Last night my power went out. Every time my power fails Vista will only start up in safe mode. If I try to start it normally it just goes right into "Power Save" mode. This has happened a handful of times, however it is usually an easy fix. I would just go into safe mode and run system restore and restore my system to a previous date. This however did not work last night. I can still boot up in safe mode. All of my files are still there.
View 4 RepliesWhen ever i leave my computer idled for a long time the monitors turn black and i can't do anything but shut it down and start it up again. When i shut it down it says "Out of range input 1" Then i turn it off again and this time it has an error saying Vista didn't start up correctly, then i hit "start windows normally" then i can do stuff. How do i wake it up without shutting it down.
View 2 Replies View RelatedMy system unfortunately this afternoon had the power removed without warning. The system wasn't doing anything at the time but ever since will not boot correctly. It gets as far as doing the windows bar across the bottom of the screen then when I would expect the screen to show the revolving circle the screen goes to power save mode as if there is no longer a video signal. Booting into safe mode works but a normal boot is a none starter.
View 5 Replies View RelatedI put this in another forum but I'm pretty sure it was the wrong one so here is my problem. Last night my power went out. Every time my power fails Vista will only start up in safe mode. If I try to start it normally it just goes right into "Power Save" mode. This has happened a handful of times, however it is usually an easy fix. I would just go into safe mode and run system restore and restore my system to a previous date. This however did not work last night. I can still boot up in safe mode. All of my files are still there.?
View 9 Replies View RelatedOn my Acer lapto, vista battery status shows it is 100% charged, but only 30 minutes working time remains. The working mode has been set to 'balanced', but even changing it to 'power save' it only gains a couple of minutes.
I have my laptop for almost a year. Is it normal that the battery practically used up within a year? Or is perhaps something else wrong here? In the beginning it could almost last 3 hours. But with only 30 minutes you can't get any work done.
I've had issues in the past where I come to my computer after the monitor goes into power save mode and it won't turn back on. Knowing that my machine is locked I can just press CTRL-ALT-DEL, type my password to unlock it, and once it's unlocked the screen turns on. I can also use VNC to remote to my desktop and unlock it. The monitor does *not* turn on until after unlocking and re-opening the desktop. This didn't happen all the time, but fairly often, particularly when coming in in the morning. In the past I'd thought it was maybe due to UltraMon software that I'd installed to have different backgrounds on each of my monitors, but that has since been uninstalled.
This is becoming more of an issue now that we're pushing out power profiles to all of our machines however. Screens turn off after 5-10 minutes, so frequently when I come back to my desk I'll have this issue. I have a workaround, but I just received a report of another user having the same problem (though he's using XP Professional). I figured I'd try to resolve my issue first (since I have direct access to my PC; he's a remote user), then see if my fix takes care of his problem as well. I am running Vista Ultimate SP1 on a Dell Optiplex 745. The video card (Radeon X1300PRO) has a dual-head DVI cable connected to it running two Dell 1703FPs monitors.
is there any way to show the power plan in tray like in winxp so i can change between plans (balanced, power saver...)
View 7 Replies View RelatedSomething has changed in my Home Premium system such that I can no longer save to the desktop! When I try, I get an error message stating " You don't have permission to save in this location." I do not recall changing ANY permissions to prevent this. I did have a problem installing Office Home 2007 and maybe that caused a change. Where do I need to go to set the permission back to allow me to save to the desktop?
View 7 Replies View Relatedmy vista home edition 32 bit hangs on the loading screen and does nothing. iv tried doing the start up repair thing but that didnt work, iv done a virus scan but it has come up with nothing. this problem is really annoying
View 4 Replies View RelatedI've just started having boot problems with Vista. I've had no problems in the past, but earlier this evening it would restart itself while loading Vista (the green bar loading stage). I used the Startup Repair option from the Vista install disc, and the log shows it successfully repaired a corrupted system volume (exact wording may have been different). Now it boots as far as loading a black screen and the mouse cursor, but doesn't get to the Aurora (blue-Vista-Windows-logo-loading thing). I have tried subsequent Startup Repairs, CHKDSKs, Memory Diagnostic checks, all with no errors to report. Unfortunately, I disabled System Restore a while back... Something I now regret doing! At least I know what I'll be doing as soon as I get it running again! My system is an ASUS M2N-E motherboard, AMD Athlon64 X2 6000+, Corsair 2x1GB XMS2 RAM, Sapphire ATi Radeon 3850... And so on and so forth. I'm running Vista Ultimate 32bit as well.
View 9 Replies View RelatedI just purchased a machine with a 64 bit OEM. I have created another partition because I want to install 32 bit on there. However, it is not working so I was wondering if there was something I am not doing right here. I want to use the 32 bit for internet access and itunes and the 64 bit for gaming. I do not have any discs with the 64 bit OS on it either everything I have here is 32 bit.
View 9 Replies View RelatedCan I partition my HD to two partitions, Install my copy of winXP pro on both (its only on one comouter so that shouldnt violate anything) and then upgrade one of them to vista using an upgrade disk? Will both windows work fine?
View 9 Replies View RelatedA friend's Vista computer started booting only as far as the round Vista logo then froze. I took the PC home and using my keyboard, mouse and monitor did some maintenance, upped the memory etc and took it back. It still froze at the logo. I replaced the keyboard and mouse and monitor one by one to no avail. Took everything home and it worked as a system, but at his house - still freezes. Is this an electrical problem - if so how could I find out? Their other computer works fine.
View 9 Replies View RelatedAfter booting up the computer the desktop freezes immediately. If it doesn't freeze up immediately I'll have some functionality, but minimal. I'll no longer have access to the internet (no network adapter present), can't run programs (they fail to open) or can't install programs/updates. I have even gotten a couple of Blue screen error messages such as: IRQL_NOT_LESS_OR_EQUAL and DRIVER_IRQL_NOT_LESS_OR_EQUAL.
In safe mode with networking I do have access to the internet. When I try to download updates in safe mode I can't because Install shield will not work, or some other excuse. There are no restore points to restore to. There was a Windows Framework update on August 7th. I tried to uninstall it, but apparently it was never installed properly. No blue screens while in Safe Mode. I've been trying to problem solve this on my own, but with my limited computer repair skills I'm scared to try things.
If I want to boot from the CD drive on ocassions, but otherwise boot
from the hard disk. How can I achieve this.
i have a Sony Vaoi VGN-NS11J im not sure if its a 32-bit or 62-bit. one day i was browseing facebook when my computer froze after leaving it for like 30 mins it was still frozen so i had to turn it off by the button and i know that is bad. when i tried to turn it on again it just gave me the options safe mode safe mode with networking and the other safe mode and start windows normally so i just started normally it gets past the vaoi screen and then on the microsoft windows screen it just keeps loading for like 10 minutes then it restarts then it gave me new options start windows normally or launch startup repair so i launch startup repair which takes like 40 minutes just to get to the actually repair place then it gives me no operating system to repair its just blank ive tried all the booting options start from last known good boot or something like that safe mode wont work and when i disable restart when startup fails i get the blue screen of death it gives me this message. A problem has been detected and windows has been shut down to prevent damage to your computer
UNMOUNTABLE_BOOT_VOLUME
I have a Gateway laptop that has (or had ) Windows Vista Home Premium x86 installed. It was a dual core Turion with 2GB RAM. Anyway, here is my problem(s):
When the computer first comes on, right after the Gateway screen it tells me:
System Config Data Read Error.
That is right when it turns on. The BIOS detects the hard drive just fine.
The second problem is:
It tells me that
Windows Failed to start. File: BootBCD
Status: 0xc000000f
Info: An error occurred while attempting to read the boot config data.
I tried to do a system repair with the Vista CD. It took about 10 times for it to work. If I turned the computer off, there is a 50/50 chance it would do the same thing and not work. I was chatting with Gateway support yesterday and the tech told me that Windows could be messing with the BIOS. I find that strange because I thought onceWindows took over, the BIOS has nothing to do with how the computer operates.
Well, I tried doing a system repair and it does not detect the Windows install at all. I figured well, I'll do a clean install and get rid of all of the crap that Gateway puts on their computers. I did that. I was able to make a new partition and format the drive. Windows is able to see the drive, but it tells me that it does not meet the criteria for the install. It will not go any further then that.
Gateway is going to replace the hard drive and if that does not work, they are going to service the laptop because I've only had it for a few months now. It worked fine on Tuesday, on Wednesday it did not work at all. Even with the hard drive out, it still tells me System Config Data Read Error on the BIOS screen. Just wanted to see what everyone else thinks.
I'm leaning more towards a drive controller failure or BIOS problem. If that is the case, then the motherboard needs to be replaced,
I have a pc running win xp media centre mp pc is dual core amd 64 bit 5200+ 2gb ram nvidia pcie 256mb graphics my hard disk is partitioned and xp is installed on the first partition I am trying to install Vista ultimate 64 bit on the second partition.
The vista installation will not complete I get an error when it is completing setup, saying that the pc shut down before installation was completed & the installation can not continue. The pc works fine under XP, are there any known installation issues with a Vista XP dual boot system?
i insalled vista ultimate and every time i go to restart the PC it will shout down but it won"t restart it stays on a black screen,i have to push the power button and turn it off and then press enter and it starts up.
View 6 Replies View RelatedMy laptop (Sony vaio w/Home Premium) came with a trial version of Norton 360. I decided that would uninstall it and replace it with Avast! free home. I uninstalled Norton and any other Symantic software found in Add/remove programs. I also ran the Norton removal tool that someone posted a link to. Everything seemed fine. I noticed that Sony said I had a few software updates that needed to be downloaded & installed. I downloaded them and installed them. Still everything seemed fine.
I had downloaded an earlier version of Avast last month to install on another computer. I had also downloaded the lastest version last night. I accidently installed the earlier version. It installed without any problems but soon notified me that an newer version existed. I then installed the lastest version OVER the installed version. I guess this is where I goofed.
