Shuttle Card Reader PC 23 (USB) - Error Code 10
I have tried several times to use my Shuttle Card Reader (PC23)Â that is connected to my mainbord on a free internal extended USB connector. Error message : Error Code 10 - can`t use device.
If I insert a SD Card in the SD slot on the Card Reader, and use the hardware trobleschooting in Windows 7 RC : Win 7 can reconise the SD Card and I can use it, but only during the session.
Next time i start the system I have the same error as before.
For this 4 in one Card Reader there is no Driver for Win XP or Vista nesesary, so i think there normally no driver needed for Windows 7 RC either.Â
View Replies (Posted: Thursday, August 13, 2009 7:50 PM)
Sponsored Links:
Related Forum Messages for Windows 7:
Conflict Between The Card Reader And Unknown Device Reported As Code 43
system Dell 519 Inspiron 64bit AMD. just installed Win 7 over Vista 64 bit. After booting the system the card reader works and is listed under "disk drives" in device manager. Insert an SD card and it reads and is fuctional. remove the SD card and re-insert it and there is a message that the system failed to recognize the device. going back to Device Manager the 4 card readers are not listed under Disk Drives and an error is reported under USB controllers. it is shown as: Unknown Device with a yellow! Properties for the Unk Device are: Device Type- USB controllers Location: Port_#0006.Hub_#0006 Device Status: Windows has stopped this device because it has reported problems. (Code 43) is there a conflict for this port? if so how can i troubleshoot the confict and resolve it?
Posted: Sunday, November 01, 2009 5:19 PM
View 5 Replies!
View Related
SDA Compliant Card Reader (Ricoh) Code 10 Cannot Start
I have a samsung x60 Plus which as of yet has no windows 7 specific drivers but it does have Vista. The laptop has a ricoh card reader (xd, sd smc) this does work as I have rebooted into XP and it reads and writes fine. In windows 7 I either end up with the standard SDA driver that Windows 7 installs which reports as working correctly but nothing happens when you enter a memory card OR I get error code 10 cannot start, depending on which set of the various vista and windows 7 drivers I have tried. So far I have tried; Generic Ricoh windows 7 card reader drivers Samsung x60 Vista card drivers and vista chipset drivers Windows standard drivers Anyone have any ideas..? Does seem to be a fairly common problem but I have tried quite a few solutions with no luck.
Posted: 4 Weeks Ago
View 9 Replies!
View Related
All In One USB 2.0 Card Reader No Drivers?
im running an evga sli 58x, and windows 7 64bit 7077 i have the RC1 version of windows 7 but i hate to install that and as i have all my games and everything id have to reinstall with it(major pain) plus im not even sure if that would fix my problem anyways when i plug my card reader in i can't access it at all, it does show up in device manager but it says drivers not installed. I don't think they make this card reader anymore and there would be drivers floating around for a card reader, so what are my choices?
Posted: 06-18-2009
View 0 Replies!
View Related
USB All In 1 Mini Card Reader
I bought this Generic USB All in 1 Mini Card Reader off eBay (Some Cheap chinese thing) It worked fine on my previous setup, Windows Vista x64, and it still works on my fathers computer, Vista x64 I believe. But When I try to connect it to my current Windows 7 x64 install, it justs gives me an I/O device error, I think it might have something to do with the Device driver for Win 7 It might not be compatible, I don't know just thought somebody might have an idea if I can get it to work in Windows 7.
Posted: 4 Weeks Ago
View 1 Replies!
View Related
Realtek USB 2.0 Card Reader X64 Issue
I have a notebook Gateway M 1617, with Realtek card reader but it doesn working with the new Windows 7 build 7100, I've tried go to realtek driver web site, downloaded the Windows 7 driver version also got the win vista version. but nothing worked for me..
Posted: 07-23-2009
View 1 Replies!
View Related
15 In 1 Card Reader USB Device Stops Functioning
When I get to my computer after being away I get the message that a USB device has been stopped and this is what I found. This driver responded slower than expected to the resume request while servicing this device: Driver File Name : Driverusbuhci Driver Friendly Name : UHCI USB Miniport Driver Driver Version : 6.1.7100.0 (winmain_win7rc.090421-1700)
Posted: Friday, June 05, 2009 10:54 PM
View 2 Replies!
View Related
Broadcom USB Smart Card Reader Not Working
After upgrading my Vista Business SP2 (32-bit) to Windows 7 Ultimate RC (32-bit) my Broadcom USB smart card reader does not work any longer (Dell Latitude E6400 with built in smart card reader). The newest available driver from dell support was already tested (Broadcom, driver date 09/23/2008, version 1.0.0.1, digitally signed WHQL, released by dell in March 09), but the device can not start (Error code 10) with Windows 7. With the Microsoft WUDF Driver (Usbccid, driver date 06/21/2006, version 6.1.7100.0) the device starts but whenever I insert my smart card an additional device is detected (other device - smart card) but no driver found - Error message is: The drivers for this device are not installed. (Code 28). What else can I try to get this reader working again (with vista sp2 the smart card reader was working fine with the broadcom driver)?
