xp, I would switch via bios

Now I wanted to try Windows 8, so I've

- download 'Windows 8.1 Enterprise Evaluation' and burnt on a dvd

- bought and connected a new disk (disk2)

- boot from dvd, installed choosing the new disk2

Now, everything works fine, Windows 8 got installed on disk2. But the strange thing is this:

- if, from bios, I choose disk2, it says the disk is not bootable

- choosing disk1, a boot loader shows up, letting me choose between win7 and Windows 8.1

(- choosing disk0, nothing has changed, xp starts like before)

So, I'm confused. I was expecting Windows 8 booting from the new disk2.

- why disk2 doesn't boot?

- would have been better physically disconnecting disk0 and disk1 before installing?

View 3 Replies View Related

Setup Installation :: UEFI USB Disk - Does Not Boot From Windows 8

Mar 13, 2013

Laptop: ASUS UX31A-DB71, latest BIOS: 218

Originally my laptop came with Windows 7 and when i looked at disk management my disks were formatted with UEFI schema. One of my friend gave me a UEFI bootable USB drive loaded with Windows 8. So, i thought why not give it a try. So, I created a backup of my OEM Windows 7 and saved the iso files in a seperate external HD (created twice just to be sure . Now, i decided to load the Windows 8. Booted into the BIOS and there is an option to select the USB drive along with the UEFI option for that USB drive. I selected the UEFI option but some reason it does not boot into UEFI.

So I decided to select the standard USB install and this option let me install windows 8. In the process of installing i formatted the partitions and made a single partition and installed Windows 8 on it. I am guessing now the drive is not GPT but MBR. I also noticed that his installation USB disk had an option to select either 32bit or 64bit of Windows 8... Would Microsoft create a same iso file with both versions? I am guessing he created the USB from a illegitimate source.

I am planning on purchasing Windows 8 Pro version as an iso but wanted to be confident that it would work with UEFI architecture.

Questions:
1. Why would the system NOT boot from UEFI?
2. If I download the legitimate iso from Microsoft and wanted to install Window8 Pro via UEFI, I am sure i would have to format my SSD to GPT and how would i go about formatting it during installation?
3. How would i create a recoverable USB for my iso image i created for Windows 7 via ASUS AI Recovery. Do I need to follow the same procedure as stated in creating bootable USB disk (i.e. FAT32 system) via diskpart utility?

View 9 Replies View Related

Setup Installation :: Restore Windows 8 To New Hard Disk?

May 8, 2014

the hard disk of a Samsung Ultra 5 crashed. I have got a new hard disk. How do i restore windows 8 and Samsung drivers to the new hard disk? My friend has an exact notebook. How do i copy the recovery partition from his pc and use it on mine?

View 9 Replies View Related

Setup Installation :: Creating Windows 8 X64 Install Disk?

Dec 8, 2013

I have a Toshiba Laptop System Model: Satellite L875D-S7332 Part Number: PSKFQU-008003 Pre Installed with Windows 8 x64. I want to create a Windows 8 x64 Install Disk.

View 9 Replies View Related

Setup Installation :: Windows 8 Cannot Be Installed To Disk 0 Partition 1

Nov 8, 2013

I am trying to do a clean install of windows 8 on my laptop (Elitebook 8770W) from a USB stick with original MS Windows OEM iso. Once I boot from usb stick, at the setup screen I enter the product key and then choose advanced to do a clean install. I then choose my hard disk partition to install windows but I get stuck here with this error:

"Windows cannot be installed to disk 0 partition 1"

I deleted the partition and choose to install on the unallocated space (150GIG) But still get the same error and when I click on the error this is what I get:

"Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's Bios"

In bios I have my disk set as Raid and I also have a m-sata Flash cache. If I change raid to AHCI I will be able then to install windows. But if I turn it back to raid after install I will no longer be able to boot I have to be in raid mode to use my m-sat as cache drive.

So here I am stuck not being able to install windows I even downloaded latest intel rapid storage technology drivers and put them on the usb stick with windows setup files. When i got the error I choose to load driver. But even after that I was getting same error and windows would not install on my HDD.

What's the right way to install in this condition (raid)?

View 7 Replies View Related

Setup Installation :: Trying To Install Windows 8 32bit From 64bit Disk

Jan 10, 2014

I have a copy of Windows 8.1pro 64 bit which I run on my main computer, I have an old laptop which is about 7-8 years old, I'd like to install a copy of Win 8 for test purposes and mess around with for a few months.

The laptop is so old it won't let me install 64 bit, is there a 32 bit version on the disk hidden away I could install or are they totally separate disks?

Is it possible to download a copy which would work for 30 days without entering a serial number or even an old beta copy.

View 2 Replies View Related

Setup Installation :: Windows 8.1 - Create Recovery Disk Fails

Aug 5, 2014

Brand new laptop. HP. 17e UEFI +GPT etc. Upgraded to 8.1 from 8, first thing. Then clicked on the MS, create recovery. (in blind hope of a clean 8.1 restore). Inserted (32gb stick) (later found out is illegal windows 8 version, that is not removable.) SD-extreme, 32gb. list on toms HW, as winner of all, (and is useless for this app).

So I pull out my very old SD cruiser glide, 32gb (old , slow and not win 8 cert (a good thing). Yes all 32gb extremes are mapped as HDD not removable media and is doomed. (known on all forums) but same error.

The cruiser shows up i device manager under removable media....btw i want to find out why the missing files error. I have a HDD and SSD, with latter mirrored. both the orig, HDD fails and SSD fails. same way. I parked the HDD , and run only SSD. but both fail... (my guess is , upgrades 8.0 to windows 8.1 is cause).

now the screen,
attached

How can i find the log of these errors, it's not in event viewer.. oddly. sfc/ scannow works. as does chkdsk, and restore (create) works,. and system is Fast a lightning. All HP apps works, cept there version of create disk for same reasons.

My HP create recovery now works on the GLIDE. (old very old 32gb stick i had laying about). So now I am thinking HP? blocks the MS create so you will use theirs? But I'd lilke to know this, what files are missing....

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved