since i while ago my laptop's wireless been behaving really weird. the wireless driver will suddenly disable and gone from the network list going into Device manager, it says "this driver is not installed " or sth like that. cant exactly rmb what it said, and sometimes the wireless bars in the bottom will show a yellow "!" with no connectivity with showing only the network i connected to. if i repair it the driver will be gone. almost have to repair like 10X times to get it come back on, (or i think i came back on itself) or sometimes just no network "no connections are available" 1st thought was virus, but did full scan.no virus. just did a Full Format and reinstall window, and 1st thing i've installed the wireless driver..still happaning.
For security reasons, I want to turn my Internet connection via my Netgear router on and off, as I like.In Windows XP it was eay. I could pull out a LAN icon from the Network connection section in the Control Panel to the desktop.Then all I needed was to click it and choose to disable/enable the Internet connection.I could also disable it from the tray icon and enable it from the LAN icon.In Windows 7 I don't find such a possibility. It is in the Internet all the time, or if I disable it, it is complicated to enable it again...
I have windows 7 home premium, and I am trying to disable deleting temporary files. I have tried through regedit, under HKey_Current_User under Software/Policies/Microsoft/Internent Explorer/ControlPanel, it is set to 1. It is working but how about to disable deleting temporary files?
I have a somewhat older Dell that is more than capable of running Windows 7 (it also runs Server 2008 R2 quite nicely). The problem is that the onboard ATI graphics only has 16MB of RAM and is only recognized as Standard VGA Adapter. This is really unjust, so I obtained an NVidia FX 5200 for next to nothing and placed it in a free PCI slot.
Much to my surprise, the BIOS has no settings for disabling the onboard video. It also has no settings for instructing it to look to the PCI first. As a result, the onboard video is always active during POST.
I disabled the onboard video from Device Manager, shut down, and installed the new NVidia PCI card. I rebooted with the monitor attached to the PCI card. Nothing. I switched the monitor to the onboard video and sure enough, there it was. The NVidia had also been detected and was showing up as a Standard VGA Adapter with Code 10 -- cannot start. Not a problem, I thought. I had yet to install the NVidia driver, and the onboard video had already claimed the default VGA during POST, so this was not surprising.
I installed the recommended 96.85 Forceware drivers for the NVidia FX 5200. These are the Vista 64bit drivers. Windows accepted it without problem and I swapped the monitor back to the NVidia during the reboot. What I was expecting is that the display would be blank during boot because the onboard video is active. I assumed Windows would switch to the NVidia when it started because I had installed the driver and instructed it to disable the onboard video.
I was wrong. Blank display. I switched back to the onboard video and my display returned. The Nvidia card was recognized in Device Manager and it was showing "This device is working properly". The onboard video still had the disabled icon next to it. Yet I cannot choose the NVidia when I go to Screen Resolution and other screen preferences. It is using a blank video adapter -- looks like VgaSave.
Have I gone wrong somewhere? Or is there a more appropriate driver I should be using? Thoughts and suggestions would be helpful. Keep in mind the onboard video cannot be disabled in BIOS, nor can the BIOS be instructed to look to the PCI first for video. There are no BIOS updates available. There is no AGP slot, only two PCI slots. This is what I have to work with.
To start, a quote from Windows 7 EULA: Quote: ... 2. INSTALLATION AND USE RIGHTS. a. One Copy per Computer. You may install one copy of the software on one computer. That computer is the "licensed computer." ... As the older geeks certainly remember, in earlier Windows versions it was possible to use different hardware profiles. You simply got a boot menu asking which hardware profile to boot.In 7 this is not possible. You have to manually disable or enable the hardware components when the need arises.
What if I install all the software I need, activate Seven, then create a system image. Shut down the computer, disconnect the Windows 7 HD, attach an equal new HD, use recovery tools to return the said image to this HD number 2. Put HD 1 back, use BCEDIT or a third party tool to create a boot menu which at this point would include two absolutely identical Seven installations.Then strip down Seven setup #2, disable all unnecessary devices etc. thus creating a Seven - Seven dual boot environment, with two different HW-profiles. The computer is the same, only one of the two Sevens could be used at any given time, and so on