Posted: Tuesday, May 12, 2009 11:11 PM
View 11 Replies!
View Related
Dell USB Card Reader Not Working Properly
I have a Dell XPS Studio 435T that was running Vista Home Prem. 64 bit. My card readers were labeled G:, H:, I:, and J: and were there when I got the machine. C: and D: are the Dell Vista Home Prem. 64 bit OS and the Dell Restore partition, E: and F: are my DVD drives. These drives always appear. The system was built early May and was the A07 BIOS. When I needed to read an SD card, I plugged the card into the proper slot, nothing happened? Discovered the drive was NOT on Explorer nor COMPUTER desktop icon when double clicked. I have a Canon printer with card slots, put the card in the printer after I turned it on and I can read the card, so it isn't the card (unless the 435T's slot can't read 8GB SD cards). I don't get any errors when starting the system and nothing apparent in the Event Viewer. I called Dell figuring they'd be aware of this problem and have a suggestion. Wrong, they claim it isn't a common problem and is either a h/w problem or I 'did something' to the system that caused this. Suggested fix was to restore the system to the shipped state and I was not too happy about that. The Rep. then agreed to get on my system and look at it. I showed him the drives and the Device Manager that had an 'Unknown Device' and that it had no driver. I showed him that when I tried to update the drive it said I had the correct driver. I deleted that device and then had Device Manager search for changes and it found the same 'Unknown Device'. Now the Rep. thought I had a driver problem and proceeded to re-load the Intel Chipset drivers. I think I did replace those with more recent ones, but I let him. It installed INSTANTLY and the rep. said it meant I had the drivers installed... Checked the drives again, not there. Next step as for me to shut-off the system and restart into the BIOS screen and RESET the BIOS to the factory default. OK, but when the system booted, didn't do anything for the problem. Now the Rep. asked if I could open the case and check the cables to the reader bar. This was after he came back on-line after checking what to do next. By this time I decided I wanted to try something, I have a USB single card reader. I put the SD card into it and inserted it into the card readers USB connector. It found the device, although it didn't assign a drive? Put that same device into the USB connectors behind it and it had the same results but the Rep. was now convinced I had power to the card reader and wouldn't need to open the case. I then used a real USB Flash drive, put that in the card bar and it worked and could be read (and the Rep. wanted to connect and open the flash drive to be sure, which I allowed). So, the Rep. wants to REPLACE the h/w. From the reports I've seen, this is a waste of time. His response was he's never seen other reports of this failure and my only other choice is to restore Vista to the shipped state. So I OK'ed the h/w replacement. I know I've seen the drives as recently as 2 weeks ago. I was surprised one day when I opened Explorer and saw additional drives and then determined they were the card slots. As suddenly as they appeared, a few days later they were gone. Dell eventually replaced the device, cable from motherboard to it, and even the motherboard. In all cases, replacing that component had the card slots reappear on boot, only to disappear sometime later. This had been ongoing since July when I first discovered the problem. Only after I installed Win7 was the true problem discovered. I had a random BSOD under Vista with DVD Flick. Not often, but it happened. All I had to do was re-boot and it worked fine. Assumed it was a memory problem. After installing Win7 and booting after a BSOD from DVD Flick Win7 reported a USB device was not working properly and showed a list of USB devices. The suggestion, unplug and re-plug the device and if it didn't fix it, replace the device. Well, looking in Explorer, the card slots were gone. Unplugged the cable and put them back in (case had to be opened to do this) and booted, problem was gone. I've since removed DVD Flick and the problem has not come back. So, the question is why wasn't the USB port working properly? I assume an initialization problem, and I see a HOTFIX was just released for Nvidia systems with 4GB's of memory and USB devices stop working so I wonder if the USB drivers could be at fault here?
Posted: Wednesday, November 11, 2009 1:01 PM
View 2 Replies!
View Related
Installation Failed When Internal Card Reader Was Connected To USB Connector
I tried to install Windows 7 on a computer where the internal card reader was connected to the USB connector on the MB. This lead to an error message like "Windows could not terminate the system configuration..... please reboot. This message came up after each new reboot. Even boot in safe mode didn't change anything. I deleted the HDD completely and disconnected the card reader and restarted the installation. Then it worked fine. The problem came probably from the drive letter. The 2 DVD drives were now D: and E:. At the first installation D: to G: was taken by the card reader and the DVD drives got I: and J:Maybe this information will help others with the same problem.
Posted: Thursday, September 10, 2009 4:58 PM
View 1 Replies!
View Related
Wakes From Standby Doesn't Recognise USB Memory Card Reader
Most times when waking from a standby, the machine finds new hardware (a USB media card reader) and says it cant load drivers for it. It has a yellow (!) on in under Device Manager. I restart the computer and everything is back to normal. How can I stop this from happening? This is on a preconfigured HP M9340F machine.
Posted: Wednesday, October 28, 2009 5:54 PM
View 6 Replies!
View Related
ATI HD3870 Video Card Driver ISSUES - Error Code 0x00000116
My ATI HD3870 video card wont work...Upon downloading the windows 7 ATI CCC it informs me that there has been an error installing the driver...only for it to actually show up in the device manager as working, but then when I try to restart to set my MOBO to use it, I get a BSOD from atikmdag.sys error code 0x00000116 my Realtek AC'97 on-board audio card was working until reboot just like in another thread on this forum. At this point, however, isn't even showing up on the unknown devices list, nor ANYWHERE else on the Device Manager... Also there's an unrecognized and unsupported piece of hardware on my mobo (ACPIAWY0001.....WTF is this thing!?) I cant even begin to find drivers that might go to it for Win7x64 can anyone offer fixes for these problems? or should I just go back to vistax32? at least everything worked on there...
Posted: 10-25-2009
View 2 Replies!
View Related
Error Code 0x81000019 Backing Up On External Usb Drive
Using Windows 7 Professional 64 bit control panel backup and restore, backup consistently fails with the subject error. The Event Viewer/Windows logs/Application log shows multiple VSS errors. The suggested correction is to change the VSS service to manual so it may support backup. The VSS service is in manual. The external drive has no errors and has over 500 GB of free space.
Posted: Thursday, November 12, 2009 11:37 PM
View 4 Replies!
View Related
Error Code 12 In Card Video, ATI Radeon Mobility X1400, Display Adapter
I have the following problem at the moment of installing Windows 7, concretly with the Screen Adapter -display adapter-. If I install Windows XP or another version of windows the problem does not exist, for what I have rejected that is BIOS's problem. The problem is that Windows 7 install perfectly, but it does not recognize the adapter of screen (ATI Raedon Mobility x1400). I install all the available drivers, Windows Update, Catalyts 8.3, 9.2; official drivers, etc. This install without problem, however, I found the error when I entered Configuration of Hardware, and, recognized the display adapter, the mistake was error 12 (code 12): This device cannot find any free <type> resources to use. (Code 12) If you want to use this device, you must disable another device that is using the resources this device needs. However, it is not BIOS's mistake, because the cardvideo is recognized, and even it works well with other SO (WXP or WVISTA).
Posted: Saturday, May 09, 2009 5:05 PM
View 2 Replies!
View Related
Seagate Barracuda 7200.10 320gb USB Drive - Error Code 28
i have 3,5" seagate barracuda 7200.10 320 gb (16-MB cache) IDE hard drive. i want to tie up it with an IDE-USB transformer to my notebook (FS Amilo Pi 2540) but windows 7 does not recognize it. windows 7 shows it as an Unknown Device and gives Code 28 error. i made a search on google, and hard drive producers page. and also i tried to update the driver in windows. how can i use it with windows 7?
Posted: Tuesday, March 31, 2009 6:16 AM
View 6 Replies!
View Related
HP Nw8000 SD Card Reader
I'm running Windows 7 RC on HP nw8000 and I'm pretty sure the card reader worked ok on Vista Ultimate 32. Has anyone found a driver for the built-in SD card reader? HP doesn't list anything past XP on their site, not even for Vista for this device for this notebook.
Posted: 05-13-2009
View 1 Replies!
View Related
Sim Card Reader
I have "ideus Simply smart" card reader, have a sim card reader, the windows driver installer detect, I use Vista 64b drivers without problem, but the program don't connect. I wish to know if somebuddy have any idea.
Posted: Tuesday, May 19, 2009 5:28 PM
View 2 Replies!
View Related
Realtek 6 In 1 Card Reader
Since I installed Windows 7 64bit from Vista 32bit my card reader is not even recognized. More info: Realtek RTS5158 6 in 1 card reader Advent AIO-200 Anyone any workarounds on this issue? Hopefully with their final release problem will rectified, fingers crossed.
Posted: Â Â Â Â Â 09-21-2009
View 3 Replies!
View Related
Drivers For EMachines Card Reader
before i gutted it out and put all new stuff in, my computer was once an eMachines C6415. it has a built in card reader that 7 identifies, but just as a generic card reader. there are windows xp drivers for it that will give them certain icons and specify what kind of slot they are, but i can't find any for 7. they work and all, but i want them to show up in my computer with all the correct information (instead of the generic icon that just says "removable drive"). i can't find any 7 drivers for it. any help?