After the install completed the computer needed to reboot. Well the computer would not fully shutdown. My screen went black but the mouse was till lit and I could move the curser. I let the computer sit this way for about 20 minutes. I was finally able to get the computer to shut down by hitting the power button a few times.
This morning when I hit the power button the computer immediately went back to this odd state. Curser worked but no windows. I hit the power button a few times and the computer finally acknowledged it had a problem and allowed me to boot in safe mode. From here I did a system restore to yesterday morning. The computer is fine right now but I would still like to replace Norton with Avast. Then I would like to install SP1.
I can't find an active WinXp64 forum, and everyone has been very helpful here. I have a WinXp64 machine that is in a boot cycle. It goes through the whole sequence, then right as it should start the desktop, it reboots. All external peripherals are unplugged. Sometimes I can see a very quick flash of a blue screen of death, but can't make anything out as to what the error is. We have tried booting in safe mode and command prompt, but they also just reboot. How can we get it to boot again?
View 6 Replies View RelatedIt's not just an ordinary not booting it doesnt show up anything after the bios screen....so i installed linux and i cant get windows vista to show up in the boot loader screen i can see all the contents of windows vista in linux and is there a way i could modify something in the vista drive to get it showing up again?
View 4 Replies View RelatedI have a copy of Vista which does not start properly in normal or safe mode. The desktop does not appear. When the PC boots I can sign on, but the screen with 'Windows' and a green background just remains and the disk light continues to flash. If I leave the PC long enough it goes to sleep and then will restart in this state. CTRL+ALT+DEL does not start the taskmanager. I can boot the PC using other operating systems. Is there anyting that I can do to make this copy of Vista start?
View 4 Replies View RelatedI have an Enpower tower that originally had XP on it then I got the Vista upgrade disc and have been having trouble booting up. I had took my tower to a local repair shop and they thought I needed a whole new mother board.
View 4 Replies View RelatedI have an Enpower tower that originally had XP on it then I got the Vista upgrade disc and have been having trouble booting up. I had took my tower to a local repair shop and they thought I needed a whole new mother board. I don't think so though because my tower worked fine before upgrading to Vista.
View 4 Replies View RelatedSomeone once told me he could boot into vista x64 from cold in just 6 seconds, just cant believe that, he had a velociraptor in raid. I have a regular raptor and have tried every trick under the book to get a faster boot, normally take around a minute, even with a quadcore pc with 8gb ram... my partners laptop takes around 30 seconds off that and is nowhere near as powerful. Does anyone have any mega tips for fast boots apart from the dreaded hibernation? I even tried a OCZ SSD but thought they were a waste of money for the like 2 second difference.
View 4 Replies View RelatedI got myself vista64 and have noticed the boot up process is extremely slow, it takes 3-5 mins to boot itself up to Windows. Is this normal? I read somewhere that it's going to be like this for a while until Vista learns the boot process? I just some how stumbled onto this site and thought I'll ask and sincerely apologies if this has been asked. What I have noticed is that once my G11 keyboard lights up, it starts to load windows up.
View 9 Replies View RelatedI have an HP TX2508ca convertable tablet laptop. I've had it for nine months and it runs on Vista Home Premium 32bit. Just yesterday I removed the keys and cleaned out the keyboard. After fixing the keys back everything was working perfectly. However, this morning things started to go a little crazy. There is only one account on the laptop and that is my admin account which is password protected. My password has the lower case letter " l " in it but they " l " key on the keyboard had stopped working. So I tried to type it in using the on screen keyboard but still nothing. I tried restarting and repairing but still no go. The letter " l " key just simply doesn't workk; be it on the regular keyboard or on the on-screen keyboard. So now, I'm locked out of my account because the " l " key doesn't work.
View 3 Replies View RelatedIs it the DVD-Drive or the mainboard (with its BIOS or the onboard
controller)?
I've just got a new computer with Vista. I want to set up a dual boot system so that I can also access XP.
I have read that this is much easier to do if XP is the first OS, followed by installing Vista, but I can't do that.
I have also read that it can still be done by creating a new partition from within Vista, then installing XP into that. I understand that this process will overwrite the Vista boot loader and the computer will then only boot into XP, but that a programme called VistaBoot PRO can then be used to reset that, and you are then left with dual-booting.
But has anyone had any experience of doing this? Or are there any foreseeable problems.
E.g. - when I start installing XP, will it need access to the motherboard/graphics card drivers?
One thing I'm wondering about is, at the stage where I can only boot into XP, the hard disk is a SATA one (no RAID set up) and I seem to recall XP having issues with these at boot-up?
last Sunday(may 3rd 2009) i updated my bios (unfortunately). problem is, vista (Home Premium 32 bit which i used when problem occurs) is not booting my HDD. after showing my bios screen black screen appears with blinking cursor. i removed and inserted bios jumper for recovery and also battery. but the problem didn't solved. fortunately windows xp is working without problem. now iam using XP professional. i dont know whats the problem.
View 9 Replies View Related