Posted: 11-02-2009
View 2 Replies!
View Related
Ricoh SD/MMC Card Reader
on my laptop (ASUS Z91N), I've got one left driver issue: the integrated memory card reader. It's called Ricoh SD/MMC controller, the latest driver having the best behavior found is 2003-10-20 (1.4.2.9) from ASUS website for WinXP. All other drivers found does nothing, they install but when I plug the card, nothing appears in "My computer". The problem is that when I plug a SD card, windows detects it, assigns a letter, but I am unable to open to look at the files. I get "Access denied" every time. When I try to format, it does it with the good size detected! I tested by looking with another computer. So, this problem is weird, I never had any issue similar to that in the past. Anybody here having the same problem?
Posted: 05-10-2009
View 3 Replies!
View Related
Memory Card Reader Problems
Are there any known compatibility problems with memory card readers? While running Win 7 Beta, my SD card reader worked fine. Since installing RC, it does not. The system detects that a card is inserted into the slot and demands a format. After trying to format the device I get an error message that Windows was unable to perform the format (no, the card is not write protected). I've tried several SD cards (2 2-gig and a 4 gig) and none work, although they do work (without a format) in other devices, such as a digital camera. So either I have a hardware problem with the card reader (always possible, but it's only 6 months old) or there's a problem with Windows 7 RC reading and writing to the card. Device Manager says the device is there and working correctly.
Posted: Tuesday, July 07, 2009 4:55 PM
View 6 Replies!
View Related
Realtek Card Reader Not Recognized
I've got an Acer 5735z laptop with a Realtek card reader, it was working fine under vista. I loaded up Windows 7 on a fresh install and all was well. I noticed it had install a generic driver for the card reader, so i updated the driver with the correct version from Acer. This was couple weeks ago and everything seemed fine until today, when I noticed the laptop now doesnt recognise the card reader. It doesnt even show up as an unknown device in device manager, it like it doesnt exsit. Ive downloaded the recent drivers for vista/windows7 to no avail. I've also tried unstalling the Intel usb contollers and even going back to the original version of the drivers again to no avail... the only thing i can think of is reverting back to the generic drivers supplied with Windows7, but i dont know where there located on the disk or on microsoft.
Posted: Tuesday, November 17, 2009 10:41 PM
View 5 Replies!
View Related
Smart Card Reader Issues
This is the only major showstopper for me in using Seven 95% ActivIdentity USB Reader V2 ActiveClient 6.1 Both work fine in Vista 64 on the same box in dual boot. In Vista the driver used is the generic MS usbccid.sys driver version 6.0.6001.18000 dated 6/1/2006 In Seven there are 4 MS drivers all version 6.1.7000.0 dated 6/21/2006: - scfilter.sys - WUDFUsbccidDriver.dll - winusb.sys - WUDFRd.sys In Device Manager status I get the "This device Cannot Start. (code 10)" message. If I uninstall the device and plug it back in I can see that Windows sees an ActivCard USB reader V2 (shows up in "Other Devices" while drivers are trying to install) but the install fails for the Microsoft Usbccid smartcard Reader (WUDF). I have tried the latest drivers to no avail.
Posted: 01-31-2009
View 9 Replies!
View Related
Scanner And Card Reader Are Not Working
after installing Windows 7 I've installed a chip card reader (SCM Microsystem SPR 532) and a scanner (Canon Lide 9). Both were working fine for a few hours. But now none of them is working anymore. The Device Manager shows me that both devices are working properly but I neither can scan nor use the card reader for online banking. I tried to reinstall the drivers but this didn't help. Does anyone has a clue about this strange behavior?
Posted: Sunday, June 28, 2009 7:20 AM
View 2 Replies!
View Related
Memory Card Reader Issue
I have a Memory card reader and on the windows explorer it shows all the card slots as drives. Is it possible for it to only show the slot that has media in (dare I say, like a mac)? The same with my optical drives, is it possible to 'hide' them only showing when they have mounted a an item of optical media? Or is this just pipe dreams, and only the preserve of unix based systems?
Posted: 08-09-2009
View 4 Replies!
View Related
Dell 2407 Monitor Card Reader
Has anyone gotten a card reader built into a dell monitor to show up in Windows 7? I got any and all updates to Win 7 I could find. I installed the latest Vista chipset drivers for my motherboard, and also tried some drivers from Intel. The Memory card reader just does not show up at all. There is also a memory card reader built into the printer and it works fine. At one point there were Dell SM bus drivers available as an optional update. I tried installing them, but they failed. Now, just yesterday they no longer show up in Windows update.
Posted: Thursday, February 12, 2009 2:34 PM
View 9 Replies!
View Related
|
TRACKER
